Hisense HS312 User manual

Quick Start Guide
3.1CH Soundbar with wireless subwoofer &
Dolby Atmos
Model: HS312
1
2
Remote control
What’s in the Box
Main Unit Remote Control /
AAA Batteries x 2 Wireless Subwoofer
AC Power Cord x2
1 Switch the unit between ON and
STANDBY mode.
2 (MUTE) Mute or resume the sound.
3 SOURCE Select the play function.
4 (BT) Select the Bluetooth mode.
5 VOL+/VOL- Increase/decrease the volume level.
6 /Skip to previous/next track in
Bluetooth/USB mode.
7 /PAIR Play/pause/resume playback in
Bluetooth/USB mode.
Press and hold to activate the
pairing function in Bluetooth mode
or disconnect the existing paired
Bluetooth device.
8 EQ Select a preset sound eect.
9 SURR Adjust the surround ON/OFF.
10 DIMMER+/- Adjust display brightness.
11 BASS Press to activate the bass setup.
12 TREBLE Press to activate the treble setup.
Replace the Remote Control Battery
1 Press and slide the back cover to
open the battery compartment of
the remote control.
2 Insert two AAA size batteries
(included). Make sure the (+) and (–)
ends of the batteries match the (+)
and (–) ends indicated in the battery
compartment.
3 Close the battery compartment cover.
HDMI Cable
- Do not mix old and new batteries;
-Do not mix alkaline, standard (Carbon-Zinc) or
rechargeable (Ni-Cd, Ni- MH, etc.) batteries.
Identifying the Parts












7
3 4 5
1 2 3
13
6
OPT
1 2
7 8 9 10 11 12
Identifying the Parts
Main Unit
1Remote Control Sensor
Receive signal from the remote control.
2 Display Window
Show the current status.
3(ON/OFF) button
Switch the unit between ON and Standby
mode.
4 (SOURCE) button
Select the play function.
5 VOL+/VOL- buttons
Increase/decrease the volume level.
6Screws
Remove the screws then install the wall
mounting screws into the back of the unit.
7USB Socket
Insert the USB device to play music.
8LINE IN Socket
Connect to an external audio device.
9 OPTICAL Socket
10 COAXIAL Socket
11 HDMI OUT (ARC) Socket
Connect to a TV via HDMI cable.
12 HDMI IN 1 / HDMI IN 2 Sockets
13 AC~ Socket
Connect to the power supply.
Wireless Subwoofer
1 AC~ Socket
Connect to power.
2 PAIR button
Press activate the pairing function between
the main unit and the subwoofer.
3 PAIR Indicator
Light stops blinking once the Subwoofer is
paired with the Soundbar.
EN
Wall Mounting Screws (x2) / Brackets (x2) /
Bracket Screw (x2) / Wall Anchors (x2) User Manual/Quick Start Guide/ Wall Mount Guide
Optical Cable

Quick Start Guide
3.1CH Soundbar with wireless subwoofer &
Dolby Atmos
Model: HS312
1
2
Remote control
What’s in the Box
Main Unit Remote Control /
AAA Batteries x 2 Wireless Subwoofer
AC Power Cord x2
1 Switch the unit between ON and
STANDBY mode.
2 (MUTE) Mute or resume the sound.
3 SOURCE Select the play function.
4 (BT) Select the Bluetooth mode.
5 VOL+/VOL- Increase/decrease the volume level.
6 /Skip to previous/next track in
Bluetooth/USB mode.
7 /PAIR Play/pause/resume playback in
Bluetooth/USB mode.
Press and hold to activate the
pairing function in Bluetooth mode
or disconnect the existing paired
Bluetooth device.
8 EQ Select a preset sound eect.
9 SURR Adjust the surround ON/OFF.
10 DIMMER+/- Adjust display brightness.
11 BASS Press to activate the bass setup.
12 TREBLE Press to activate the treble setup.
Replace the Remote Control Battery
1 Press and slide the back cover to
open the battery compartment of
the remote control.
2 Insert two AAA size batteries
(included). Make sure the (+) and (–)
ends of the batteries match the (+)
and (–) ends indicated in the battery
compartment.
3 Close the battery compartment cover.
HDMI Cable
- Do not mix old and new batteries;
-Do not mix alkaline, standard (Carbon-Zinc) or
rechargeable (Ni-Cd, Ni- MH, etc.) batteries.
Identifying the Parts












7
3 4 5
1 2 3
13
6
OPT
1 2
7 8 9 10 11 12
Identifying the Parts
Main Unit
1Remote Control Sensor
Receive signal from the remote control.
2 Display Window
Show the current status.
3(ON/OFF) button
Switch the unit between ON and Standby
mode.
4 (SOURCE) button
Select the play function.
5 VOL+/VOL- buttons
Increase/decrease the volume level.
6Screws
Remove the screws then install the wall
mounting screws into the back of the unit.
7USB Socket
Insert the USB device to play music.
8LINE IN Socket
Connect to an external audio device.
9 OPTICAL Socket
10 COAXIAL Socket
11 HDMI OUT (ARC) Socket
Connect to a TV via HDMI cable.
12 HDMI IN 1 / HDMI IN 2 Sockets
13 AC~ Socket
Connect to the power supply.
Wireless Subwoofer
1 AC~ Socket
Connect to power.
2 PAIR button
Press activate the pairing function between
the main unit and the subwoofer.
3 PAIR Indicator
Light stops blinking once the Subwoofer is
paired with the Soundbar.
EN
Wall Mounting Screws (x2) / Brackets (x2) /
Bracket Screw (x2) / Wall Anchors (x2) User Manual/Quick Start Guide/ Wall Mount Guide

PAIR
3s
2
Connections
3
4
◎Pair up with the subwoofer
OPTICAL COAXIALAUDIO OUT Headphone
A
B
●Before connecting the AC power cord, ensure you have completed all other connections.
13
Basic Operation
◎ Standby/ON
When you rst connect the main unit to the mains socket, the main
unit will be in Standby mode.
• Press the button on the unit or on the remote control to
switch the unit ON.
• Press the button again to switch the unit back to STANDBY mode.
• Disconnect the mains plug from the mains socket if you want to
switch the unit OFF completely.
Auto Wake
If a TV or an external device is connected, the unit will switch on
automatically when the TV or the external device is switched on.
Automatic Power O Function
The unit automatically turns to Standby mode after about 15
minutes if the TV or the external unit is disconnected, switched o.
◎Select Modes
Press the (SOURCE) button repeatedly on the unit or the SOURCE
button on the remote control to select the LINE IN, OPTICAL, COAXIAL,
HDMI ARC, HDMI 1, HDMI 2, BT (Bluetooth) and USB mode. The
selected mode will show on the display.
◎Adjust the Bass/Treble Level
• Press TREBLE then press VOL+/- button to increase or decrease
the treble. (TREBLE+8 / TREBLE–8)
• Press BASS then press VOL+/- button to increase or decrease the
bass. (BASS+8 / BASS–8)
• After about 5 seconds, the unit will exit from bass/treble setting.
The display will show the current selected mode. You may now
press the VOL+ / - buttons to adjust volume.
◎Turn the Surround Sound ON/OFF
Press the SURR button on the remote control to turn on the surround
sound. Press this button again to turn o the surround sound.
◎Adjust the Volume
Press the VOL+ / VOL- buttons on the unit or on the remote control
to adjust the volume.
If you wish to turn the sound o, press the (MUTE) button on the
remote control. Press the (MUTE) button again or press the VOL+ /
VOL- buttons to resume normal listening.
◎Adjust the Brightness
Press the DIMMER +/- buttons on the remote control to select
brightness level.
◎Select a Preset Sound Eect
While playing, press the EQ button on the remote control to select
desired preset equalizers: MOVIE, MUSIC, NEWS.
The subwoofer and the soundbar will be paired automatically when both are powered on.
If no audio from the wireless subwoofer can be heard, manually pair up the subwoofer.
● DolbyAtmos
Dolby Atmos® is available
only in HDMI mode.
1. To use Dolby Atmos® in HDMI 1
and HDMI 2 mode, Your TV had
to support Dolby Atmos® or
HDMI audio passthrough.
2. Make sure that“No Encoding“ is
selected for bitstream in the audio
output of the connected external
device (e.g. Blu-ray DVD player, TV etc.).
3. While entering Dolby Atmos / Dolby
Digital / PCM format, the soundbar will
show DOLBY ATMOS / DOLBY AUDIO /
PCM AUDIO.
4. While the soundbar is using Dolby
Atmos audio, you can only adjust the
bass level of the subwoofer. All other EQ
eects will not be available.
HDMI IN
HDMI (ARC)
OR
AV equipment
HDMI OUT
5Bluetooth( ) Operation
Settings Bluetooth
Bluetooth
DEVICES
Hisense HS312
Now Discoverable
Connected
21 3
no bT
bt
< 8 m / 27 ft

PAIR
3s
2
Connections
3
4
◎Pair up with the subwoofer
OPTICAL COAXIALAUDIO OUT Headphone
A
B
●Before connecting the AC power cord, ensure you have completed all other connections.
13
Basic Operation
◎ Standby/ON
When you rst connect the main unit to the mains socket, the main
unit will be in Standby mode.
• Press the button on the unit or on the remote control to
switch the unit ON.
• Press the button again to switch the unit back to STANDBY mode.
• Disconnect the mains plug from the mains socket if you want to
switch the unit OFF completely.
Auto Wake
If a TV or an external device is connected, the unit will switch on
automatically when the TV or the external device is switched on.
Automatic Power O Function
The unit automatically turns to Standby mode after about 15
minutes if the TV or the external unit is disconnected, switched o.
◎Select Modes
Press the (SOURCE) button repeatedly on the unit or the SOURCE
button on the remote control to select the LINE IN, OPTICAL, COAXIAL,
HDMI ARC, HDMI 1, HDMI 2, BT (Bluetooth) and USB mode. The
selected mode will show on the display.
◎Adjust the Bass/Treble Level
• Press TREBLE then press VOL+/- button to increase or decrease
the treble. (TREBLE+8 / TREBLE–8)
• Press BASS then press VOL+/- button to increase or decrease the
bass. (BASS+8 / BASS–8)
• After about 5 seconds, the unit will exit from bass/treble setting.
The display will show the current selected mode. You may now
press the VOL+ / - buttons to adjust volume.
◎Turn the Surround Sound ON/OFF
Press the SURR button on the remote control to turn on the surround
sound. Press this button again to turn o the surround sound.
◎Adjust the Volume
Press the VOL+ / VOL- buttons on the unit or on the remote control
to adjust the volume.
If you wish to turn the sound o, press the (MUTE) button on the
remote control. Press the (MUTE) button again or press the VOL+ /
VOL- buttons to resume normal listening.
◎Adjust the Brightness
Press the DIMMER +/- buttons on the remote control to select
brightness level.
◎Select a Preset Sound Eect
While playing, press the EQ button on the remote control to select
desired preset equalizers: MOVIE, MUSIC, NEWS.
The subwoofer and the soundbar will be paired automatically when both are powered on.
If no audio from the wireless subwoofer can be heard, manually pair up the subwoofer.
● DolbyAtmos
Dolby Atmos® is available
only in HDMI mode.
1. To use Dolby Atmos® in HDMI 1
and HDMI 2 mode, Your TV had
to support Dolby Atmos® or
HDMI audio passthrough.
2. Make sure that“No Encoding“ is
selected for bitstream in the audio
output of the connected external
device (e.g. Blu-ray DVD player, TV etc.).
3. While entering Dolby Atmos / Dolby
Digital / PCM format, the soundbar will
show DOLBY ATMOS / DOLBY AUDIO /
PCM AUDIO.
4. While the soundbar is using Dolby
Atmos audio, you can only adjust the
bass level of the subwoofer. All other EQ
eects will not be available.
HDMI IN
HDMI (ARC)
OR
AV equipment
HDMI OUT
5Bluetooth( ) Operation
Settings Bluetooth
Bluetooth
DEVICES
Hisense HS312
Now Discoverable
Connected
21 3
no bT
bt
< 8 m / 27 ft
Roku TV Ready and the Roku TV Ready logo are trademarks of Roku, Inc.