Hitachi P-N23NA2 User manual

–
–
INSTALLATION &
OPERATION
MANUAL
AIR PANEL
MODELS
P-N23NA2
P-AP160KA3
INSTALLATION AND OPERATION MANUAL
MANUAL DE INSTALACIÓN Y FUNCIONAMIENTO
INSTALLATIONS- UND BETRIEBSHANDBUCH
MANUEL D’INSTALLATION ET DE FONCTIONNEMENT
MANUALE D’INSTALLAZIONE E D’USOI
MANUAL DE INSTALAÇÃO E DE FUNCIONAMENTO
INSTALLATIONS- OG BETJENINGSVEJLEDNING
INSTALLATIE- EN BEDIENINGSHANDLEIDING
INSTALLATION- OCH DRIFTHANDBOK
ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ ΚΑΙ ΛΕΙΤΟΥΡΓΙΑΣ
EN
ES
DE
FR
IT
PT
DA
NL
SV
EL
BG
CS
ET
HU
LV
LT
PL
RO
RU
РЪКОВОДСТВО ЗА ИНСТАЛИРАНЕ И ЕКСПЛОАТАЦИЯ
NÁVOD K MONTÁŽI A OBSLUZE
PAIGALDUS- JA KASUTUSJUHEND
TELEPÍTÉSI ÉS ÜZEMELTETÉSI ÚTMUTATÓ
UZSTĀDĪŠANAS UN EKSPLUATĀCIJAS ROKASGRĀMATA
MONTAVIMO IR NAUDOJIMO VADOVĄ
INSTRUKCJA MONTAŻU I OBSŁUGI
MANUAL DE INSTALARE SI OPERARE
ИНСТРУКЦИЯ ПО МОНТАЖУ И ЭКСПЛУАТАЦИИ
PMML0569 rev.0 - 01/2021

PMML0569 rev.0 - 01/2021
III
This product contains biocidal substances according to EU Reg. 528/2012
Este producto contiene sustancias biocidas según el Reg. UE 528/2012
Dieses Produkt enthält Biozide nach EU Verordnung 528/2012
Conformément à la Reg UE 528/2012, ce produit contient des substances biocides
Questo prodotto contiene sostanze biocidi ai sensi del Reg. UE 528/2012
Este produto contém substâncias biocidas de acordo com o Regulamento (UE) N.º 528/2012
Dette produkt indeholder biocider i henhold til EU-forordning nr. 528/2012
Dit product bevat biociden volgens Europese Richtlijn 528/2012.
Denna produkt innehåller biocider i enlighet med den europeiska förordningen 528/2012
Αυτό το προϊόν περιλαμβάνει βιοκτόνες ουσίες σύμφωνα με το κανονισμό ΕΕ 528/2012
Този продукт съдържа биоцидни вещества съгласно Регламент на ЕС 528/2012
Tento výrobek obsahuje biocidní látky podle nařízení EU 528/2012
Toode sisaldab biotsiide vastavalt ELi määrusele 528/2012
A termék biocid anyagokat tartalmaz az 528/2012 EU rendelet szerint
Šis produkts satur biocīdās vielas saskaņā ar ES regulu 528/2012
Šiame gaminyje yra biocidinių medžiagų, numatomų ES reglamente 528/2012
Niniejszy produkt zawiera substancje biobójcze zgodne z rozporządzeniem UE 528/2012
Acest produs conține substanțe biocide conform Regulamentului UE 528/2012
Этот продукт содержит биоцидные вещества в соответствии с Регламентом 528/2012 ЕС.
Biocide property / Propiedad biocida/Biozide Eigenschaft / Propriété biocide / Proprietà biocida / Propriedade biocida / Biocide
egenskaber / Biocide eigenschappen / Biocidegenskaper / Ιδιότητα του βιοκτόνου / Биоцидно свойство / Biocidní vlastnost / Biotsiidne
omadus / Biocid tulajdonság / Biocīdu īpašums / Biocidinė savybė / Właściwości biobójcze / Proprietate biocidă / Биоцидный
Antibacterial / Antibacteriana / Antibactérienne / Antibatterica / Antibakterielle / Antibacteriana / Antibakterielle / Antibacteriëel
/ Antibakteriellt /Αντιβακτηριακές / Антибактериално / Antibakteriální / Antibakteriaalne / Antibakteriális / Antibakteriāls /
Antibakterinis / Antybakteryjne / Antibacterian / Антибактериальный
Active substance/Sustancia activa/Aktivsto󰀨e/ Substances actives/Principi attivi/ Substância ativa/Virksomt stof/Actieve stof/
Verksamt ämne/ Δραστική ουσία/ Активно вещество/ Účinná látka/ Toimeaine / Hatóanyag / Aktīvā viela / Aktyvi medžiaga /
Substancja czynna / Substanță activă / Активное вещество
Silver / Plata / Silver / Argent / Argento / Prata / Sølv / Zilver / Silver / Άργυρος
Сребро / Stříbro/ Hõbe / Ezüst / Sudrabs / Sidabras / Srebro / Argint / Серебро CAS Nº: 7440-22-4
These substances are NOT harmful to human health nor the environment
Estas sustancias no son perjudiciales para la salud humana ni el medio ambiente
Diese Stoffe sind nicht schädlich für die menschliche Gesundheit noch Umwelt
Ces substances ne sont pas nocives pour la santé humaine ni pour l’environnement
Queste sostanze non sono nocive per la salute umana o per l’ambiente
Estas substâncias NÃO são prejudiciais para a saúde humana nem para o ambiente
Disse stoffer er IKKE skadelige for hverken menneskers sundhed eller for miljøet
Deze stoffen zijn NIET schadelijk voor de menselijke gezondheid of voor het milieu
Dessa ämnen är INTE skadliga för människors hälsa eller för miljön
Αυτές οι ουσίες ΔΕΝ είναι επιβλαβείς στην ανθρώπινη υγεία ή στο περιβάλλον
Тези вещества НЕ са вредни за човешкото здраве и за околната среда
Tyto látky NEJSOU škodlivé pro lidské zdraví ani pro životní prostředí
Need ained EI ole kahjulikud inimese tervisele ega keskkonnale
Ezek az anyagok NEM ártalmasak az emberi egészségre és a könyezetre
Šīs vielas NAV kaitīgas cilvēka veselībai vai videi
Šios medžiagos NĖRA žalingos žmonių sveikatai ar aplinkai
Substancje te NIE są szkodliwe dla zdrowia ani środowiska naturalnego
Aceste substanțe NU sunt nocive pentru sănătatea umană și nici pentru mediul înconjurător
Эти вещества НЕ вредны для здоровья человека и окружающей среды

PMML0569 rev.0 - 01/2021
IV
INDEX
1 GENERAL INFORMATION .................................................1
2 SAFETY................................................................................1
3 IMPORTANT NOTICE .........................................................2
4 NAME OF PARTS ................................................................3
5 BEFORE INSTALLATION....................................................3
6 INSTALLATION ....................................................................3
7 MAINTENANCE ...................................................................8
8 TEST RUN............................................................................9
9 ELECTRICAL WIRING ........................................................9
ÍNDICE
1 INFORMACIÓN GENERAL................................................. 11
2 SEGURIDAD ........................................................................11
3 AVISO IMPORTANTE .......................................................... 12
4 NOMBRES DE LAS PIEZAS............................................... 13
5 ANTES DE LA INSTALACIÓN ............................................13
6 INSTALACIÓN......................................................................13
7 MANTENIMIENTO...............................................................18
8 PRUEBA DE FUNCIONAMIENTO...................................... 19
9 CABLEADO ELÉCTRICO ...................................................19
INHALTSVERZEICHNIS
1 ALLGEMEINE INFORMATIONEN ...................................... 21
2 SICHERHEIT........................................................................ 21
3 WICHTIGER HINWEIS........................................................22
4 TEILEBEZEICHNUNG.........................................................23
5 VOR DER INSTALLATION.................................................. 23
6 INSTALLATION ....................................................................23
7 WARTUNG ...........................................................................28
8 TESTLAUF ...........................................................................29
9 KABELANSCHLUSS ...........................................................29
INDEX
1 INFORMATIONS GÉNÉRALES..........................................31
2 SÉCURITÉ............................................................................31
3 REMARQUES IMPORTANTES .......................................... 32
4 NOMENCLATURE DES PIÈCES........................................33
5 AVANT L’INSTALLATION.....................................................33
6 INSTALLATION ....................................................................33
7 MAINTENANCE ...................................................................38
8 TEST DE FONCTIONNEMENT .......................................... 39
9 CÂBLAGE ÉLECTRIQUE....................................................39
INDICE
1 INFORMAZIONI GENERALI............................................... 41
2 SICUREZZA .........................................................................41
3 NOTA IMPORTANTE ...........................................................42
4 NOMENCLATURA DEI COMPONENTI .............................43
5 PRIMA DELL’INSTALLAZIONE .......................................... 43
6 INSTALLAZIONE .................................................................43
7 MANUTENZIONE ................................................................ 48
8 PROVA DI FUNZIONAMENTO ...........................................49
9 COLLEGAMENTI ELETTRICI ............................................49
ÍNDICE
1 INFORMAÇÃO GERAL .......................................................51
2 SEGURANÇA....................................................................... 51
3 NOTA IMPORTANTE ...........................................................52
4 NOME DAS PEÇAS............................................................. 53
5 ANTES DA INSTALAÇÃO ...................................................53
6 INSTALAÇÃO.......................................................................53
7 MANUTENÇÃO....................................................................58
8 TESTE DE FUNCIONAMENTO..........................................59
9 LIGAÇÕES ELÉTRICAS .....................................................59
INDHOLDSFORTEGNELSE
1 GENEREL INFORMATION .................................................61
2 SIKKERHED......................................................................... 61
3 VIGTIG MEDDELELSE ....................................................... 62
4 NAVN PÅ DELE....................................................................63
5 FØR INSTALLATION ...........................................................63
6 INSTALLATION ....................................................................63
7 VEDLIGEHOLDELSE..........................................................68
8 TESTKØRSEL...................................................................... 69
9 ELEKTRISK LEDNINGSFØRING....................................... 69
INHOUDSOPGAVE
1 ALGEMENE INFORMATIE..................................................71
2 VEILIGHEID .........................................................................71
3 BELANGRIJKE MEDEDELING ..........................................72
4 NAMEN VAN ONDERDELEN .............................................73
5 VOOR DE INSTALLATIE.....................................................73
6 INSTALLATIE .......................................................................73
7 ONDERHOUD...................................................................... 78
8 PROEFDRAAIEN................................................................. 79
9 ELEKTRISCHE BEDRADING............................................. 79
INNEHÅLLSFÖRTECKNING
1 ALLMÄN INFORMATION ....................................................81
2 SÄKERHET .......................................................................... 81
3 VIKTIG ANMÄRKNING........................................................ 82
4 DELARNAS NAMN ..............................................................83
5 FÖRE INSTALLATION......................................................... 83
6 INSTALLATION ....................................................................83
7 UNDERHÅLL........................................................................ 88
8 PROVKÖRNING ..................................................................89
9 ELEKTRISK ANSLUTNING.................................................89
ΕΥΡΕΤΗΡΙΟ
1 ΓΕΝΙΚΕΣ ΠΛΗΡΟΦΟΡΙΕΣ.................................................. 91
2 ΑΣΦΑΛΕΙΑ............................................................................91
3 ΣΗΜΑΝΤΙΚΗ ΠΑΡΑΤΗΡΗΣΗ .............................................. 92
4 ΟΝΟΜΑΤΑ ΕΞΑΡΤΗΜΑΤΩΝ............................................... 93
5 ΠΡΙΝ ΕΓΚΑΤΑΣΤΑΣΗ...........................................................93
6 ΕΓΚΑΤΑΣΤΑΣΗ.....................................................................93
7 ΣΥΝΤΗΡΗΣΗ........................................................................98
8 ΔΟΚΙΜΑΣΤΙΚΟ ΤΡΕΞΙΜΟ...................................................99
9 ΗΛΕΚΤΡΙΚΗ ΚΑΛΩΔΙΩΣΗ ..................................................99
ИНДЕКС
1 ОБЩА ИНФОРМАЦИЯ....................................................... 101
2 БЕЗОПАСНОСТ..................................................................101
3 ВАЖНА БЕЛЕЖКА..............................................................102
4 НАЗВАНИЯ НА ЧАСТИТЕ .................................................103
5 ПРЕДИ ИНСТАЛАЦИЯ.......................................................103
6 МОНТАЖ.............................................................................. 103
7 ПОДДРЪЖКА ......................................................................108
8 ИЗПИТАТЕЛЕН ЦИКЪЛ.....................................................109
9 ЕЛЕКТРИЧЕСКО ОКАБЕЛЯВАНЕ ................................... 109
OBSAH
1 OBECNÉ INFORMACE.......................................................111
2 BEZPEČNOST.....................................................................111
3 DŮLEŽITÉ UPOZORNĚNÍ..................................................112
4 NÁZEV DÍLŮ ........................................................................ 113
5 PŘED INSTALACÍ................................................................113
6 INSTALACE..........................................................................113
7 ÚDRŽBA ...............................................................................118
8 ZKUŠEBNÍ CHOD................................................................119
9 ELEKTROINSTALACE ........................................................119

PMML0569 rev.0 - 01/2021
V
INDEKS
1 ÜLDTEAVE........................................................................... 121
2 OHUTUS...............................................................................121
3 TÄHTIS TEADE.................................................................... 122
4 OSADE NIMED ....................................................................123
5 ENNE PAIGALDAMIST .......................................................123
6 PAIGALDAMINE ..................................................................123
7 HOOLDUS............................................................................128
8 KATSETAMINE ....................................................................129
9 ELEKTRIÜHENDUSED.......................................................129
TARTALOMJEGYZÉK
1 ÁLTALÁNOS INFORMÁCIÓK ............................................. 131
2 BIZTONSÁG......................................................................... 131
3 FONTOS FIGYELMEZTETÉS ............................................132
4 RÉSZEK NEVE ....................................................................133
5 TELEPÍTÉS ELŐTT.............................................................133
6 TELEPÍTÉS .......................................................................... 133
7 KARBANTARTÁS.................................................................138
8 PRÓBAÜZEM....................................................................... 139
9 ELEKTROMOS KÁBELEZÉS .............................................139
INDEKSS
1 VISPĀRĪGA INFORMĀCIJA................................................ 141
2 DROŠĪBA.............................................................................. 141
3 SVARĪGA PIEZĪME.............................................................. 142
4 DETAĻU NOSAUKUMS.......................................................143
5 PIRMS UZSTĀDĪŠANAS.....................................................143
6 UZSTĀDĪŠANA ....................................................................143
7 TEHNISKĀ APKOPE ........................................................... 148
8 TESTA DARBĪBA..................................................................149
9 ELEKTROINSTALĀCIJA ..................................................... 149
INDEKSAS
1 BENDROJI INFORMACIJA.................................................151
2 SAUGUMAS ......................................................................... 151
3 SVARBI PASTABA...............................................................152
4 DALIŲ PAVADINIMAI...........................................................153
5 PRIEŠ MONTAVIMĄ............................................................153
6 MONTAVIMAS...................................................................... 153
7 TECHNINĖ PRIEŽIŪRA ...................................................... 158
8 TESTINIS PALEIDIMAS......................................................159
9 ELEKTROS LAIDAI .............................................................159
SPIS TREŚCI
1 INFORMACJE OGÓLNE.....................................................161
2 BEZPIECZEŃSTWO............................................................161
3 WAŻNE INFORMACJE........................................................162
4 CZĘŚCI SKŁADOWE ..........................................................163
5 PRZED INSTALACJĄ.......................................................... 163
6 MONTAŻ...............................................................................163
7 KONSERWACJA.................................................................. 168
8 ROZRUCH PRÓBNY...........................................................169
9 PODŁĄCZENIE ELEKTRYCZNE .......................................169
INDICE
1 INFORMAȚII GENERALE ...................................................171
2 SIGURANȚĂ.........................................................................171
3 OBSERVAȚIE IMPORTANTĂ ............................................. 172
4 DENUMIREA COMPONENTELOR .................................... 173
5 ÎNAINTE DE INSTALARE....................................................173
6 INSTALAREA........................................................................173
7 MENTENANȚĂ..................................................................... 178
8 PROBĂ DE FUNCȚIONARE...............................................179
9 CABLAJUL ELECTRIC........................................................ 179
ОГЛАВЛЕНИЕ
1 ОБЩАЯ ИНФОРМАЦИЯ....................................................181
2 БЕЗОПАСНОСТЬ................................................................181
3 ВАЖНОЕ ЗАМЕЧАНИЕ...................................................... 182
4 НАЗВАНИЕ ДЕТАЛЕЙ........................................................ 183
5 ПЕРЕД УСТАНОВКОЙ ....................................................... 184
6 УСТАНОВКА........................................................................184
7 ТЕХНИЧЕСКОЕ ОБСЛУЖИВАНИЕ..................................188
8 ПРОБНЫЙ ПУСК ................................................................ 189
9 ЭЛЕКТРОПРОВОДКА.........................................................189

PMML0569 rev.0 - 01/2021
VII
English
Specications in this manual are subject to change without notice in order that HITACHI may bring the latest innovations
to their customers.Whilst every e󰀨ort is made to ensure that all specications are correct, printing errors are beyond HI-
TACHI’s control; HITACHI cannot be held responsible for these errors.
Español
Las especicaciones de este manual están sujetas a cambios sin previo aviso a n de que HITACHI pueda ofrecer las
últimas innovaciones a sus clientes.
A pesar de que se hacen todos los esfuerzos posibles para asegurarse de que las especicaciones sean correctas, los
errores de impresión están fuera del control de HITACHI, a quien no se hará responsable de ellos.
Deutsch
Bei den technischen Angaben in diesem Handbuch sind Änderungen vorbehalten, damit HITACHI seinen Kunden die
jeweils neuesten Innovationen präsentieren kann.
Sämtliche Anstrengungen wurden unternommen, um sicherzustellen, dass alle technischen Informationen ohne Fehler
verö󰀨entlicht worden sind. Für Druckfehler kann HITACHI jedoch keine Verantwortung übernehmen, da sie außerhalb
ihrer Kontrolle liegen.
Français
Les caractéristiques publiées dans ce manuel peuvent être modiées sans préavis, HITACHI souhaitant pouvoir toujours
o󰀨rir à ses clients les dernières innovations.
Bien que tous les e󰀨orts sont faits pour assurer l’exactitude des caractéristiques, les erreurs d’impression sont hors du
contrôle de HITACHI qui ne pourrait en être tenu responsable.
Italiano
Le speciche di questo manuale sono soggette a modica senza preavviso a󰀩nché HITACHI possa o󰀨rire ai propri cli-
enti le ultime novità.
Sebbene sia stata posta la massima cura nel garantire la correttezza dei dati, HITACHI non è responsabile per eventuali
errori di stampa che esulano dal proprio controllo.
Português
As especicações apresentadas neste manual estão sujeitas a alterações sem aviso prévio, de modo a que
a HITACHI possa oferecer aos seus clientes, da forma mais expedita possível, as inovações mais recentes.
Apesar de serem feitos todos os esforços para assegurar que todas as especicações apresentadas são correctas, quais-
quer erros de impressão estão fora do controlo da HITACHI, que não pode ser responsabilizada por estes erros eventuais.
Dansk
Specikationerne i denne vejledning kan ændres uden varsel, for at HITACHI kan bringe de nyeste innovationer ud til kunderne.
På trods af alle anstrengelser for at sikre at alle specikationerne er korrekte, har HITACHI ikke kontrol over trykfejl, og
HITACHI kan ikke holdes ansvarlig herfor.
Nederlands
De specicaties in deze handleiding kunnen worden gewijzigd zonder verdere kennisgeving zodat HITACHI zijn klanten
kan voorzien van de nieuwste innovaties.
Iedere poging wordt ondernomen om te zorgen dat alle specicaties juist zijn. Voorkomende drukfouten kunnen echter
niet door HITACHI worden gecontroleerd, waardoor HITACHI niet aansprakelijk kan worden gesteld voor deze fouten.
Svenska
Specikationerna i den här handboken kan ändras utan föregående meddelande för att HITACHI ska kunna leverera de
senaste innovationerna till kunderna.
Vi på HITACHI gör allt vi kan för att se till att alla specikationer stämmer, men vi har ingen kontroll över tryckfel och kan
därför inte hållas ansvariga för den typen av fel.

PMML0569 rev.0 - 01/2021
VIII
Eλλhnika
Οι προδιαγραφές του εγχειριδίου μπορούν να αλλάξουν χωρίς προειδοποίηση, προκειμένου η HITACHI να παρέχει τις
τελευταίες καινοτομίες στους πελάτες της.
Αν και έχει γίνει κάθε προσπάθεια προκειμένου να εξασφαλιστεί ότι οι προδιαγραφές είναι σωστές, η HITACHI δεν μπορεί
να ελέγξει τα τυπογραφικά λάθη και, ως εκ τούτου, δεν φέρει καμία ευθύνη για αυτά τα λάθη.
Български
Спецификациите в това ръководство подлежат на изменения без известяване, така че HITACHI да може да
предоставя на своите клиенти последните иновации.
Полагат се всички усилия, за да се гарантира, че всички спецификации са коректни, но печатните грешки са извън
обсега на контрола на HITACHI и HITACHI не може да носи отговорност за тези грешки.
Čeština
Aby společnost HITACHI mohla svým zákazníkům poskytovat nejnovější inovace, specikace uvedené v této příručce
podléhají změnám bez předchozího upozornění.
Přestože vynakládáme maximální úsilí, aby všechny specikace byly správné, tiskové chyby nespadají pod kontrolu
společnosti HITACHI, která za takové chyby nenese odpovědnost.
Eesti
Käesoleva juhendi tehnilised kirjeldused võivad muutuda ilma ette teatamiseta, selleks et HITACHI saaks tuua oma
klientideni kõige uuemad innovatsioonid.
Kuigi püütakse tagada, et kõik tehnilised kirjeldused oleksid õiged, on trükivead väljaspool HITACHI kontrolli; HITACHI ei
vastuta nende vigade eest.
Magyar
Az alábbi kézikönyvben foglalt előírások előzetes értesítés nélkül változhatnak, annak érdekében, hogy a HITACHI a
legfrissebb újításokkal szolgálhasson ügyfelei számára.
Bár minden erőfeszítést megteszünk annak érdekében, hogy minden előírás helyes legyen, a nyomtatási hibák nem
állnak a HITACHI ellenőrzése alatt; ezekért a hibákért a HITACHI nem tehető felelőssé.
Latviešu
Šīs rokasgrāmatas specikācijas var mainīties bez brīdinājuma, lai HITACHI varētu saviem klientiem piedāvāt jaunākās
inovācijas.
Lai gan tiek pieliktas visas pūles, nodrošinot, ka visas specikācijas ir pareizas, drukāšanas kļūdas ir ārpus HITACHI
kontroles; HITACHI nevar būt atbildīga par šīm kļūdām.
Lietuvių
Šio vadovo specikacijos gali būti keičiamos be įspėjimo, kad „HITACHI“ galėtų pateikti savo klientams paskutines
naujoves.
Nors dedamos visos pastangos siekiant užtikrinti, kad visos specikacijos būtų teisingos, „HITACHI“ nekontroliuoja
spausdinimo klaidų; „HITACHI“ negali būti laikoma atsakinga už tokias klaidas.
Polski
Zamieszczone w niniejszej instrukcji obsługi dane techniczne mogą ulec zmianie bez uprzedniego powiadomienia ze
względu na innowacyjne rozwiązania, jakie rma HITACHI nieustannie wprowadza z myślą o swoich klientach.
Mimo podejmowanych starań, aby zapewnić poprawność wszystkich podanych tutaj informacji, nie można wykluczyć
zaistnienia błędów drukarskich, za które rma HITACHI nie ponosi żadnej odpowiedzialności.
Română
Specicațiile din acest manual pot  modicate fără noticare prealabilă, pentru ca HITACHI să poată pune la dispoziția
clienților noștri ultimele inovații.
Deși depunem toate eforturile pentru a ne asigura că toate specicațiile sunt corecte, erorile de tipărire depășesc
controlul HITACHI; HITACHI nu poate  tras la răspundere pentru aceste erori.
Русский
Технические характеристики, содержащиеся в данном руководстве, могут быть изменены HITACHI без
предварительного уведомления, по причине постоянного внедрения последних инноваций.
Несмотря на то, что мы принимаем все возможные меры для актуализации технических данных, при публикации
возможны ошибки, которые HITACHI не может контролировать, и за которые не несет ответственности.

PMML0569 rev.0 - 01/2021
IX
EN English Original Version
ES Español Versión traducida
DE Deutsch Übersetzte Version
FR Français Version traduite
IT Italiano Versione tradotta
PT Português Versão traduzidal
DA Dansk Oversat version
NL Nederlands Vertaalde versie
SV Svenska Översatt version
EL Ελληνικα Μεταφρασμένη έκδοση
EN English Original Version
BG Български Преведена версия
CS Čeština Přeložená verze
ET Eesti Tõlgitud versioon
HU Magyar Lefordított változat
LV Latviešu Tulkotā versija
LT Lietuvių Versta versija
PL Polski Tłumaczenie wersji oryginalnej
RO Română Versiune tradusă
RU Русский Переведенная версия
EN
The English version is the original one; other languages are
translated from English. Should any discrepancy occur between
the English and the translated versions, the English version shall
prevail.
ES
La versión en inglés es la original, y las versiones en otros idiomas
son traducciones de la inglesa. En caso de discrepancias entre la
versión inglesa y las versiones traducidas, prevalecerá la versión
inglesa.
DE
Die englische Fassung ist das Original, und die Fassungen in an-
deren Sprachen werden aus dem Englischen übersetzt. Sollten die
englische und die übersetzten Fassungen voneinander abweichen,
so hat die englische Fassung Vorrang.
FR
La version anglaise est la version originale; les autres langues
sont traduites de l’anglais. En cas de divergence entre les versions
anglaise et traduite, la version anglaise prévaudra.
IT
La versione inglese è l’originale e le versioni in altre lingue sono
traduzioni dall’inglese. In caso di divergenze tra la versione inglese
e quelle tradotte, fa fede la versione inglese.
PT
A versão inglesa é a original; as versões em outras línguas são
traduzidas do inglês. Em caso de divergência entre a versão em
língua inglesa e as versões traduzidas, faz fé a versão em língua
inglesa.
DA
Den engelske udgave er originalen, og udgaverne på andre sprog
er oversat fra engelsk. Hvis der forekommer uoverensstemmelser
mellem den engelske og den oversatte sprogudgave, vil den engel-
ske udgave være gældende.
NL
De Engelse versie is de originele; andere talen zijn vertaald uit het
Engels. In geval van verschillen tussen de Engelse versie en de
vertaalde versies, heeft de Engelse versie voorrang.
SV
Den engelska versionen är originalet, och versionerna på andra
språk är från engelska översättningar. I händelse av bristande
överensstämmelse mellan den engelska och den översatta ver-
sionerna, skall den engelska versionen vara giltig.
EL
Η αγγλική έκδοση είναι το πρωτότυπο και οι εκδόσεις σε
άλλες γλώσσες μεταφράζονται από τα αγγλικά. Σε περίπτωση
που διαπιστωθούν διαφορές μεταξύ της αγγλικής και της
μεταφρασμένης έκδοσης, η αγγλική έκδοση είναι επικρατέστερη.
BG
Версията на английски език е оригиналната; версиите на
останалите езици са в превод от английски език. При различие
между английската версия и преводна версия на друг език за
меродавна се счита английската версия.
CS
Originální verze tohoto dokumentu je v angličtině; ostatní jazykové
varianty jsou z angličtiny přeložené. Pokud mezi anglickou a ja-
koukoli jinou jazykovou verzí dojde k rozporu, bude převažovat
anglická verze.
ET
Originaalversioon on ingliskeelne; teised keeled on tõlge inglise
keelest. Vastuolude korral ingliskeelse ja tõlkeversioonide vahel
kehtib eesõiguslikult ingliskeelne versioon.
HU
Az eredeti változat az angol; az egyéb nyelvű változatok angolról
lettek fordítva. Amennyiben az angol és a fordított verziók között
bármilyen eltérés mutatkozik, az angol nyelvű változat a mérvadó.
LV
Angļu valodas versija ir oriģināla; citas valodas tiek tulkotas no
angļu valodas. Ja starp angļu valodu un tulkoto versiju rodas
jebkādas neatbilstības, noteicošais ir angļu valodas variants.
LT
Versija anglų kalba yra originali; versijos kitomis kalbomis yra
išverstos iš anglų kalbos. Jei yra neatitikimų tarp versijos anglų
kalba ir verstinių versijų, pirmenybė teikiama versijai anglų kalba.
PL
Wersja angielska jest wersją oryginalną - wszystkie pozostałe
stanowią jej tłumaczenie na odpowiednie języki. W przypadku
stwierdzenia jakichkolwiek rozbieżności między oryginałem a jego
tłumaczeniem, rozstrzygająca jest wersja w języku angielskim.
RO
Versiunea originală este cea în limba engleză; versiunile în alte
limbi sunt traduse din limba engleză. Dacă există vreo discrepanță
între versiunile în limba engleză și versiunea tradusă, prevalează
versiunea în limba engleză.
RU
Английская версия является оригинальной; другие языки
переведены с английского. В случае любого расхождения
между английской и переведенной версиями, английская
версия имеет преимущественную силу.

1 GENERAL INFORMATION
1.1 GENERAL NOTES
No part of this publication may be reproduced, copied, led
or transmitted in any shape or form without the permission of
Johnson Controls-Hitachi Air Conditioning Spain, S.A.U.
Within the policy of continuous improvement of its products,
Johnson Controls-Hitachi Air Conditioning Spain, S.A.U.
reserves the right to make changes at any time without prior
notication and without being compelled to introducing them into
products previously sold. This document may therefore have
been subject to amendments during the life of the product.
HITACHI makes every e󰀨ort to o󰀨er correct, up-to-date
documentation. Despite this, printing errors cannot be controlled
by HITACHI and are not its responsibility.
As a result, some of the images or data used to illustrate this
document may not refer to specic models. No claims will be
accepted based on the data, illustrations and descriptions
included in this manual.
No type of modication must be made to the equipment without
prior, written authorisation from the manufacturer.
2 SAFETY
2.1 SYMBOLS USED
During normal air conditioning system design work or unit
installation, greater attention must be paid in certain situations
requiring particular care in order to avoid injuries and damage to
the unit, the installation or the building or property.
Situations that jeopardise the safety of those in the surrounding
area or that put the unit itself at risk will be clearly indicated in
this manual.
To indicate these situations, a series of special symbols will be
used to clearly identify these situations.
Pay close attention to these symbols and to the messages
following them, as your safety and that of others depends on it.
!DANGER
• The text following this symbol contains information and
instructions relating directly to your safety, in addition to
hazards or unsafe practices which could result in severe
personalinjuriesordeath.
• Nottakingtheseinstructionsintoaccountcouldleadtoserious,
very serious or even fatal injuries to you and others in the
proximitiesoftheunit.
In the texts following the danger symbol you can also nd
information on safe procedures during unit installation.
!CAUTION
• Thetextfollowingthissymbolcontainsinformationandinstructions
relating directly to your safety, in addition to hazards or unsafe
practices which could result in minor personal injury or product or
propertydamage.
• Nottakingtheseinstructionsintoaccountcouldleadtominorinjuries
toyouandothersintheproximitiesoftheunit.
• Nottakingtheseinstructionsintoaccountcouldleadtounitdamage.
In the texts following the caution symbol you can also nd
information on safe procedures during unit installation.
?NOTE
• Thetextfollowingthissymbolcontainsinformationorinstructionsthat
maybeofuseorthatrequireamorethoroughexplanation.
• Instructionsregardinginspectionstobemadeonunitpartsorsystems
mayalsobeincluded.
GENERAL INFORMATION
PMML0569 rev.0 - 01/2021
1
EN

2.2 ADDITIONAL INFORMATION ABOUT SAFETY
!DANGER
• HITACHIisnotabletoforeseeallthecircumstanceswhichmay
resultinapotentialdanger.
• Donotpourwaterintheindoororoutdoorunit.Theseproducts
arettedwithelectriccomponents.Ifwatercomesintocontact
with electric components, this will cause a serious electric
shock.
• Donothandleoradjustthesafetydevicesinsidetheindoorand
outdoorunits.Thehandlingoradjustmentofthesedevicesmay
resultinseriousaccident.
• Donotopentheservicecoveroraccesspaneloftheindoorand
outdoorunitswithoutdisconnectingthemainsupply.
• In the event of re, switch off the mains, put out the re
immediatelyandcontactyourservicesupplier.
• Checkthattheearthcableiscorrectlyconnected.
• Connecttheunittoacircuitbreakerofthespeciedcapacity.
!CAUTION
• Refrigerantleaksmayhinderrespirationasthegasdisplacestheair
intheroom.Itisassumedthatthisheatpumpairconditionerwillbe
operatedandservicedbyEnglishspeakingpeople.Ifthisisnotthe
case,thecustomershouldbeaddsafety,cautionandoperatingsigns
inthenativelanguage.
• Fittheindoorunit,theoutdoorunit,theremotecontrolandthecable
ataminimumof3metresawayfromsourcesofstrongradiationfrom
electromagneticwaves,suchasmedicalequipment.
• Donotusesprays,suchasinsecticides,varnishesorenamelsorany
otherinammablegaswithinametreofthesystem.
• Ifthecircuitbreakerorsupplyfuseoftheunitcomesonfrequently,
stopthesystemandcontacttheservicesuppler.
• Donotcarryoutmaintenanceorinspectionworkyourself.Thiswork
mustbecarriedoutbyqualiedservicepersonnelwithsuitabletools
andresourcesforthework.
• Donotplaceanyforeignmaterial (branches, sticks, etc.) in the air
inletoroutletoftheunit.Theseunitsarettedwithhighspeedfans
andcontactwithanyobjectisdangerous.
• This appliance must be used only by adult and capable people,
havingreceivedthetechnicalinformationorinstructionstohandlethis
applianceproperlyandsafely.
• Childrenshouldbesupervisedtoensurethattheydonotplaywith
theappliance.
• Installtheunitinaplacenotaccessiblebythegeneralpublic.
?NOTE
• Theairintheroomshouldberenewedandtheroomventilatedevery
3or4hours.
• The system tter and specialist shall provide anti-leak safety in
accordancewithlocalregulations.
• The installer and system specialist shall secure safety against the
refrigerantleakageaccordingtolocalregulationsorstandards.The
following standards may be applicable, if local regulations are not
available.InternationalOrganizationforStandardization,ISO5149or
EuropeanStandard,EN378orJapanStandard,KHKS0010.
• Electrical wiring must comply with national and local regulations.
Contactyourlocalauthorityinregardstostandards,rules,regulations,
etc.
3 IMPORTANT NOTICE
This air conditioner has been designed for standard air
conditioning for human beings. For use in other applications,
please contact your HITACHI dealer or service contractor.
The air conditioning system should only be installed by qualied
personnel, with the necessary resources, tools and equipment,
who are familiar with the safety procedures required to
successfully carry out the installation.
The supplementary information about the purchased products
is supplied in a CD-ROM, which can be found bundled with the
outdoor unit. In case that the CD-ROM is missing or it is not
readable, please contact your HITACHI dealer or distributor.
PLEASE READ THE MANUAL AND THE FILES ON THE
CD-ROM CAREFULLY BEFORE STARTING WORK ON THE
INSTALLATION OF THE AIR CONDITIONING SYSTEM.
Failure to observe the instructions for installation, use and
operation described in this documentation may result in
operating failure including potentially serious faults, or even the
destruction of the air conditioning system.
It is assumed that the air conditioning system will be installed
and maintained by responsible personnel trained for the
purpose. If this is not the case, the customer should include all
the safety, caution and operating signs in the native language of
the personnel responsible.
Do not install the unit in the following places, as this may lead to
a re, deformities, rusting or faults:
• Places where oil is present (including oil for machinery).
• Places with a high concentration of sulphurous gas, such as
spas.
• Places where ammable gases may be generated or
circulate.
• Places with a saline, acidic or alkaline atmosphere.
Do not install the unit in places where silicon gas is present. Any
silicon gas deposited on the surface of the heat exchanger will
repel water. As a result, the condensate water will splash out
of the collection tray and into the electrical box. Water leaks or
electrical faults may eventually be caused.
Do not install the unit in a place where the current of expelled
air directly a󰀨ects animals or plants as they could be adversely
a󰀨ected.
There are detailed information about unit installation, service
space, wiring diagrams, electrical connection, refrigerant charge,
in the corresponding chapter, please read the corresponding
chapter carefully before starting work on the installation.
IMPORTANT NOTICE
PMML0569 rev.0 - 01/2021
2

4 NAME OF PARTS
DRAIN
>PS<
HS-HB
DIP
Air panel P-N23NA2 /
P-AP160KA3
Air inlet grille Air inlet Air outlet Cover for corner pocket
5 BEFORE INSTALLATION
5.1 FACTORY-SUPPLIED ACCESSORIES
!CAUTION
Whentheair panel isunpacked,placeitoninsulationmaterial,etc. to
protectthesealinginsulationfromscratches.
Check to ensure that the accessories are packed with the air
panel.
Accessory P-N23NA2
P-AP160KA3 Purpose
Long Screw
(M6 Cross
Screw)
4For xing air panel
If any of these accessories are not packed in the packing,
please contact your contractor.
6 INSTALLATION
6.1 CHECK THE INDOOR UNIT HEIGHT FROM THE FALSE CEILING SURFACE
Check the distance between the indoor unit and the false ceiling.
It is 12+5mm as shown below.
12+5
0
Ceiling surface
Indoor unit
If not, adjust the distance by using the checking scale with
maintaining the levelness of the indoor unit.
NAME OF PARTS
PMML0569 rev.0 - 01/2021
3
EN

6.2 REMOVING AIR INTAKE GRILLE FROM AIR PANEL
1 Push both ends of knobs at the air inlet grille toward the
arrow direction, open the air inlet grille until the angle of
approximately 45° from the air panel surface. After lifting
the air inlet grille keeping it inclined, draw the air inlet grille
forward. (Remove the lament tape (4 portions) xing the air
lter).
P-AP160NAE
P-AP160NA1
45°
45°
Knob
Air inlet grille
Corner
pocket cover
(4 portions)
Air panel
Supporting string
2 Lift the grille keeping it inclined.
3 Draw the grille towards the open space after lifting.
?NOTE
Perform the attaching work in the reverse procedure of removing for
installtheairintakegrille.Theairinletgrillecanbeattachedfromany
4directionsbyrotatingit.Theairintakegrilledirectioncanbeselected
freely.
6.3 INSTALLING AIR PANEL
1 Remove the cover of the corner pocket (4 portions). Remove
pulling A part toward the arrow direction.
A
2 Pull down the U-shaped hook (at 2 positions) located at the
indoor unit side.
3 Mount the air panel temporarily. Fit the corner position of the
refrigerant pipe connection at the indoor unit and the position
stamped as “Ref. Pipe ”. Then, catch the C-shaped hinges (2
portions) onto the U-shaped hooks (2 portions).
4 Fix the air panel to the xing plate by factory supplied long
screws (M6 cross screws).
Long screws (Q'ty 4)
C-shaped hinge
Stamp refrigerant
pipe
Electrical box
Refrigerant pipe
connections
Indoor unit
Air panel
U-shaped hook
Fixing plate
INSTALLATION
PMML0569 rev.0 - 01/2021
4

5 Tighten the long screws until touching the stopper to the
xing plate. Check to ensure that the distance between the
xing plate undersurface and the corner panel undersurface
is 26mm.
6 When tightening the long screws to prevent air leakage
and to be no gap between the false ceiling surface and
the indoor unit, the inner circumference of the air panel
(the position to attach the air inlet grille) may be slightly
deformed. However, it is not abnormality.
26
12
+5
0
False ceiling
Indoor unit
Fixing plate
(indoor unit)
Long screw
Corner
panel
!CAUTION
• Iftighten longscrews insufcient, maycause something wrongas
below.
Air Leakage
Smudge Dewing
• Ifanygaphaseventhoughtightenlongscrewssufcient,readjust
theheightofindoorunit.
No gap shall exist
• It’s able to adjust the indoor unit height by using wrench from the
cornerpocket.
Wrench
• Tooconsiderableadjustmentofheightcausedewingfromdrain-pan.
• Donotturntheairlouverbyhand.Ifmoved,thelouvermechanism
wouldbedamaged.
6.4 ATTACHMENT OF CORNER POCKET COVER
Attach the corner pocket covers after the air panel is mounted
completely.
a. Catch the band at the rear side of the corner pocket
cover onto the projection at the air panel as shown.
A
B
Projection
Fixing hook
Band
Fixing hook
b. Insert and push the xing hooks (2 portions) at Ⓐto the
air panel and insert and push the xing hook (1 portion)
at Ⓑto the air panel.
B
A
A
INSTALLATION
PMML0569 rev.0 - 01/2021
5
EN

6.5 ATTACHMENT OF CORNER POCKET COVER WITH MOTION SENSOR PS-MSK2 ON THE
AIR PANEL MODEL P-N23NA2
?NOTE
• Do not install the motion sensor kit PS-MSK2 (optional) in the
followingplaces.
• Itmaycausemisdetection,undetectableofmotionorthedeterioration
ofthemotionsensor.
aPlaceswhereambienttemperaturechangesdrastically.
bPlaceswhereexcessiveforceorvibrationisappliedtothe
motionsensor.
cPlaceswherestaticelectricityorelectromagneticwavesmay
generate.
dPlaceswhereisinterferenceforinfraredlightsuchasglassesor
mistinadetectingarea.
ePlaceswherethelensformotionsensorisexposedinhigh
temperatureandhumidityforalongtime.
f Placeswhereuidandcorrosivegasexist.
gPlaceswheredirectlightssuchassunlightorheadlightaffect
themotionsensor.
hPlaceswherehotairfromaheater,etc.affectsdirectlythe
motionsensor.
i Placeswhereweatheraffectsdirectlythesurfaceofthemotion
sensor.
j Placeswherethelenssurfacemaysmudgeorbedamaged
suchasadustyenvironment.
• Payattentionthatthedetectingfunctionwillbedecreasedifthelens
formotionsensorsmudges.
• In this case, wipe off smudges by a cotton swab soaked alcohol
(Isopropylalcoholisrecommended)orasoftcloth.
• Whenwipingoffsmudgesonthelensformotionsensor,donotapply
excessiveforce.
• Ifexcessiveforceisapplied,theresinlensmaybedamagedsothat
maycausemalfunctionssuchasmisdetectionorundetectableofthe
motion.
The corner pocket cover with motion sensor can be attached to
any of corners. Determine the attaching place as user’s request.
a. Connect the relay wire (attached in the air panel) to
CN10 in the electrical box.
Plastic band
Air panel
Corner pocket
Projection
Band
Corner pocket cover
with motion sensor
Relay wire
Plastic band
Wiring cover
Relay
connector
Run the relay wire to the corner pocket cover with motion sensor
through the top of xing plate for the indoor units. Set a length of
100mm to 200mm from the indoor unit to the relay connector.
100~200mm
Relay connector
Fixing plate
Relay wire
Indoor unit wiring
connection
Clamp the extra length of the relay wire by the plastic band and
store it at inside the ceiling.
b. Draw out the relay wire from the corner pocket of the air
panel. Connect the wiring for motion sensor at the corner
pocket cover to the relay connector. After connecting,
cover the relay connector connection by the wiring cover
and x the wiring cover by the plastic bands.
c. Catch the band at the rear side of the corner pocket
cover with motion sensor onto the projection at the air
panel.
d. While pushing the wiring into the corner pocket, insert
the xing hooks (2 portions) at Ⓐ to the square hole at
the air panel, and push the corner pocket cover. Then,
insert and push the xing hook (1 portion) at Ⓑto the
square hole at the air panel.
?NOTE
• Catchsecurelythebandontotheprojection.Ifnot,thecomerpocket
covermayfalldownwhenremovingitsothatmaycauseinjury.
• Catchsecurelythexinghooksofthecornerpocketcovertotheair
panel.Ifnot,thexinghookswillbedamaged.
INSTALLATION
PMML0569 rev.0 - 01/2021
6

6.6 CONTROL SETTINGS AFTER INSTALLING CORNER COVER WITH MOTION SENSOR
(PC-ARFP1E EXAMPLE)
Depending on the location of the corner with motion
sensor, setting on the wired controller is also necessary.
1 Press and hold “Menu” and “Back/Help” simultaneously for
at least three seconds with power applied and the indoor unit
is not operating. The Test Run menu will be displayed.
OK Back
Test Run Menu
Function 5
Input/Output
Thermistor Selection
Function Selection 01
/
03
Test Run
Entr RtrnSel.
2 Select “Function Selection” from the Test Run menu and
press “OK”.
3 Select the indoor unit by pressing “ ” and press “OK”.
Note: (This screen is NOT displayed when only one indoor
unit is connected to the wired controller. In this case, move
to 4.)
OK Back
Function Selection
01-01
All
01-02
01-03
01-04
Entr RtrnSel.
4 Press “ ” and select "L1".
OK Back
Function Selection:01-03
01
17
b1 00
b2 00
b3 00
b4 00
b5 00
Item Setting
/
Adj. Entr RtrnSel.
Set "L1" according to the table below by pressing " "
and press "OK".
When the products are shipped, the menu key should be
set to "L1=00", which indicates motion sensor is located at
stamp A.
Figure without corner covers
Do not install in the "Stamp C" position
Attached
location (as
shipped)
Stamp D Stamp A
Stamp C Stamp B
Refrigerant pipe
connection
L1 Attaching Place (Stamp)
00 A [No Setting Required]
01 B
02 Not Available
03 D
6.7 WIRING CONNECTION FOR AIR PANEL
1 The following connectors are used in the air panel. Remove
the tape xing the wiring connectors on the air panel and pull
out them as shown in the gure below. Connect them with
the wiring connectors on the indoor unit.
>PS<
HS-HB
Electrical box
Motor wiring for auto louver (on
air panel) (connector for low
voltage: 18 poles, white)
Motor wiring for auto louver (on
indoor unit) (Connector for low
voltage: 18 poles, white)
Condition without air
intake grille
2 After completing the wiring connection of the air panel,
attach the air inlet grille. Perform the attaching work in the
reverse procedure of removing.
INSTALLATION
PMML0569 rev.0 - 01/2021
7
EN

7 MAINTENANCE
When the indication, “FILTER” is shown on the display of the
remote control switch, take out the air lter according to the
indicated steps for each unit.
Do not operate the system without the air lter to protect the
indoor unit heat exchanger against being clogged.
Turn OFF the main power switch before taking out the lter.
(The previous operation mode may appear).
7.1 TAKE OUT THE FILTER
1 Open the air inlet grille after pushing the two knobs toward
the arrow mark.
Knob
Air inlet grille
2 Hold the lower side of the air inlet grille keeping it inclined.
Remove the hooks of air lter from the air inlet grille and
remove the air lter.
Hook
Upper part of lter
Lower part of lter
Air inlet grille
Air lter
Hook
7.2 CLEAN THE FILTER
Clean the air lter according to the following steps:
1 Use a vacuum cleaner or let water ow onto the air lter for
removing the dirt from the air lter.
!CAUTION
Donotusehotwaterhigherthanapproximately40ºC.
2 Dry the air lter in the shade after shaking o󰀨 moisture.
3 Do not use cleaner or other chemicals.
4 After the air lter is dried, attach and close correctly to the air
inlet grille.
7.3 RESET OF FILTER INDICATION
After cleaning the air lter, reset the lter sign according the remote control procedure.
MAINTENANCE
PMML0569 rev.0 - 01/2021
8

8 TEST RUN
!DANGER
• Do not put any foreign materials within the air inlet grille
operationrange.Itmayleadtoinjuryordamage.
• Keepthewirefromreorsharpedge.Breakingwiremaycause
ofinjuryduetoairinletgrilleorairlterfalling.
• Iftheairinletgrilleortheairlterfalls,itmaycauseinjury.
1 After completing installation of the air panel, Test Run should
be performed according to installation and maintenance
manual for the indoor unit.
2 Perform the checking work for the louver during the test run.
Do not move the louver by hand. If moved, the auto-swing
mechanism will be damaged.
a. Press “ ” (run / stop), and the operation is started.
Select the air ow direction by “ “ or “ ”.
b. The louver angle is changed by pressing “ ” or “ ”.
LCD Indication
The auto swing operation will be started to select “ ”
(auto swing). At this time, LCD indication displays the swing
repeatedly.
3 If there is a louver that does not move, check the connection
of the louver wiring connector (CN17).
?NOTE
• Adequate and optimal airow is dependent on application and
installationpractices which include positioningofofce equipment,
roomstructure,andofcecubicleorfurniturelayout.Adjustairow
formaximumcomfort.
• Thepositionofthelouversmaynotcoincidewiththelouverposition
indicatorontheLCD during auto swing operation.When adjusting
thelouverangle,setitaccordingtothelouverpositionontheLCD.
• Evenifthe“ ”or“ ”arepressedtostoptheautoswingfunction,the
louverisnotstoppedimmediately.
• Ifthecoolingoperationisperformedwithgreaterthan80%relative
humidity,condensationmayformontheairpanelorlouversurfaces.
9 ELECTRICAL WIRING
!CAUTION
• All electrical installation work must be performed by certied
personnelandallworkmustbecompleteandconformtolocaland
NEC (National Electrical Code) standards. Failure to uphold these
standardscanresultindamage,re,electricalshock,andseriousor
fatalinjury.
• Whenopeningand closing theelectricalboxcover, work sothatit
doesnotcontactthesuspensionwire.Ifthesuspensionwirebreaks,
theairinletgrilleandairltermayfall.Itmaycauseinjury.
• Performsecurelytheelectricalwiringwork.Iftheelectricalworkisnot
completed,heatgenerationattheconnection,areoranelectrical
shockmayoccur.
• Makesurethatthewiresaresecurelyxedinordernottoapplyan
externalforcetotheterminalconnectionsofthewirings.Ifxingisnot
completed,heatgenerationorarewilloccur.
1 The air panel has motor wiring for auto louver. Remove the
tape securing the wiring and make sure to pass it through
the cable band as shown in the gure on the right before
connecting it to the connector (CN17) on the PCB.
2 After connecting the connector, tighten the cable band
to secure the wiring. After wiring is secured, attach the
electrical box cover.
3 The following connectors are used in the air panel. Remove
the tape xing the wiring connectors on the air panel and pull
out them as shown in the gure below.
4 Connect them with the wiring connectors to CN17 in the
electrical box as the following gure.
CN37
IC1
CN9
DSW9
21

ON
8
7
123456
3
4
5
RSW1
6
2
DSW6
8
7
3
2
1
4
5
0
9
6
21

9
RSW2
0
1

DSW5 CN11
CN17
HA
CN10
CN6
CN33
CN3 CN4CN14
THM5
CN5
LED6
CN28
CN2
THM4
LED1
Motor wiring for auto
louver (on air panel)
Cable band
Connector
(CN17)
!DANGER
• Beforetheelectricalwiringwork,turnOFFthepowersource.If
the connectors are connected without turning OFF the power
source,theautoswinglouvercannotactivate.
• AirpanelP-AP160KA3:Incaseofattachingthisairpanelonthe
RCI-FSRseriesindoorunit,removetherelaywiringattachedto
indoorunitPCB.Afterthat,connectthewiringattachedtotheair
paneldirectlytothePCBasdescribedabove.
TEST RUN
PMML0569 rev.0 - 01/2021
9
EN