Hitachi SJ100 Series Owner's manual

SJ100 Series Supplemental Sheet (NBM585XA-12)
ATTENTION
Note 1:
The revision level of the MFG No. distinguishes the following changes in Function Codes A81, C31
and C32. The Inverter MGF No. is shown on the Specification Label (Nameplate), located on the right
side of the housing. The changes apply to inverters, which carry a revision code per the table below.
When you copy parameters between units manufactured before and after this change with a copy unit,
confirm Function Codes C31 and C32.
Example of MFG No. :
112H T123451J001
Revision
A…K…1A…1K…2A…2H…
Revision Increment--------Æ
Page Changes
3-18
Inverter Models Revision
before change
Applied
Revision
SJ100-002NFU 2E 2H
SJ100-004-022NFU 2G 2H
SJ100-037LFU 2E 2H
SJ100-055,075LFU K M
SJ100-004HFU 2F 2H
SJ100-007-040HFU 2G 2H
SJ100-055,075HFU L M
OLD DEFAULT SETTING:
“A” Function Run- Defaults DOP,DRW,DOP+
Func.
Code Name Description
time
Edit
EU/
US Units Func. Code Name
A81 AVR function
select
Automatic (output) voltage
regulation, selects from three
types of AVR functions, three
option codes:
00…AVR enabled
01…AVR disabled
02…AVR enabled except
during deceleration
02 - F-03 AVR
MODE
NEW DEFAULT SETTING:
*Inverters manufactured after the revision as defined in Note 1 will have the following settings:
“A” Function Run- Defaults DOP,DRW,DOP+
Func.
Code Name Description
time
Edit
EU/
US Units Func. Code Name
A81 AVR function
select
Automatic (output) voltage
regulation, selects from three
types of AVR functions, three
option codes:
00…AVR enabled
01…AVR disabled
02…AVR enabled except
during deceleration
00 - F-03 AVR
MODE
1/2
NBM585XA-12

Page Changes
3-32
B-7
OLD DEFAULT SETTING:
“C” Function Run- Defaults DOP,DRW,DOP+
Func.
Code Name Description
time
Edit
EU/
US Units Func. Code Name
C31 Reserved Factory use only; do not
change
00 - F-35 OUT-TM
O/C-1
C32 Terminal 11
active state
Select logic convention, two
option codes:
00…normally open [NO]
01…normally closed [NC]
00 - F-35 OUT-TM
O/C-2
NEW DEFAULT SETTING:
*Inverters manufactured after the revision as defined in Note 1 will have the following settings:
“C” Function Run- Defaults DOP,DRW,DOP+
Func.
Code Name Description
time
Edit
EU/
US Units Func. Code Name
C31 Terminal 11
active state
Select logic convention, two
option codes:
00…normally open [NO]
01…normally closed [NC]
00 - F-35 OUT-TM
O/C-1
C32 Terminal 12
active state
Select logic convention, two
option codes:
00…normally open [NO]
01…normally closed [NC]
00 - F-35 OUT-TM
O/C-2
OLD DEFAULT SETTING:
“C” Group Parameters Default Setting User Setting
Func. Code Name -FE(Europe) -FU(USA)
C31 Factory-set - -
C32 Terminal 11 active state 00 00
NEW DEFAULT SETTING:
*Inverters manufactured after the revision as defined in Note 1 will have the following settings:
“C” Group Parameters Default Setting User Setting
Func. Code Name -FE(Europe) -FU(USA)
C31 Terminal 11 active state 00 00
C32 Terminal 12 active state 00 00
2/2
NBM585XA-12