HM Electronics NEXEO HDX AC70 User manual
Quick Start Guide
HM ELECTRONICS, INC.
2848 Whiptail Loop, Carlsbad, CA 92010 USA
Phone: 1-800-848-4468 Fax: 858-552-0172
HME# PUB - 00071
Rev B 02/1/22
NEXEO | HDX™ AC70 SMART BATTERY CHARGER
The NEXEO | HDX™ AC70 Smart Battery Charger can
charge up to four BAT70 lithium-ion batteries simulta-
neously. LEDs at the charging ports indicate battery sta-
tus. Charge time is approximately two hours. The AC70
can be placed on a desktop or mounted on a wall.
TOOLS/EQUIPMENT REQUIRED (wall mounting only)
• Drill and drill bits (~ 3/16th inch (4.76 mm))
• Screwdriver (Phillips #2)
• Marker/punch, Safety Glasses
INSTALLATION/SETUP AND OPERATION
Desktop instructions:
1. Place the AC70 on a level desktop or shelf.
2. Connect the power adapter to a wall outlet and the
other end to the AC70 (see Fig. 3).
3. Position the BAT70 battery correctly for insertion
into the AC70 (it is keyed so it will only insert one
way, do not force fit).
4. Insert the BAT70 battery into a vacant port to begin
charging. LED activity indicates battery status (see
table below).
Battery Charger LED Reference Table
LED Color Status/Description
Green Flashing Green = Charging
Solid Green = Fully charged
Red Flashing Red = Incompatible battery
Red/Yellow Flashing Red & Yellow= Fault condition
Base Station HOME screen
Note: The AC70 requires close physical proximity
(<10 ft (3 m)) to the base station if you desire to mon-
itor battery status via the base station HOME screen.
When within range, the indicator on the
HOME screen changes from to (gray to green).
Once green, tap to view battery status.
Wall mounting instructions are found on page 2.
Mounting
Keyholes
Power
Connector
AC70 BATTERY CHARGER
Rear View
Battery
Storage
Ports (x4)
Note: Storage Ports do not charge batteries
Fig. 3
Fig. 2
Fig. 1
* Batteries are not included
1 2 3 4
HME
WALL OUTLETAC70 BATTERY CHARGER
Front/Top View
POWER ADAPTER
Note: Only use the HME approved Power Adapter provided.
Storage ports do not charge batteries.
Charging
Ports (x4)
on top
Storage
Ports (x4)
on side
©2022 HM Electronics, Inc. All rights reserved.
2
CHANGING POWER SUPPLY ADAPTER
1. Replace power adapter (P/N: CON-00004) to
match your country's outlet using your thumb and
forefinger to squeeze the latch (see Fig. 4).
2. While squeezing the latch, slide the adapter out,
away from the power supply to remove.
3. Release the latch and slide the appropriate adapter
on until it bottoms out and the latch clicks to secure
it in place.
Press in here on both sides of latch to release
Slide in these directions to remove and replace
Latch
Adapter
Fig. 4
TECHNICAL SPECIFICATIONS
Power Supply: Wall plug with switchable adapters
Input Voltage: Universal 100 - 240 VAC nominal
Output Voltage: 5V; 4A
MTBF: 300,000 hours calculated
AC70 Battery Charger
Input Voltage: 5V; 4A
Charge Output: ~ 3W per port
Temperature
Operating: 32°F to +104°F (0°C to +40°C)
Storage: 4°F to +176°F (-20°C to +80°C)
Humidity Range (non-condensing)
Storage: 0% -95%
Dimensions
5.09” L x 3.64” W x 1.84” H
(129.2 x 92.4 x 46.7 mm)
Weight
0.373 lb (0.169 kg)
Wireless PAN
2.4 GHz Wireless Technology
A copy of this guide and additional information including Regulatory,
Compliance, and Safety information can be found under NEXEO | HDX by
scanning this QR code or going to:
https://www.hme.com/qsr/drive-thru-user-manuals/
The HME logo and product names are registered trademarks or
trademarks of HM Electronics, Inc.
2”
(50.8 mm)
Wall Mounting Template for AC70
1. Hold template against the wall,
2. Use a marker to punch through the paper
template at the two crosshairs to mark the
wall.
3. Drill two holes at the marks on the wall (avoid
electrical or plumbing obstructions).
4. Install the provided hardware but do not
tighten. Leave a gap (~ ¹/8th inch (3.2 mm))
between the screw heads and wall.
5. Align the AC70 mounting keyholes with the two
screw heads (Fig. 2).
6. Mount the AC70 over the screw heads until
flush against the wall, then slide it down onto
the screw shanks to secure it in place.
