HME DX200 User manual

HME# 400G579
Rev E 3/19/08
DX200
Wireless Intercom
Operating Instructions

Table of Contents
SECTION 1. INTRODUCTION ....................................................................................................................1
EQUIPMENT IDENTIFICATION....................................................................................................................2
MAIN EQUIPMENT FEATURES ....................................................................................................................3
Beltpac Features .............................................................................................................................................3
WH200 Headset Features...............................................................................................................................3
Speaker Station Features ................................................................................................................................4
Base Station Features .....................................................................................................................................5
SECTION 2. EQUIPMENT SETUP..............................................................................................................6
BATTERY CHARGER SETUP ........................................................................................................................6
Connect AC Power Supply.............................................................................................................................6
Charge Batteries .............................................................................................................................................6
BASE STATION SETUP...................................................................................................................................7
Equipment Connections..................................................................................................................................7
Multiple Base Stations....................................................................................................................................8
Base Station Initialization...............................................................................................................................8
BELTPAC / WH200 HEADSET / SPEAKER STATION SETUP AND REGISTRATION ..............................11
Set Up Beltpacs ............................................................................................................................................11
Register Beltpacs..........................................................................................................................................11
Set Up WH200 Headsets..............................................................................................................................13
Register WH200 Headsets............................................................................................................................13
Set Up Speaker Stations ...............................................................................................................................15
Register Speaker Stations.............................................................................................................................17
INTERCOM AND AUXILIARY EQUIPMENT SETUPS .............................................................................20
2-Wire Intercom ...........................................................................................................................................20
4-Wire Intercom ...........................................................................................................................................20
Auxiliary Equipment ....................................................................................................................................21
8-Ohm Speaker.............................................................................................................................................21
SECTION 3. EQUIPMENT OPERATION................................................................................................22
BASE STATION OPERATION......................................................................................................................22
BELTPAC OPERATION.................................................................................................................................24
WH200 HEADSET OPERATION...................................................................................................................26
SPEAKER STATION OPERATION...............................................................................................................28
SECTION 4. TROUBLESHOOTING .........................................................................................................31
SECTION 5. TECHNICAL DATA..............................................................................................................32
EQUIPMENT SPECIFICATIONS ..................................................................................................................32
Base Station..................................................................................................................................................32
Beltpac..........................................................................................................................................................33
WH200 Headset............................................................................................................................................33
Speaker Station.............................................................................................................................................33
BLOCK DIAGRAM ........................................................................................................................................34
DX200 Base Station.....................................................................................................................................34
© 2008 HM Electronics, Inc.
The HME logo and product names are registered trademarks of HM Electronics, Inc. All rights reserved.
Illustrations in this publication are approximate representations of the actual
equipment, and may not be exactly as the equipment appears.
HM Electronics, Inc. is not responsible for equipment malfunctions due to
erroneous translation of its publications from their original English version.

FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communication. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct the interference
at his own expense.
Changes or modifications not expressly approved by HM Electronics, Inc. could void the users authority
to operate this equipment.
Hereby, HM Electronics, Inc. declares that the DX200 is in compliance with the essential requirements and other
relevant provisions of R&TTE Directive 1999/5/EC.
This product operates in the 2400 to 2483.5 MHz frequency range. The use of this frequency range is not yet
harmonized between all countries. Some countries may restrict the use of a portion of this band or impose other
restriction relating to power level or use. You should contact your Spectrum authority to determine possible restrictions.
MANDATORY SAFETY INSTRUCTIONS
FOR INSTALLERS AND USERS
Use only manufacturer or dealer supplied antennas.
The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio
Frequency) energy, which is below the OSHA (Occupational Safety and Health Act) limits.
The term “IC:” before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
Base Station Antenna minimum safe distance: 7.9 inches (20 cm) at 100% duty cycle.
Base Station Antenna gain: This device has been designed to operate with an antenna having a maximum
gain of up to 7dBi.
Antenna mounting: The antenna(s) used for the base transmitter must be installed to provide a separation
distance of at least 7.9 inches (20 cm) from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
Antenna substitution: Do not substitute any antenna for the one supplied by the manufacturer or radio dealer.
You may be exposing person or persons to excess radio frequency radiation. You may contact your radio
dealer or the manufacturer for further instructions.
WARNING: Maintain a separation distance from the base station transmit antenna to a person(s) of at least
7.9 inches (20 cm) at 100% duty cycle.
You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure
the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying
RF exposure compliance. The operation of this transmitter must satisfy the requirements of
Occupational/Controlled Exposure Environment, for work-related use. Transmit only when person(s) are at
least the minimum distance from the properly installed, externally mounted antenna.

Waste Electrical and Electronic Equipment (WEEE)
The European Union (EU) WEEE Directive (2002/96/EC) places an obligation on producers (manufacturers,
distributors and/or retailers) to take-back electronic products at the end of their useful life. The WEEE
Directive covers most HME products being sold into the EU as of August 13, 2005. Manufacturers, distributors
and retailers are obliged to finance the costs of recovery from municipal collection points, reuse, and recycling
of specified percentages per the WEEE requirements.
Instructions for Disposal of WEEE by Users in the European Union
The symbol shown below is on the product or on its packaging which indicates that this product was put on the
market after August 13, 2005 and must not be disposed of with other waste. Instead, it is the user’s
responsibility to dispose of the user’s waste equipment by handing it over to a designated collection point for
the recycling of WEEE. The separate collection and recycling of waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment for recycling, please
contact your local authority, your household waste disposal service or the seller from whom you purchased the
product.

LIMITED WARRANTY
HM Electronics, Inc. (“HME”) warrants the DX200 for a period of two (2) years*from the date of
purchase against defects in materials or workmanship provided it was purchased from an authorized
dealer. During the warranty period, defective HME Products will be repaired without charge for parts
and labor. Simply return the defective HME Product with your sales slip as proof of the date of
purchase. If a defective HME Product is returned prepaid to HME or an authorized HME service
center, it will be repaired and returned prepaid. Replacement of nonconforming goods and repair of
defective HME Products are the sole and exclusive remedies available under this warranty.
This warranty shall be void if (a) the HME Products have been tampered with, neglected, modified,
abused or misused; (b) anyone other than HME employees or authorized HME service
representatives provide service on or to the HME Products; or (c) the serial numbers are not intact.
THIS WARRANTY COVERS HME PRODUCTS, AND IS NOT EXTENDED TO ASSOCIATED NON-
HME PRODUCTS OR ACCESSORIES, OR ANY DAMAGE TO HME PRODUCTS CAUSED BY
SUCH NON-HME PRODUCTS OR ACCESSORIES. IN NO EVENT WILL HME BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LOSS OF PROFITS ARISING FROM THE
USE OF OR INABILITY TO USE ANY HME PRODUCTS, OR FROM ACCIDENTS OR ACTS OF
GOD.
HME MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO HME
PRODUCTS EXCEPT AS SPECIFICALLY SET FORTH ABOVE.
This warranty is provided to the original purchaser of the HME Products described on this packing list
and is non-transferable without the written permission of HME.
RETURN POLICY:
ALL SALES FINAL. No returns will be accepted (except for nonconforming goods as specified
above) unless HME authorizes such return and unless such return occurs within 90 days of receipt. A
15% restocking charge will be assessed on all such authorized returns. Authorized returns must be
freight prepaid and shall include an authorization number noted on the outside of the package. Such
authorization number will be provided by HME at the time it authorizes such return. All freight sent
collect and packages without an authorization number will be refused and returned to sender.
* Exceptions: The BAT40 Batteries and the HS14, HS20-3 Headsets are warranted for one
year. The HS4-3 Earpiece is warranted for 90 days.

1
The DX200 provides private, secure communication. Each base station can have up to a total of fifteen BP200
Beltpacs and/or WH200 All-in-one Wireless Headsets and/or WS200 Wireless Speaker Stations “registered” to
it. All Beltpacs or all WH200 Headsets, or a combination of Beltpacs, Headsets and Speaker Stations can be
used. Four of the fifteen can transmit at the same time. However, by connecting two or more base stations
together, these numbers can be increased. For example, two base stations can support thirty Beltpacs/
Headsets/Speaker Stations, of which eight can transmit at the same time. Beltpacs, Headsets or Speaker
Stations can be used either in the push-to-talk or hands-free mode. The base station operator can stop all
Beltpacs/Headsets/Speaker Stations from transmitting.
The DX200 can be used with RTS®and Clear-Com®cabled intercom systems. On the intercom channel, 2-wire
and 4-wire cabled intercoms can be operated at the same time. Also, using the AUX In and AUX Out
connections, a second 4-wire intercom channel can be used.
Either a monitor speaker or a local headset can be used with the DX200. Using a local headset, the base station
operator can talk to crew members on the cabled intercom channel, Beltpacs/Headsets/Speaker Stations only, or
all channels.
The BS200 Base Station and WS200 Speaker Station can be operated using standard DC electricity or a vehicle
electrical system for mobile operation. A power supply and cable are included with the base station.
SECTION 1. INTRODUCTION

2
AC40A
Battery Charger
WS200
Wireless Speaker Station
EQUIPMENT IDENTIFICATION
The following equipment is standard with the DX200 Wireless Intercom System.
As you unpack the equipment, check the enclosed shipping document to be sure you received all items listed.
Base Station Antennas
(2 per Base Station)
115/230 Volt AC Power Supply
(1 per Base Station, with Power Cord)
(1 per AC40A Battery Charger, with Power Cord)
BS200 Base Station
OPTIONAL EQUIPMENT
HS4-3 Earpiece & Lapel Microphone
HS14 Single-Muff Medium-Weight Headset
HS14D Dual-Muff Medium-Weight Headset
HS20-3 Dual-Muff Lightweight Headset
HSI6000 Headset Interface
XLR Headset Adapters:
MD-XLR4M Mini-DIN to 4-Pin Male
MD-XLR4F Mini-DIN to 4-Pin Female
MD-XLR5F Mini-DIN to 5-Pin Female
BAT850 Rechargeable Battery
AC850 Battery Charger
WS200 Battery Sled
115/230 Volt AC Power Supply
with Power Cord for WS200
Battery
WH200 All-in-one
Wireless Headset HS14 Headset Beltpac Pouch
BP200 Beltpac

3
56
MAIN EQUIPMENT FEATURES
Beltpac Features
1. Headset cable connector
2. Beltpac power lights
3. ISO (Isolate) button
4. IC (Intercom) button
5. PWR (Power) button
6. Volume-up Sbutton
7. Volume-down Tbutton
8. Battery
9. Battery release latch
WH200 Headset Features
1. Power light
2. Transmit light
3. IC1 & IC2 (Intercom) buttons
4. ISO (Isolate) button
5. Volume-up Sbutton
6. Volume-down Tbutton
7. Power button
8. Battery release latch
9. Battery
2 3 4 2
1
5
6
7
8 9
2
1
4
3
3
5
6
7 8
9

4
Speaker Station Features
1. SIDE TONE adjustment (recessed)
2. Battery compartment cover
3. Battery compartment cover release latches
4. HEADSET connector
5. POWER button and light
6. CALL light and MIC (microphone)
7. SPEAKER and light
8. ISO (Isolate) button and light
9. VOLUME down Tand up Sbuttons
10. IC (Intercom) button and light
11. 12-14VDC power adapter cable connector
12. External speaker connector
4
1 5 6 7 8 109 1211
2
3
Left side
p
anel Front
p
anel Ri
g
ht side
p
anel

5
24 25 26 27 28 29 30 31 32 33 34 35 36 37
Base Station Features
Front Panel
1. POWER switch
2. RESET REGISTRATION button
3. REGISTRATION STATUS display
4. UNLATCH button
5. IC (Intercom) receiver level control and
indicator light
6. ISO (Isolate) receiver level control and
indicator light
7. 2W and 4W indicator lights
8. SND and RCV (Send and Receive) controls
9. AUX IN and OUT (Auxiliary In and Out)
controls
10. LOCAL HEADSET VOLUME control
11. LOCAL HEADSET ISO indicator light
12. LOCAL HEADSET IC indicator light
13. LOCAL HEADSET MIC LEVEL control
14. LOCAL HEADSET TALK indicator light
15. LOCAL HEADSET cable connector
16. RESET button (recessed)
17. REGISTER BELTPAC button
18. 2W/4W button
19. 4W ONLY button
20. AUX IN button
21. ISO+ button
22. LOCAL HEADSET IC/ISO SELECT button
23. LOCAL HEADSET TALK button
Rear Panel
24. CLEAR-COM / RTS TW button
25. CH1/CH2 RTS channel select button
26. TERM OFF/TERM ON local termination
select button
27. 2-WIRE intercom connector (female)
28. NULL control
29. 2-WIRE intercom connector (male)
30. 4-WIRE connector
31. 0oANTENNA connector
32. 90oANTENNA connector
33. AUX IN connector
34. AUX OUT connector
35. 8-OHM SPKR 2-pin Phoenix connector
36. 12-14VDC Power connector
37. Chassis ground connector
16 17 18 19 20 21 22 23
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

6
BATTERY CHARGER SETUP
IMPORTANT! – Before installing the system, connect the AC power supply to the AC40A Battery Charger
and plug it into an electrical outlet. Charge all the batteries for the Beltpacs and/or WH200 Headsets while the
other equipment is being installed. Charging time is about 2.5 hours.
Connect AC Power Supply
•Attach the AC power supply cable connector to the screw connector on the battery charger.
•Plug the power cord connector into the AC power supply.
•Plug the power cord into an electrical outlet.
The red lights on the charger will come on and go off, and then the yellow lights will come on and stay on.
Charge Batteries
Up to four batteries can be charged in the battery
charger at the same time. The battery status lights
next to each charging port are explained below.
Up to six fully charged batteries can be stored in the
battery storage ports.
•Insert a battery in each of four charging ports
until it clicks in place.
•A yellow light next to each charging port stays on
while the port is empty. When a battery is in a
charging port, a flashing yellow light next to it
indicates CHARGE PENDING, which means the
battery is too hot. Adjust the room temperature or
move the charger to a cooler area. When a battery is
in a charging port, a yellow light on steady next to it
means CHARGE FAILED. If this happens, follow
the instructions on the side of battery charger.
•A red CHARGING light next to a battery port
stays on while a battery in the port is charging.
A green READY light next to a battery port goes
on when a battery in the port is fully charged.
Store fully charged batteries in storage ports.
Batteries should not be left in charge ports after being
fully charged. If a battery is left in a charge port for
more than three weeks, the yellow indicator may light
up. In this case, it does not indicate a faulty battery.
SECTION 2. EQUIPMENT SETUP
Power cord
connecto
r
Charged batteries
in storage ports
Battery in
charging port
Empty
charging ports
AC
p
ower su
pp
l
y
Power cord
Power supply
cable connecto
r
AC40A Batter
y
Char
g
e
r
To electrical
outle
t

7
BASE STATION SETUP
The following description is for a basic, stand-alone DX200 system setup.
Connections and setup for multiple, daisy-chained base stations are described on pages 8 – 10.
Connections with 2-wire and 4-wire intercoms, and other auxiliary equipment are described in the INTERCOM
AND AUXILIARY EQUIPMENT SETUPS on pages 20 and 21.
Equipment Connections
Rear Panel
Front Panel
Step 1. Connect the two enclosed antennas to the antenna connectors (#31 and #32) on the rear panel of the base
station. Position the antenna at the 0° ANTENNA connector (#31) vertically. Position the antenna at the
90° ANTENNA connector (#32) horizontally, pointing to the left as indicated on the panel. Turn the sleeve
on each of the antenna connectors clockwise to tighten them securely in place.
Step 2. Plug the connector at the end of the AC power supply cord into the 12-14VDC power connector (#36) on
the rear panel of the base station. Turn the nut on the cable connector clockwise to secure it to the base
station. Plug the large female connector at one end of the AC power cord into the power supply. Plug the
other end of the AC power cord into an electrical outlet.
Step 3. Connect a grounding wire from #37 to an earth ground.
Step 4. Plug a headset into the HEADSET connector (#15) on the front panel of the base station.
Step 5. Press the POWER switch (#1) to turn on the base station. The red light on the switch should go on.
31 32 36 37
1 3 17 15

8
27 29
Multiple Base Stations
Two or more base stations can be “daisy-chained” together with cables connected to the 2-wire connectors
(#27 and #29) on the rear panel of each base station, following Clear-Com®/RTS®standards.
NOTE: The base station does not provide or require 2-wire line power.
The cable connectors must
be 3-pin XLR type with the
following pin connections: RTS®Mode Clear-Com®Mode
Pin 1 = Common Pin 1 = Common
Pin 2 = Channel 1 Pin 2 = N/C
Pin 3 = Channel 2 Pin 3 = Audio
If “daisy-chaining” multiple base stations, you must do the following:
Step 1. Press TERM push button in (TERM ON) to terminate.
Be sure you do this in only one base station.
Step 2. For each base station, follow all the steps in
the BASE STATION SETUP section on page 7.
Step 3. Follow the procedure below to initialize each base station.
Base Station Initialization
For the base stations to be co-located near each other and operate without self-interference they must all be
properly initialized before performing any other setups. After initializing each base station, register each
Beltpacs/Headsets/Speaker Station to that base according to the procedures on pages 11 - 18.
One base station must be designated as “primary” while the others are designated as “secondary”. You may
have only one primary and up to 3 secondary base stations. Secondary base stations are assigned numbers 1, 2,
or 3 during initialization, to differentiate them in frequency offset.
•Label the base stations as “Primary,” “1,” “2” and “3.”
•Start with every base station and Beltpac/Headset/Speaker Station power off.
Configure each secondary base station as follows:
•First, remove the six screws from the top and three screws from each side of the top cover, and lift the
cover off and set it aside.
•Locate the DIP switch on the transceiver circuit board inside the base station. Set DIP switch #4 to the ON
position. Leave #s 1, 2 and 3 in the OFF position.
•Replace the cover and screws on the base station.
DIP switch inside
secondary
base station

9
Initialize each base station and register all Beltpacs/Headsets/Speaker Stations as follows:
•Turn the primary base station power on. Register any Beltpacs/Headsets/Speaker Stations to be used with
the primary base station (See pages 11 - 18). Turn each Beltpac/Headset/Speaker Station off after
registering it.
•Power on one secondary base station. The REGISTRATION STATUS display will show a double bar,
indicating the secondary base is ready to be initialized.
Base station ready to be initialized Small "o" indicates primary base
is open for registration
•Press the REGISTER BELTPAC button on the primary base. The REGISTRATION STATUS display
will show a small “o.”
•To assign a number to a secondary base station and initialize it, press the REGISTER BELTPAC button
on the secondary base. Pressing the button repeatedly causes it to cycle through the numbers 1, 2, and 3.
When the desired number appears, stop pressing and wait. While the secondary base initializes using the
displayed number, the REGISTRATION STATUS display will continue showing the secondary number
selected. When initialization of the secondary base station is finished, the display will show one bar, to
indicate the secondary has initialized to the primary.
Secondary 2 searching for primary Secondary is initialized to primary
•Press the REGISTER BELTPAC button on the primary. The REGISTRATION STATUS display will
go blank.
•Register Beltpacs/Headsets/Speaker Stations to the secondary (See pages 11 - 18). After registration, turn
off the secondary base and all Beltpacs/Headsets/Speaker Stations.
Double bar Small “o”
Secondary
base number One bar

10
•Repeat these steps for each remaining secondary base. Use a different number for each. Only the primary
base and the secondary base you are working with should have power on during initialization. All other
equipment should be off.
•After all secondary bases are initialized and Beltpacs/Headsets/Speaker Stations are registered power up all
bases. Press reset on the primary base and let it recover. Turn on the primary Beltpacs/Headsets/Speaker
Stations and let them link. Press the reset on each secondary base one at a time and let it initialize to the
primary, as indicated by a single bar. Turn on the Beltpacs/Headsets/Speaker Stations associated with the
secondary bases. Do one group at a time until they have all linked. Then do the next group. At this point
all bases and Beltpacs/Headsets/Speaker Stations should be powered up and linked, ready for use.
•Now proceed with normal system configuration, setting functions and levels as required.
•If it becomes necessary to replace an secondary base, use the procedure above to initialize the new
secondary with the same number as the old secondary. After initialization you will have to register any
Beltpacs/Headsets associated with the old secondary to the new secondary.
•If it becomes necessary to replace a primary base, follow the above procedure completely. Before
initialization of the secondary bases, clear the previous secondary initialization as follows. For each
secondary, press the RESET REGISTRATION button and the RESET button at the same time. Continue
holding the RESET REGISTRATION button after you release the RESET button, until the clear code “c”
(lower case) appears on the REGISTRATION STATUS display. Any Beltpacs/Headsets/Speaker Stations
associated with the old primary will have to be registered to the new primary after secondary base
initialization. All Beltpacs/Headsets/Speaker Stations associated with secondary base stations also have to be
registered again.
•If the primary base is shut down or if the primary base is powered on for more than 30 seconds after the
secondary bases, all secondary bases will drop their Beltpac/Headset/Speaker Station connections and
begin searching for the primary. If the primary is not found in 30 seconds, the secondary will automatically
revert to primary-mode operation and reconnect the Beltpacs/Headsets/Speaker Stations. At this point the
secondary REGISTRATION STATUS displays will show three bars. If the primary is turned back on it
will be necessary to press RESET on all secondary bases to allow them to find and initialize to the primary
again. It is therefore important to have all bases connected to the same AC circuit to prevent this situation
when the system is shut down after hours and powered up again the next day.
Secondary base operating in primary mode when no primary base is found
NOTE: You cannot register Beltpacs/Headsets/Speaker Stations to a base that is set to primary mode, and
then switch the base mode to secondary for initialization. Once in secondary mode, the base cannot
recognize the Beltpacs/Headsets/Speaker Stations registered during primary operation. For
secondary bases, the Beltpacs/Headsets/Speaker Stations must always be registered after secondary
base initialization, with the primary base remaining active and the secondary base displaying one bar.
Three bars

11
BELTPAC / WH200 HEADSET / SPEAKER STATION
SETUP AND REGISTRATION
The first time you operate the DX200 system, you must register each Beltpac, WH200 Headset and/or WS200
Speaker Station for use with a specific base station. The base station will then recognize all registered
Beltpacs/Headsets/Speaker Stations when their power is on, and will know the difference between them and
other electronic equipment operating on the same frequencies. If a Beltpac/Headset/Speaker Station is added or
replaced later, the new one must be registered and the old one remains in memory. A maximum of 15 Beltpacs
and/or Headsets and/or Speaker Stations can be registered to a single base station at one time. If the maximum
number of 15 is exceeded, you must clear all current registrations and re-register all active Beltpacs/Headsets/
Speaker Stations.
NOTE: The following two pages are for Beltpac setup and registration. WH200 Headset setup and
registration instructions are on pages 13 and 14. Instructions for WS200 Speaker Station setup and
registration are on pages 15 - 18.
Set Up Beltpacs
Before registering them, set up all Beltpacs as follows.
Step 1. Insert a fully charged battery in the
Beltpac, with the metal contacts on
the end of the battery inserted first.
Press it in until it snaps.
Step 2. Place the Beltpac in the pouch.
Step 3. Plug the headset cable connector into the Beltpac.
Register Beltpacs
Beltpacs must be within 6 feet (1.83 meters) of the base station while you are registering them. Be certain the
base station power is on, and each Beltpac you are going to register is turned off before you begin. Beltpacs that
are already registered can be on or off.
NOTE: If you are setting up multiple, daisy-chained base stations, the following steps must be repeated for
Beltpacs being registered to each base station.
Step 1. Put the headset, of the Beltpac being registered, on your head.
Step 2. Press the REGISTER BELTPAC button on the front panel of
the base station (#17 on base station front panel illustration).
•The REGISTRATION STATUS display (#3on base
station front panel illustration) will show a small “o”
for open.
NOTE: If you wait too long before going on to Step 3,
the base station will go out of the registration
mode and you will have to repeat Step 2.
Step 3. Press and hold the ISO button on the Beltpac while you press and
release the PWR (power) button to turn the unit on, then release the
ISO button. This will cause the Beltpac to enter the registration mode.
•The two power lights at the corners of the Beltpac near the IC
and ISO buttons will begin blinking red, then will blink green
two or three times and go off.
•Wait! There may be a short delay.
Ste
p
1
Ste
p
2 Ste
p
3
17
3

12
If registration is successfully completed:
•A voice message in the headset will say “Power on, Beltpac #, Version #, Begin registration, Registration
complete, …”
•After a delay of up to 15 seconds, the REGISTRATION STATUS display will show the ID number assigned
to this Beltpac for about 10 seconds.
NOTE: ID numbers are assigned sequentially as 0 thru 9, A, b, C, d and E.
•The power light on the Beltpac, next to the IC button, will remain on steady green.
•Repeat Steps 1 to 3 on page 11 for each Beltpac to be registered.
If registration failed:
•A voice message in the headset will say “Power on, Beltpac #, Version #, Begin registration, …” Both
power lights on the Beltpac will be blinking red, and there may be a delay of up to 90 seconds before you
hear “Registration failed.”
•Press RESET (#16) on the base station. To press RESET, insert a small paper clip or similar object into
the RESET hole at the lower-left corner of the base station front panel. When the REGISTRATION
STATUS display (#3) becomes blank, press the REGISTER BELTPAC button (#17) and register the
Beltpac again. If registration fails again, call your dealer for assistance.
If you try to register more than 15 Beltpacs and/or WH200 Headsets and/or Speaker
Stations to a base station:
•An Fwill appear on the REGISTRATION STATUS display (#3) on the base station and you will hear
“Registration failed” in the Headset.
•Clear all current registrations by pressing the RESET REGISTRATION button (#2) and RESET (#16) at the
same time. To press RESET, insert a small paper clip or similar object into the RESET hole at the lower-
left corner of the base station front panel. Continue holding the RESET REGISTRATION button after you
release RESET, until the clear code “c” (lower case) appears on the REGISTRATION STATUS display.
•Register all active Beltpacs, one at a time.
Previously registered WH200 Headsets and Speaker Stations must also be re-registered.
16 17
2 3

13
Set Up WH200 Headsets
Before registering them, insert a fully charged battery in each Headset,
with the metal contacts on the end of the battery inserted first. Press it
in until it snaps.
Power On/Off
•To turn power on
Press and release the power button on the inside of the Headset housing. A voice message in the earpiece
will say “Headset #” and the power light on the opposite side of the earpiece will go on.
•To turn power off
Press and hold the power button for approximately 3 seconds. A voice message in the earpiece will say
“Headset off,” and the power light on the opposite side of the earpiece will go off.
Register WH200 Headsets
Headsets must be within 6 feet (1.83 meters) of the base station while you are registering them. Be certain the
base station power is on, and each Headset you are going to register is turned off before you begin. Headsets
that are already registered can be on or off.
NOTE: If you are setting up multiple, daisy-chained base stations, the following steps must be repeated for
Headsets being registered to each base station.
Step 1. Put the Headset on your head.
Step 2. Press the REGISTER BELTPAC button on the front panel of the base station (#17 on base station front
panel illustration).
•The REGISTRATION STATUS display (#3on
base station front panel illustration) will show a
small “o” for open.
NOTE: If you wait too long before going on to
Step 3, the base station will go out of the
registration mode and you will have to
repeat Step 2.
Step 3. Press and hold the ISO button on the Headset while you
press and release the power button to turn the unit on, then
release the ISO button. This will cause the Headset to enter
the registration mode.
•The Headset power light will begin blinking red, then will blink green two or three times and go off.
Wait! There may be a short delay.
Power
b
utton Power
li
g
h
t
17
3

14
If the registration is successfully completed:
•A voice message in the Headset will say “Power on, Headset #, Version #, Begin registration, Registration
complete, …”
•After a delay of up to 15 seconds, the REGISTRATION STATUS display will show the ID number assigned
to this Headset for about 10 seconds.
NOTE:ID numbers are assigned sequentially as 0 thru 9, A, b, C, d and E.
•The power light on the Headset will remain on steady green.
•Repeat Steps 1 to 3 above for each Headset to be registered.
If registration failed:
•A voice message in the Headset will say “Power on, Headset #, Version #, Begin registration, …” The
power light on the Headset will be blinking red, and there may be a delay of up to 90 seconds before you
hear “Registration failed” and an Fwill appear on the REGISTRATION STATUS display (#3).
•Press RESET (#16) on the base station. To press RESET, insert a small paper clip or similar object into
the RESET hole at the lower-left corner of the base station front panel. When the REGISTRATION
STATUS display (#3) becomes blank, press the REGISTER BELTPAC button (#17) and register the
Headset again. If registration fails again, call your dealer for assistance.
If you try to register more than 15 WH200 Headsets and/or Beltpacs and/or Speaker
Stations to a base station:
•An Fwill appear on the REGISTRATION STATUS display (#3) on the base station and you will hear
“Registration failed” in the Headset.
•Clear all current registrations by pressing the RESET REGISTRATION button (#2) and RESET (#16) at
the same time. To press RESET, insert a small paper clip or similar object into the RESET hole at the
lower-left corner of the base station front panel. Continue holding the RESET REGISTRATION button
after you release RESET, until the clear code “c” (lower case) appears on the REGISTRATION STATUS
display.
•Register all active WH200 Headsets, one at a time.
Previously registered Beltpacs and Speaker Stations must also be re-registered.
16 17
2 3

15
Set Up Speaker Stations
The WS200 Speaker Station can be used together with Beltpacs and WH200 All-in-one Headsets. It provides
wireless communication through its built-in microphone and speaker, or a plug-in headset. A remote speaker can
also be connected to the unit.
The Speaker Station can be used on a table top or mounted on the wall. It can be operated with standard AC
power, 12-14VDC or with six AA batteries or an optional rechargeable battery. A power supply with cord and a
battery sled are provided. Whether used on a table top or mounted on the wall, if AC operation is required, the
Speaker Station must be located close enough to an electrical outlet to be reached with the power supply and cord.
Wall Mounting
•Hold the unit against the wall where you will mount it
and mark the wall through the four holes in the flanges
on its left and right sides.
•Drill holes in the wall at the four marked spots, and
mount the WS200 over the holes with your
selected hardware (not provided).
AC Power Operation
If using the WS200 with AC power ―
•Plug the connector at the end of the power supply cable into the 12-14 VDC power connector on right
side of the unit. Turn the sleeve on the connector clockwise to secure it to the unit.
•Plug the large female connector at one end of the AC power cord into the power supply. Plug the other
end of the AC power cord into an electrical outlet.
1 2
3 4
Power supply cable AC power cord
Power supply
Having a fully charged (or new) battery in its battery compartment when operating the WS200 with AC or
external DC power can prevent interruption of communication during a power outage. The WS200 will
automatically switch to battery power.