HMS Networks Airconwithme Application guide

Device Configuration
Issue date: 03/2021
V1.0

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
2 / 20
Important User Information
Disclaimer
The information in this document is for informational purposes only. Please inform HMS
Industrial Networks of any inaccuracies or omissions found in this document.
HMS Industrial Networks disclaims any responsibility or liability for any errors that may appear
in this document. HMS Industrial Networks reserves the right to modify its products in line
with its policy of continuous product development. The information in this document shall
therefore not be construed as a commitment on the part of HMS Industrial Networks and is
subject to change without notice. HMS Industrial Networks makes no commitment to update
or keep current the information in this document.
The data, examples and illustrations found in this document are included for illustrative
purposes and are only intended to help improve understanding of the functionality and
handling of the product. In view of the wide range of possible applications of the product, and
because of the many variables and requirements associated with any particular
implementation, HMS Industrial Networks cannot assume responsibility or liability for actual
use based on the data, examples or illustrations included in this document nor for any
damages incurred during installation of the product. Those responsible for the use of the
product must acquire sufficient knowledge in order to ensure that the product is used correctly
in their specific application and that the application meets all performance and safety
requirements including any applicable laws, regulations, codes and standards. Further, HMS
Industrial Networks will under no circumstances assume liability or responsibility for any
problems that may arise as a result from the use of undocumented features or functional side
effects found outside the documented scope of the product. The effects caused by any direct
or indirect use of such aspects of the product are undefined and may include e.g. compatibility
issues and stability issues.

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
3 / 20
INDEX
1. Description................................................................................................................................................4
1.1 Introduction .......................................................................................................................................4
1.2 About this document.........................................................................................................................4
1.3 What is needed.................................................................................................................................4
2. Airconwithme Button.................................................................................................................................6
2.1 Reset Wi-Fi settings..........................................................................................................................6
2.2 WPS mode........................................................................................................................................7
2.3 Change Wi-Fi channel ......................................................................................................................8
3. Configuration ............................................................................................................................................9
3.3 Automatic....................................................................................................................................... 12
3.4 Manual ........................................................................................................................................... 14
3.5 WPS............................................................................................................................................... 16
3.6 Settings.......................................................................................................................................... 18
4. LED status information .......................................................................................................................... 20
4.1 LED status during Wi-Fi configuration ........................................................................................... 20
4.2 LED status during working mode................................................................................................... 20

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
4 / 20
1. Description
1.1 Introduction
Airconwithme is the perfect IoT solution for AC management. It has been developed under
Mitsubishi Heavy specifications and offers the possibility to control the domestic AC unit from
an app available for Android and iOS.
The Airconwithme system offersfunctionalities like energy saving making the product the best
professional solution for offices, stores, schools, or any other commercial building.
Figure 1.1 Airconwithme integration.
1.2 About this document
This document describes how to configure the Airconwithme device It contains the meaning
of the feedback light from Airconwithme LED during the configuration process and working
mode
1.3 What is needed
To use Airconwithme system is needed, at least, the following:
•Airconwithme device.
Before start using Airconwithme is needed to acquire (if the user hasn’t done yet) an
Airconwithme device
1
. In addition, is necessary be close to it (See Figure 1.2)
1
Airconwithme devices can be purchased in your usual air conditioner or heat pump reseller center.

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
5 / 20
Figure 1.2 Get close to the device.
•Make sure Airconwithme device is compatible with the Indoor unit.
Check the compatibility.
•Internet access
2
.
The Airconwithme device must be connected to internet using Wi-Fi, therefore make
sure the Wi-Fi signal reaches the device location (See Figure 1.3).
Figure 1.3 Check Wi-Fi Signal.
•Device with Internet access:
A device with internet access is needed (Smartphone or Tablet).
Make sure the smartphone or tablet used is Android or iOS compatible.
In addition, double check that the data is turned off and Wi-Fi is turned on.
2
Costs related with Internet access are not included in the Airconwithme price. Ask your Internet Service Provider about the associated
costs of your Internet connection.
<2m
OK

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
6 / 20
2. Airconwithme Button
Airconwithme devices have one unique button (See Figure 2.1).
Figure 2.1 Airconwithme´ s button
2.1 Reset Wi-Fi settings
To reset the Wi-Fi information in an Airconwithme device is needed to hold the button for 10
seconds (See Figure 2.2), the light of the LED will blink in green after some seconds it will
turn steady green (See Figure 2.3).
Figure 2.2 Reset Wi-Fi procedure.
Figure 2.3 Reset LED feedback.
Green
Blinking
Green
Steady
<10 sec
10 sec

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
7 / 20
2.2 WPS mode
Press one time the button to activate the WPS mode in the Airconwithme device (See Figure
2.4), the light of the LED will blink in blue (See Figure 2.5).
Figure 2.4 WPS mode.
Figure 2.5 WPS mode LED feedback.
“Click”
Blue
Blinking

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
8 / 20
2.3 Change Wi-Fi channel
Holding the button for 2 seconds to change the channel of the Wi-Fi network (See Figure 2.6),
the light of the LED will blink in green and it will turn steady green (See Figure 2.7). The
process can be repeated until reach the channel wanted.
Figure 2.6 Change Wi-Fi channel procedure.
Figure 2.7 Change Wi-Fi channel LED feedback.
2 sec
<2 sec
Green
Blinking
Green
Steady

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
9 / 20
3. Configuration
There are 2 ways to realize the procedure
1. Tap on the white square in the main page (See Figure 3.1).
2. Login, tapping on settings and on the white square (See Figure 3.2).
Figure 3.1 Access to Configuration network device without login.
Figure 3.2 Access to Configuration network device from settings login.
Go to Wi-Fi settings of your mobile or Table and select the network generated by
Airconwithme device (See Figure 3.3). Tap on Next.
Note: Make sure to reset the Wi-Fi configuration. Further
information can be found in Section 2.1.
!

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
10 / 20
In case the user is not connected to the device network a pop-up window will be shown asking
to connect to it. (See Figure 3.4).
The mode to configure the Wi-Fi network can be selected as preference. Further information
about each mode configurations will be found at Section 3.3, Section 3.4 and Section 3.5.
Figure 3.3 Configuration network procedure.
Figure 3.4 Configuration network warning pop-up window.
If the configuration network has been carried out successfully the light of the LED will follow
a light sequence (See Figure 3.5). Tap on Done.

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
11 / 20
Figure 3.5 LED configuration network sequence.

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
12 / 20
3.3 Automatic
1. Tap on Automatic (See Figure 3.6)
Figure 3.6 Automatic configuration procedure.
2. Tap on name of the network wanted (See Figure 3.7)
Figure 3.7 Wi-Fi Network selection.
3. Enter the password of the Wi-Fi network selected, to double check if the password
entered is the correct one and tap on show password (See Figure 3.8). Tap on
Connect.

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
13 / 20
Figure 3.8 Enter password.
If the configuration network has been carried out successfully the light of the LED will follow
a light sequence (See Figure 3.5). To continue tap on done.
In case the light of the LED does not follow the sequence or start lighting different, start the
process from the beginning.

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
14 / 20
3.4 Manual
Tap on Manual (See Figure 3.9)
Figure 3.9 Manual configuration procedure.
•In case to select the security open, type the SSID of the Wi-Fi network wanted. (See
Figure 3.10). Tap on Connect.
Figure 3.10 Security Open.
If the configuration network has been carried out successfully the light of the LED will follow
a light sequence (See Figure 3.5). Tap on Done.
In case the light of the LED does not follow the sequence or start lighting different, start the
process from the beginning.
•In case to select the security WEP/WAP2 type the SSID of the Wi-Fi network wanted.
Also, type the password Wi-Fi network and to make sure is well entered slide Show
password selector (See Figure 3.11). Tap on Connect.

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
15 / 20
Figure 3.11 Security WEP/ WPA2.
If the configuration network has been carried out successfully the light of the LED will follow
a light sequence (See Figure 3.5). Tap on Done.
In case the light of the LED does not follow the sequence or start lighting different, start the
process from the beginning.
In manual mode is an option for advanced configuration. (See Figure 3.10 and Figure 3.11).
By default, it comes in option DHCP (See Figure 3.12). Tap on Save.
Figure 3.12 Advanced options (DHCP).
•In case to select Static IP, type the IP address, Subnet Mask and Getaway. (See Figure
3.13). Tap on Save.
Figure 3.13 Advanced options (Static IP).

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
16 / 20
3.5 WPS
There are 2 ways to start the WPS configuration procedure
1. Tap on WPS (See Figure 3.14).
2. Press one time the button to activate the WPS. Further information can be found at
Section 2.2
Figure 3.14 WPS configuration procedure.
Follow the instructions in the screen shown (See Figure 3.15). Tap on Next.
Figure 3.15 Instructions to perform WPS mode configuration.
the light of the LED will blink blue, 2 minutes after the WPS button of the router had been
pressed the light of the LED will be off (See Figure 3.16).

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
17 / 20
Figure 3.16 Performing WPS configuration LED feedback.
If the configuration network has been carried out successfully the light of the LED will follow
a light sequence (See Figure 3.5). To continue tap on Done.
In case the light of the LED blinks Magenta (See Figure 3.17), start the process from the
beginning.
Figure 3.17 Unsuccessful connection LED feedback.
Blue
Blinking
OFF
“Click”
<2 min
<2 min
Magenta
Blinking

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
18 / 20
3.6 Settings
In settings the domain region where the Airconwithme device will work can be changed,
also, if the installation has more than device and the user needs to identify which device is
going to be configured it can be called.
Tap on Settings (See Figure 3.18)
Figure 3.18 Settings configuration site.
•To identify to which network Airconwithme device is connected the mobile or tablet tap
on Identify (See Figure 3.19). the light of the LED will blink white for 6 seconds, then it
will be off (See Figure 3.20).
Figure 3.19 Settings Airconwithme.

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
19 / 20
Figure 3.20 Identify LED feedback.
•To change of Region, tap on the region wanted (See Figure 3.19). A pop-up will be
shown telling that if the region is changed the configuration process must be started
from the beginning (See Figure 3.21). Tap on OK.
Tap on Save (See Figure 3.19).
The light of the LED will blink green for 6 seconds, then it will turn steady green (See
Figure 3.22)
Figure 3.21 Change region.
Figure 3.22 Selecting region LED feedback.
White
Blinking
OFF
6 sec
Green
Blinking
Green
Steady
<6 sec

Device Configuration 1.0
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
URL https://airconwithme.com
20 / 20
4. LED status information
Airconwithme device has an external LED which uses to give the user a feedback to
communicate the status of the device.
4.1 LED status during Wi-Fi configuration
LED Color (s)
Behavior
Description
Blue
Blinking
Performing WPS connection (up to 2 min)
Magenta
Blink
WPS connection error
White
Blinking
Identifying Airconwithme Device
Green
Steady
Not configured
Green
Blinking
Checking device configuration parameter values (up to 2 min)
Red
Blinking
Connecting to access point and server (up to 2 min)
Yellow
Blinking
Downloading configuration. Wait (up to 2 min)
Red - Green
Alternate blinking
Error Connecting to Access point or router. Try to connect
again and make sure you write the correct password.
Yellow - Green
Alternate blinking
Server not reached. Check if there is Internet connectivity on
your Access Point or router.
4.2 LED status during working mode
LED Color
Behavior
Description
Off
Airconwithme device not powered or Airconwithme device
working, and the AC unit is Off.
Blue
Steady
Indoor Unit ON working in Cool or Dry mode
Red
Indoor Unit ON working in Heat mode
Green
Indoor Unit ON working in Fan mode
Yellow
Indoor Unit ON working in Auto mode
Cyan
Indoor Unit working in anti-frost mode
Blue
3 blinks
Command received or sent during Cool or Dry mode
Red
Command received or sent during Heat mode
Green
Command received or sent during Fan mode
Yellow
Command received or sent during Auto mode
Cyan
Command sent during anti-frost mode
Red
Blinking
Airconwithme device trying to connect to the Internet