HMS Networks Anybus Wireless Bolt LTE User guide

Anybus®Wireless Bolt LTE™
STARTUP GUIDE
SP2868
Version 1.2
Publicaon date 2022-05-16
ENGLISH

Important User Informaon
Disclaimer
The informaon in this document is for informaonal purposes only. Please inform
HMS Networks of any inaccuracies or omissions found in this document. HMS Networks
disclaims any responsibility or liability for any errors that may appear in this document.
HMS Networks reserves the right to modify its products in line with its policy of
connuous product development. The informaon in this document shall therefore not
be construed as a commitment on the part of HMS Networks and is subject to change
without noce. HMS Networks makes no commitment to update or keep current the
informaon in this document.
The data, examples and illustraons found in this document are included for illustrave
purposes and are only intended to help improve understanding of the funconality and
handling of the product. In view of the wide range of possible applicaons of the product,
and because of the many variables and requirements associated with any parcular
implementaon, HMS Networks cannot assume responsibility or liability for actual use
based on the data, examples or illustraons included in this document nor for any
damages incurred during installaon of the product. Those responsible for the use of
the product must acquire sucient knowledge in order to ensure that the product is
used correctly in their specic applicaon and that the applicaon meets all performance
and safety requirements including any applicable laws, regulaons, codes and standards.
Further, HMS Networks will under no circumstances assume liability or responsibility for
any problems that may arise as a result from the use of undocumented features or
funconal side eects found outside the documented scope of the product. The eects
caused by any direct or indirect use of such aspects of the product are undened and may
include e.g. compability issues and stability issues.
Copyright © 2022 HMS Networks
Contact Informaon
Postal address:
Box 4126
300 04 Halmstad, Sweden
E-Mail: inf[email protected]

1. Preface
1.1. About This Document
This document describes how to install Anybus® Wireless Bolt LTE™.
For addional documentaon and soware downloads, FAQs, troubleshoong guides and
technical support, please visit www.anybus.com/support.
1.2. Document Convenons
Safety Symbols
DANGER
Instrucons that must be followed to avoid an imminently hazardous
situaon which, if not avoided, will result in death or serious injury.
WARNING
Instrucons that must be followed to avoid a potenal hazardous situaon
that, if not avoided, could result in death or serious injury.
CAUTION
Instrucon that must be followed to avoid a potenal hazardous situaon
that, if not avoided, could result in minor or moderate injury.
IMPORTANT
Instrucon that must be followed to avoid a risk of reduced funconality
and/or damage to the equipment, or to avoid a network security risk.
Preface Anybus® Wireless Bolt LTE™
SP2868 Version 1.2 Page 1 of 28

Informaon Symbols
NOTE
Addional informaon which may facilitate installaon and/or operaon.
TIP
Helpful advice and suggesons.
1.3. Trademarks
Anybus® is a registered trademark and Wireless Bolt LTE™ is a trademark of HMS Networks
AB.
All other trademarks are the property of their respecve holders.
Anybus® Wireless Bolt LTE™Trademarks
Page 2 of 28 SP2868 Version 1.2

2. Safety
2.1. General Safety
CAUTION
This equipment emits RF energy in the ISM (Industrial, Scienc, Medical)
band. Make sure that all medical devices used in proximity to this
equipment meet appropriate suscepbility specicaons for this type of
RF energy.
CAUTION
This equipment contains parts that can be damaged by electrostac
discharge (ESD). Use ESD prevenon measures to avoid damage.
CAUTION
Minimum temperature rang of the cable to be connected to the eld
wiring terminals, 90 °C.
CAUTION
Use copper wire only for eld wiring terminals.
CAUTION
This equipment is recommended for use in both industrial and domesc
environments. For industrial environments it is mandatory to use the
funconal earth connecon to comply with immunity requirements. For
domesc environments the funconal earth must be used if a shielded
Ethernet cable is used, in order to meet emission requirements.
Safety Anybus® Wireless Bolt LTE™
SP2868 Version 1.2 Page 3 of 28

2.2. Intended Use
The intended use of this equipment is as a communicaon interface and router.
The equipment receives and transmits data over Ethernet and Cellular standard networks.
Anybus® Wireless Bolt LTE™Intended Use
Page 4 of 28 SP2868 Version 1.2

3. Preparaon
3.1. Support and Resources
For addional documentaon and soware downloads, FAQs, troubleshoong guides and
technical support, please visit www.anybus.com/support.
TIP
Have the product arcle number available, to search for the product
specic support web page. You nd the product arcle number on the
product cover.
3.2. Network Environment
Ensure that you have all the necessary informaon about the capabilies and restricons
of your local network environment before installaon.
3.3. Placement
Antenna Consideraons
The characteriscs of the internal antenna should be considered when choosing the
placement and orientaon of the unit.
Required Distance Between Devices
For opmal recepon, cellular devices should not be conned in buildings made of
concrete or metal, without windows.
To avoid interference, a minimum distance of 50 cm between cellular devices should be
observed.
At least 20 cm separaon distance between the device and the user’s body must be
maintained at all mes.
Preparaon Anybus® Wireless Bolt LTE™
SP2868 Version 1.2 Page 5 of 28

3.4. SIM Card
Prepaid Data Plan
If a prepaid data plan is used, ensure that:
• the data amount is sucient
• that any SMS nocaons are sent to a monitored number
3.5. Network Operator Cered Firmware
You may need to install a rmware cered for the operator you are going to use, it is not
possible to connect the Bolt LTE to the operator network otherwise.
Before you start to congure the Bolt LTE sengs:
• Ensure that the current rmware installed on the Bolt LTE is valid for the network
operator you are going to use.
• You nd the rmware version number in the Bolt LTE built-in web interface Overview
page. See Bolt LTE Built-In Web Interface (page 19).
• If you need to install a rmware version cered for your network operator:
Download the rmware update le, specic for your network operator, from
www.anybus.com/support.
• For informaon on how to update the rmware, see the Bolt LTE User Manual.
3.6. Firewall and Roung
There are roung opons set for the system.
By default, the rewall allow roung of:
• Outgoing trac for TCP, UDP and ICMP (for IPv4 only).
• Incoming trac for already established connecons only.
For other possible conguraons, see the Bolt LTE User Manual.
Anybus® Wireless Bolt LTE™SIM Card
Page 6 of 28 SP2868 Version 1.2

4. Installaon
4.1. Install SIM Card
NOTE
Supported SIM card types are Nano SIM for IoT and M2M, for data
communicaon, as well as standard mobile phone Nano SIM.
Figure 1. Insert SIM card
To connect Bolt LTE to a cellular data network, install a cellular SIM card:
1. Insert a SIM card into the Bolt LTE SIM card holder.
NOTE
Ensure that the SIM card contact surface is facing towards the
Ethernet port.
Installaon Anybus® Wireless Bolt LTE™
SP2868 Version 1.2 Page 7 of 28

4.2. Mechanical Installaon
Placement
• The device is intended to be mounted on top of a machine or cabinet through an M50
(50.5mm) hole using the included sealing ring and nut.
• The top mounng surface, in contact with the sealing, must be at with a nish
equivalent to Ra 3.2 or ner and cleaned and free from oils and greases.
• For opmal recepon, cellular devices require a zone around them clear of objects that
could obstruct or reect the signal.
To avoid interference, a minimum distance of 50 cm between Bolt LTE and other cellular
devices should be observed.
Installaon
IMPORTANT
Make sure that the sealing ring is correctly placed in the circular groove in
the top part of the housing before ghtening the nut.
IMPORTANT
Always hold the BOTTOM part of the unit when unghtening the nut, not
the top part (the cap).
Tightening torque: 5 Nm ±10 %
Anybus® Wireless Bolt LTE™Mechanical Installaon
Page 8 of 28 SP2868 Version 1.2