HMS Anybus Wireless Bolt RJ45 PoE User manual

Anybus
®Wireless Bolt™RJ45 PoE
USER MANUAL
SCM-1202-088 EN 1.1 ENGLISH

Important User Information
Liability
Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB of any
inaccuracies or omissions. The data and illustrations found in this document are not binding. We, HMS Industrial
Networks AB, reserve the right to modify our products in line with our policy of continuous product development.
The information in this document is subject to change without notice and should not be considered as a
commitment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no responsibility for any errors
that may appear in this document.
There are many applications of this product. Those responsible for the use of this device must ensure that all the
necessary steps have been taken to verify that the applications meet all performance and safety requirements
including any applicable laws, regulations, codes, and standards.
HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems that
may arise as a result from the use of undocumented features, timing, or functional side effects found outside the
documented scope of this product. The effects caused by any direct or indirect use of such aspects of the product
are undefined, and may include e.g. compatibility issues and stability issues.
The examples and illustrations in this document are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular implementation, HMS Industrial Networks AB cannot
assume responsibility for actual use based on these examples and illustrations.
Intellectual Property Rights
HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product
described in this document. These intellectual property rights may include patents and pending patent applications
in the USA and other countries.
Anybus®is a registered trademark and Wireless Bolt™is a trademark of HMS Industrial Networks AB. All other
trademarks mentioned in this document are the property of their respective holders.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1
Table of Contents Page
1 Preface ............................................................................................................................... 3
1.1 About This Document.....................................................................................................3
1.2 Document History ..........................................................................................................3
1.3 Document Conventions ..................................................................................................4
2 Description ....................................................................................................................... 5
2.1 Product Description........................................................................................................5
2.2 Bluetooth or WLAN? ......................................................................................................5
2.3 Model Name – Certification Identifier ...............................................................................6
3 Installation ........................................................................................................................ 7
3.1 Safety ...........................................................................................................................7
3.2 General Information .......................................................................................................7
3.3 Mechanical Installation ...................................................................................................8
3.4 Connectors....................................................................................................................9
3.5 RJ45 LED Indicators ....................................................................................................10
3.6 RESET Button ............................................................................................................. 11
4 Configuration ................................................................................................................. 12
4.1 General.......................................................................................................................12
4.2 Web Interface ..............................................................................................................13
4.3 Factory Restore ...........................................................................................................28
A Configuration Examples.............................................................................................. 29
A.1 Ethernet Bridge via WLAN or Bluetooth®........................................................................29
A.2 PROFINET networking via Bluetooth®............................................................................30
A.3 EtherNet/IP™Networking via Bluetooth®.........................................................................31
A.4 Ethernet network to existing WLAN ...............................................................................32
A.5 Adding single Ethernet node to WLAN ...........................................................................33
A.6 Accessing PLC via WLAN from Handheld Device ...........................................................34
B Wireless Technology Basics ...................................................................................... 36
C Technical Data................................................................................................................ 37
C.1 Hardware Specifications...............................................................................................37
C.2 Communication ...........................................................................................................38

This page intentionally left blank

Preface 3 (40)
1 Preface
1.1 About This Document
This manual describes how to install and configure Anybus Wireless Bolt RJ45 PoE.
For additional documentation and software downloads, FAQs, troubleshooting guides and
technical support, please visit www.anybus.com/support.
1.2 Document History
Version Date Description
1.0 2018-04-23 First release
1.1 2018-09-05 Updated for FW 1.6.3
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Preface 4 (40)
1.3 Document Conventions
Ordered lists are used for instructions that must be carried out in sequence:
1. First do this
2. Then do this
Unordered (bulleted) lists are used for:
• Itemized information
• Instructions that can be carried out in any order
...and for action-result type instructions:
► This action...
➨leads to this result
Bold typeface indicates interactive parts such as connectors and switches on the hardware, or
menus and buttons in a graphical user interface.
Monospaced text is used to indicate program code and other
kinds of data input/output such as configuration scripts.
This is a cross-reference within this document: Document Conventions, p. 4
This is an external link (URL): www.hms-networks.com
This is additional information which may facilitate installation and/or operation.
This instruction must be followed to avoid a risk of reduced functionality and/or
damage to the equipment, or to avoid a network security risk.
Caution
This instruction must be followed to avoid a risk of personal injury.
WARNING
This instruction must be followed to avoid a risk of death or serious injury.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Description 5 (40)
2 Description
2.1 Product Description
Anybus Wireless Bolt RJ45 PoE provides wireless communication over WLAN and/or
Bluetooth®to Ethernet networks.
It supports Power over Ethernet (PoE) in compliance with IEEE 802.3af/at, type 1 class 0
(<12 W), both midspan and endspan. It can optionally be connected to a separate 19–36 VDC
power source for redundancy.
Typical applications for Anybus Wireless Bolt RJ45 PoE include:
• Adding wireless cloud connectivity to industrial devices
• Accessing devices from a laptop, smartphone or tablet
• Ethernet cable replacement between devices
Note:
Bluetooth PAN (Personal Area Network) may not work with some devices due to different
implementations of Bluetooth by different manufacturers.
WLAN 5 GHz cannot be used at the same time as WLAN 2.4 GHz or Bluetooth.
2.2 Bluetooth or WLAN?
Use Bluetooth when...
• ...the wireless link has an Anybus Wireless Bridge II or Anybus Wireless Bolt at both ends.
• ...an interruption-free connection is more important than data throughput speed.
• ...interference robustness is important – e.g. in an industrial environment.
• ...a Profinet I/O cycle time or EtherNet/IP RPI of 64 ms or more is acceptable.
Use WLAN when...
• ...connecting to other types of wireless devices or a WLAN infrastructure.
• ...high data throughput speed is more important than connection reliability.
• ...large file transfers are expected.
• ...WLAN channel frequency planning is possible.
• ...a low Profinet I/O cycle time or EtherNet/IP RPI is desired.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Description 6 (40)
2.3 Model Name – Certification Identifier
The model name consists of a model prefix followed by two designators for interface
configuration and functionality.
Prefix AWB2 Anybus Wireless Bolt
Interface configuration A
B
Interface 18-pin socket
Interface RJ45 and 3-pin power socket
Functionality A
B
C
Ethernet
Ethernet and RS232/485
Ethernet and CAN
Example: AWB2AA = Anybus Wireless Bolt with18-pin plug connector and Ethernet
networking only.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Installation 7 (40)
3 Installation
3.1 Safety
Caution
This equipment emits RF energy in the ISM (Industrial, Scientific, Medical) band.
Make sure that all medical devices used in proximity to this device meet appropriate
susceptibility specifications for this type of RF energy.
This product is recommended for use in both industrial and domestic environments.
For industrial environments it is mandatory to use the functional earth connection to
comply with immunity requirements. For domestic environments the functional earth
must be used if a shielded Ethernet cable is used, in order to meet emission
requirements.
This product contains parts that can be damaged by electrostatic discharge (ESD).
Use ESD prevention measures to avoid damage.
See also additional safety instructions in the included compliance information.
3.2 General Information
Make sure that you have all the necessary information about the capabilities and restrictions of
your local network environment before installation.
The characteristics of the internal antenna should be considered when choosing the placement
and orientation of the unit.
For optimal reception, wireless devices require a zone between them clear of objects that could
otherwise obstruct or reflect the signal. A minimum distance of 50 cm between the devices
should also be observed to avoid interference.
See also Wireless Technology Basics, p. 36.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Installation 8 (40)
3.3 Mechanical Installation
The device is intended to be mounted on top of a machine or cabinet through an M50
(50.5 mm) hole using the included sealing ring and nut.
The top mounting surface (in contact with the sealing) must be flat with a finish equivalent to
Ra 3.2 or finer and cleaned and free from oils and greases.
Tightening torque: 5 Nm ±10 %.
Make sure that the sealing ring is correctly placed in the circular groove in the top
part of the housing before tightening the nut.
Always hold the BOTTOM part of the unit when untightening the nut, not the top
part (the cap).
Fig. 1 Installation drawing
All measurements are in mm.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Installation 9 (40)
3.4 Connectors
Fig. 2 Connectors
Connecting power with reverse polarity or using the wrong type of power supply
may damage the equipment. Make sure that the power supply is connected
correctly and of the recommended type.
See also Technical Data, p. 37 regarding power supply requirements.
Power Connector (3-pin terminal block)
Pin Function
1+19–36 VDC
2-
3 Functional Earth (FE)
FE must be connected on the power connector if not using PoE.
Ethernet Connector (RJ45 PoE)
Pin Data PoE
1 TD+ A+ Positive power from alt. A PSE
2 TD- A+
3 RD+ A- Negative power from alt. A PSE (with pin 6)
4 B+ Positive power from alt. B PSE
5 B+
6 RD- A- Negative power from alt. A PSE (with pin 3)
7 B- Negative power from alt. B PSE
8 B-
Housing Shield Functional Earth (FE)
via 1 nF capacitor and 1 MΩ bleeder resistor
Shielded or unshielded Ethernet cables may be used.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Installation 10 (40)
3.5 RJ45 LED Indicators
Fig. 3 RJ45 LED indicators
LED A – LINK/ACTIVITY Function
Off No Ethernet link or no power
Yellow Ethernet link established
Yellow, flashing Ethernet traffic
LED B – STATUS Function
Off No power
Blue Connected on all configured wireless interfaces
Purple Trying to connect to WLAN/Bluetooth access point
Blue, slow blink Awaiting connections
Alternating blue/purple Connected on one interface and trying to connect or awaiting connections on
another
Purple, slow blink Awaiting connections on one interface and trying to connect on another
Purple, fast blink Scanning for Bluetooth devices or WLAN networks
Red, slow blink No configured wireless interface
Red Recoverable/unrecoverable fault
Anybus
®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Installation 11 (40)
3.6 RESET Button
Fig. 4
The RESET button is located on the bottom of the unit.
When the unit is powered on, press and hold RESET for >10 seconds and then release it to
reset to the factory default settings.
Recovery Mode
If the web interface cannot be accessed, the unit can be reset by starting in Recovery Mode
and reinstalling the firmware using Anybus Firmware Manager II, which can be downloaded
from www.anybus.com/support.
To enter Recovery Mode, press and hold RESET during startup.
Firmware updates should normally be carried out through the web interface.
Recovery Mode should only be used if the unit is unresponsive and the web
interface cannot be accessed.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Configuration 12 (40)
4 Configuration
4.1 General
Anybus Wireless Bolt RJ45 PoE should normally be configured via the web interface.
Parameters can be set individually or using one of the pre-configured Easy Config modes.
The web interface is accessed by pointing a web browser to the IP address of the Wireless Bolt.
The default address is 192.168.0.99. The computer accessing the web interface must be in the
same IP subnet as the Wireless Bolt.
Fig. 5 Web interface
Advanced configuration can be carried out by issuing AT (modem) commands through the web
interface or over a Telnet or RAW TCP connection to port 8080. See the AT Commands
Reference Guide or the Help page in the web interface for more information.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Configuration 13 (40)
4.2 Web Interface
4.2.1 System Overview
Fig. 6 System Overview page
The System Overview page shows the current settings and connection status for the wired
and wireless interfaces. The different parameters are explained in the descriptions of each
settings page in this manual.
The Help page describes AT commands that can be used for advanced configuration.
Save and Reboot This button will be enabled if the unit must be restarted to apply a change.
Cancel All Changes Resets parameter changes that have not been applied.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Configuration 14 (40)
4.2.2 Easy Config
Fig. 7 Easy Config page
To activate an Easy Config mode, select it from the dropdown menu and click on Set. The
mode will be activated immediately.
Easy Config Modes
EC Role Description
1Bluetooth PANU Configure as Bluetooth client and scan for another client (PANU–PANU).
2–Reset configuration to factory defaults.
3–Reset IP settings to factory defaults.
4Client Wait for automatic configuration.
5WLAN AP Configure units in mode 4 as clients.
Restart as access point and connect clients.
6Bluetooth NAP
7WLAN AP Configure units in mode 4 as clients.
Restart as access point and connect clients.
Apply PROFINET optimization to all units.
8Bluetooth NAP
9Bluetooth PANU Configure as Bluetooth client and scan for another client (PANU–PANU).
Apply PROFINET optimization to both units.
10 (any) Apply PROFINET optimization and restart.
11 (any) Enable PROFIsafe mode.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Configuration 15 (40)
Notes:
• Mode 1 will scan for units in mode 4. When a unit in mode 4 is detected, the scanning unit
will configure itself as a Bluetooth PANU client, send a connection configuration to the
detected unit, and restart. The detected unit will also restart and attempt to connect to the
first unit as a PANU client.
• Modes 5, 6, 7 and 8 will scan for units in mode 4. The detected units will be reconfigured as
clients and the scanning unit will restart as an access point. The clients will then restart and
connect to the access point.
• Modes 7 and 8 will additionally apply PROFINET optimization to all the units. PROFINET
messages will then have priority over TCP/IP frames.
• Mode 11 locks the unit in PROFIsafe mode where the configuration cannot be changed
without physical access. To cancel this mode the unit must be restored to factory defaults
by pressing and holding the RESET button.
• Modes 10 and 11 will be added to the configuration without changing any other settings.
• Modes 1 and 9 will listen for 40 seconds or until a configuration is established.
• Modes 4 will listen for 120 seconds or until receiving a configuration.
• Modes 5, 6, 7 and 8 will time out after 120 seconds.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Configuration 16 (40)
4.2.3 Network Settings
Fig. 8 Network Settings page
IP Assignment Select static or dynamic IP addressing (DHCP)
IP Address Static IP address for the unit
The browser should automatically be redirected to the new address after clicking
on Save and Reboot (not supported by all browsers).
Subnet Mask Subnet mask when using static IP
Default Gateway Default gateway when using static IP
Internal DHCP Server Disabled: No internal DHCP functionality
DHCP Relay Enabled: The unit can receive a DHCP request on one interface and
resend it to a DHCP server located on one of the other interfaces.
Only a single DHCP server can be active for all the connected interfaces.
If WLAN is used, the forwarding mode must be set to Layer 3 IP Forward.
DHCP Server Enabled: Activates an internal DHCP server. This option is only
available when IP Assignment is set to Static.
Do not enable this option if there is already a DHCP server on the network!
Start Address (Y) The internal DHCP server will assign up to 7 IP addresses starting from X.X.X.Y,
where Xis taken from the current static IP address setting, and Yis the value in
Start Address. Already allocated addresses will be skipped, including the address
of the unit itself. The subnet mask setting will be ignored.
Examples:
IP Address: 192.168.0.99, Start Address: 101
DHCP range = 192.168.0.101 – 192.168.0.107
IP Address: 192.168.0.103, Start Address: 101
DHCP range = 192.168.0.101 – 192.168.0.108
7 addresses are allocated but the address of the unit is skipped.
Anybus
®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Configuration 17 (40)
4.2.4 WLAN Settings - Client
Fig. 9 WLAN Settings - Client
Enable Enable/disable the WLAN interface.
Operating Mode Choose operation as WLAN Client or Access Point. If Access Point is selected,
additional settings will be available.
Channel Bands Choose to scan only the 2.4 GHz or 5 GHz channel band, or both (default).
The unit can be configured to scan on both the 2.4 GHz and 5 GHz channel bands but can only
communicate on one band at a time.
Scan for Networks Click to scan the selected frequency band(s) for discoverable WLAN networks.
Select a network from the dropdown menu to connect to it.
Connect to SSID To connect manually to a network, enter its SSID (network name) here. This can
be used if the network does not broadcast its SSID.
Authentication Mode Select the authentication/encryption mode required by the network.
Open = No encryption or authentication
Passkey Enter the passkey when using WPA/WPA2-PSK or WEP64/128.
Username, Domain,
Passphrase
Authentication details when using LEAP or PEAP (WPA2 Enterprise).
Channel Select a specific channel to use when scanning for networks.
Auto = all available channels will be scanned (default).
See also WLAN Channels and World Mode (Client Mode only), p. 19
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1

Configuration 18 (40)
Advanced Settings
Bridge Mode Layer 2 tunnel = All layer 2 data will be bridged over WLAN.
Use when multiple devices on both sides of an Ethernet network bridge must be
able to communicate via WLAN (many-to-many).
Only works between Anybus Wireless Bolt or Wireless Bridge II devices.
Layer 2 cloned MAC only = Layer 2 data from only a single MAC address
(specified below) will be bridged over WLAN (many-to-one).
Layer 3 IP forward (default) = IP data from all devices will be bridged over WLAN.
This mode must be used when using the DHCP Relay function.
Cloned MAC Address The MAC address to use with Layer 2 cloned MAC only (see above).
WLAN Roaming
Anybus Wireless Bolt RJ45 PoE supports Fast Roaming according to IEEE 802.11r. This
enables a WLAN client to roam quicker between WLAN Access Points that have the same
SSID and support IEEE 802.11r. Fast Roaming is enabled as default but can be permanently
disabled using AT commands.
When Fast Roaming is disabled the client will be able to roam between all access points that
have been specified with SSID, BSSID and Channel in a connection list (using AT commands).
When Fast Roaming is enabled only the first access point SSID in the list will be used, and the
BSSID and Channel parameters are ignored. If the access point does not support IEEE 802.11r
the client will continue without Fast Roaming.
See the AT Commands Reference Guide or the Help page in the web interface for more
information about how to set up WLAN roaming.
Anybus®Wireless Bolt™RJ45 PoE User Manual SCM-1202-088 EN 1.1