HMS Anybus Wireless Bridge II User guide

Anybus®Wireless Bridge II™
STARTUP GUIDE
SCM-1202-013/SP2167-EN 1.7 ENGLISH

Important User Information
Liability
Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB
of any inaccuracies or omissions. The data and illustrations found in this document are not binding. We,
HMS Industrial Networks AB, reserve the right to modify our products in line with our policy of continuous
product development. The information in this document is subject to change without notice and should not
be considered as a commitment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no
responsibility for any errors that may appear in this document.
There are many applications of this product. Those responsible for the use of this device must ensure that
all the necessary steps have been taken to verify that the applications meet all performance and safety re-
quirements including any applicable laws, regulations, codes, and standards.
HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems
that may arise as a result from the use of undocumented features, timing, or functional side effects found
outside the documented scope of this product. The effects caused by any direct or indirect use of such as-
pects of the product are undefined, and may include e.g. compatibility issues and stability issues.
The examples and illustrations in this document are included solely for illustrative purposes. Because of the
many variables and requirements associated with any particular implementation, HMS Industrial Networks
AB cannot assume responsibility for actual use based on these examples and illustrations.
Intellectual Property Rights
HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product
described in this document. These intellectual property rights may include patents and pending patent ap-
plications in the USA and other countries.
Anybus®is a registered trademark and Wireless Bridge II™is a trademark of HMS Industrial Networks AB.
All other trademarks mentioned in this document are the property of their respective holders.
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7

Preparation 3 (16)
1 Preparation
1.1 About This Document
This document describes how to install Anybus Wireless Bridge II and set up a
basic configuration.
For additional documentation, configuration examples, FAQs, troubleshooting
guides and technical support, please visit www.anybus.com/support.
1.2 Product Description
Anybus Wireless Bridge II provides wireless communication over WLAN and/or
Bluetooth®to wired networks.
Typical applications for Anybus Wireless Bridge II include:
• Adding wireless cloud connectivity to industrial devices
• Accessing devices from a laptop, smartphone or tablet
• Ethernet cable replacement between devices
Limitations:
Bluetooth PAN (Personal Area Network) may not work with some devices due to
different implementations of Bluetooth by different manufacturers.
WLAN 5 GHz cannot be used at the same time as WLAN 2.4 GHz or Bluetooth.
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7

Preparation 4 (16)
1.3 Model Name – Certification Identifier
The model name is used to identify the product for various certifications. It con-
sists of a model prefix followed by two designators for the specific interface con-
figuration and functionality.
Prefix AWB3 Anybus Wireless Bridge II
Interface configuration A
B
Internal antenna (Closed Type), interfaces:
Dual M12
External antenna (Open Type), interfaces:
Dual M12, RP-SMA
Functionality A
B
Ethernet with digital input
Ethernet w/o digital input
Example: AWB3AA = Anybus Wireless Bridge II with internal antenna, Ethernet
networking and digital input.
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7

Installation 5 (16)
2 Installation
Caution
This equipment emits RF energy in the ISM (Industrial, Scientific,
Medical) band. Make sure that all medical devices used in proximity to
this device meet appropriate susceptibility specifications for this type of
RF energy.
Caution
The M12 power and LAN connectors must be provided with tool
operated mechanical lock nuts that are tightened by the installer.
This product is recommended for use in both industrial and domestic
environments. For industrial environments it is mandatory to use the
functional earth connection to comply with immunity requirements. For
domestic environments the functional earth must be omitted if a shielded
Ethernet cable is used, in order to meet emission requirements.
This product contains parts that can be damaged by electrostatic
discharge (ESD). Use ESD prevention measures to avoid damage.
Anybus Wireless Bridge II can be screw-mounted directly onto a flat surface or
mounted on a standard DIN rail using the optional DIN mounting kit.
Make sure that you have all the necessary information about the capabilities and
restrictions of your local network environment before installation.
For optimal reception, wireless devices require a zone between them clear of ob-
jects that could otherwise obstruct or reflect the signal. A minimum distance of
50 cm between the devices should also be observed to avoid interference.
The characteristics of the internal antenna should be considered when choosing
the placement and orientation of the unit (unless an external antenna is used).
See the Anybus Wireless Bridge II User Manual for more information.
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7

Installation 6 (16)
2.1 Dimensions
All measurements are in mm.
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7

Installation 7 (16)
2.2 Connectors
Power Connector (A-coded male M12)
Pin Function
1 Power + (9–30 V)
2 Digital Input Ground
3 Power Ground
4 Digital Input + (9–30 V)
5 Functional Earth
Signal wiring for the digital input must be carried in the same cable as
power and functional earth if wiring length exceeds 3 meters.
LAN Connector (D-coded female M12)
Pin Function Color coding (T568B)
1 Transmit + Orange/White
2 Receive + Green/White
3 Transmit - Orange
4 Receive - Green
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7

Installation 8 (16)
2.3 LED Indicators
PWR Off No power
Green Normal operation
WLAN
Off WLAN disabled or no power
Blue, blinking Access Point: No clients, awaiting connections
Blue Access Point: Connected to at least one client
Client: Connected to access point
Blue, flickering WLAN data activity (when connected)
Purple, blinking Client: Scanning for access points
Purple Client: Connecting to a detected access point
Red Unrecoverable error
LAN
Off No Ethernet connection
Yellow Ethernet link present
Yellow, flickering Ethernet data activity (when connected)
BT
Off Bluetooth disabled or no power
Blue, blinking NAP: No clients, awaiting connections
Blue NAP: Connected to at least one PANU client
PANU: Connected to NAP
Blue, flickering Bluetooth data activity (when connected)
Purple PANU: Trying to connect to NAP
Red Unrecoverable error
RSSI (WLAN Client) / Link Quality (Bluetooth PANU)
No connection
A RSSI/Link Quality < 25 %
A B RSSI/Link Quality 25–50 %
A B C RSSI/Link Quality 50–75 %
A B C D RSSI/Link Quality > 75 %
Additional LED indications are used when the unit is in Recovery Mode.
See Recovery Mode LED Indications, p. 12.
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7

Configuration 9 (16)
3 Configuration
Anybus Wireless Bridge II can be configured via the web interface or using one
of the pre-configured Easy Config modes.
Advanced configuration can be carried out by issuing AT commands via the web
interface or over a Telnet or RAW TCP connection to port 8080.
3.1 The Web Interface
The web interface is accessed by pointing your web browser to the IP address of
the Wireless Bridge. The default address is 192.168.0.99.
Most configuration settings are self-explanatory. See also the Anybus Wireless
Bridge II User Manual.
The web interface is designed for the current stable versions of Internet
Explorer, Chrome, Firefox and Safari. Other browser versions may not
support all functions of the interface.
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7

Configuration 10 (16)
3.2 Easy Config
1. Power on the unit and wait for the Link Quality LEDs to light up and go out
again, then immediately press and release the MODE button.
2. Press MODE repeatedly to cycle through the Easy Config modes until the
desired mode is indicated by the A-B-C-D LEDs.
3. Within 20 seconds of step 2, press and hold MODE for 2 seconds. When the
button is released the unit will restart in the selected mode.
Easy Config Modes
Mode Role Description LED
2 — Reset configuration to factory defaults. B
3 — Reset IP settings to factory defaults. A B
4 Client Wait for automatic configuration. C
5 WLAN AP Configure units in mode 4 as clients.
Restart as access point and connect clients.
A C
6 Bluetooth NAP B C
7 WLAN AP Configure units in mode 4 as clients.
Restart as access point and connect clients.
Apply PROFINET optimizations to all units.
A B C
8 Bluetooth NAP D
10 — Apply PROFINET optimizations and restart. B D
Modes 5 – 8 will scan for units in mode 4. Detected units will be reconfigured as
clients, and the scanning unit will restart as an access point. The clients will then
restart and connect to the access point.
Modes 7 and 8 will additionally apply PROFINET optimization to all the units.
PROFINET messages will then have priority over TCP/IP frames.
Mode Timeout
• Modes 5 – 8 will time out after 120 seconds. Apply the mode again to repeat
the scan.
• Mode 4 will listen for 120 seconds or until receiving a configuration.
The IP address of a client may be changed by the configuration from the
access point. Active browser sessions could therefore be lost.
Anybus®Wireless Bridge II™Startup Guide SCM-1202-013/SP2167-EN 1.7