HMS Anybus Wireless Bridge II User guide

Anybus®Wireless Bridge II™
STARTUP GUIDE
SP2167 2.1 en-US ENGLISH

Important User Information
Disclaimer
The information in this document is for informational purposes only. Please inform HMS Networks of any
inaccuracies or omissions found in this document. HMS Networks disclaims any responsibility or liability
for any errors that may appear in this document.
HMS Networks reserves the right to modify its products in line with its policy of continuous product
development. The information in this document shall therefore not be construed as a commitment on
the part of HMS Networks and is subject to change without notice. HMS Networks makes no
commitment to update or keep current the information in this document.
The data, examples and illustrations found in this document are included for illustrative purposes and are
only intended to help improve understanding of the functionality and handling of the product. In view of
the wide range of possible applications of the product, and because of the many variables and
requirements associated with any particular implementation, HMS Networks cannot assume
responsibility or liability for actual use based on the data, examples or illustrations included in this
document nor for any damages incurred during installation of the product. Those responsible for the use
of the product must acquire sufficient knowledge in order to ensure that the product is used correctly in
their specific application and that the application meets all performance and safety requirements
including any applicable laws, regulations, codes and standards. Further, HMS Networks will under no
circumstances assume liability or responsibility for any problems that may arise as a result from the use
of undocumented features or functional side effects found outside the documented scope of the product.
The effects caused by any direct or indirect use of such aspects of the product are undefined and may
include e.g. compatibility issues and stability issues.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

About This Document 3 (18)
1 About This Document
This document describes how to install Anybus Wireless Bridge II and set up a
basic configuration.
For additional documentation, configuration examples, FAQs, troubleshooting
guides and technical support, please visit www.anybus.com/support.
1.1 Document Conventions
The following conventions are used to indicate safety information and other
important content in this document:
WARNING
Instruction that must be followed to avoid a risk of death or serious injury.
Caution
Instruction that must be followed to avoid a risk of personal injury.
Instruction that must be followed to avoid a risk of reduced functionality
and/or damage to the equipment, or to avoid a network security risk.
Additional information which may facilitate installation and/or operation.
1.2 Trademarks
Anybus®is a registered trademark and Wireless Bridge II™is a trademark of HMS
Industrial Networks AB. All other trademarks mentioned in this document are
the property of their respective holders.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Safety 4 (18)
2 Safety
2.1 General Safety Instructions
Caution
This equipment emits RF energy in the ISM (Industrial, Scientific, Medical)
band. Make sure that all medical devices used in proximity to this
equipment meet appropriate susceptibility specifications for this type of
RF energy.
Caution
The M12 power and LAN connectors must be provided with tool
operated mechanical lock nuts that are tightened by the installer.
This equipment is recommended for use in both industrial and domestic
environments. For industrial environments it is mandatory to use the
functional earth connection to comply with immunity requirements. For
domestic environments the functional earth must be used if a shielded
Ethernet cable is used, in order to meet emission requirements.
This equipment contains parts that can be damaged by electrostatic
discharge (ESD). Use ESD prevention measures to avoid damage.
2.2 External Antenna Restrictions
For models with external antenna, only use antennas that are certified for use
with this equipment. Using external antennas that are not certified for use with
this equipment will invalidate its certifications and make it non-compliant with
the regulations for radio equipment.
A list of certified antennas can be found at www.anybus.com/support.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Safety 5 (18)
2.3 Intended Use
The intended use of this equipment is as a communication interface and
gateway. The equipment receives and transmits data on various physical levels
and connection types.
If this equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
2.4 Type Identification
The type name consists of a type prefix followed by two designators for
interface configuration and functionality.
Prefix AWB3 Anybus Wireless Bridge II
Interface configuration A
B
Internal antenna, Dual M12
External antenna, Dual M12, RP-SMA
Functionality A
B
Ethernet with digital input
Ethernet w/o digital input
Example: AWB3AA = Anybus Wireless Bridge II with internal antenna, Ethernet
networking and digital input.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Installation 6 (18)
3 Installation
3.1 General Information
Anybus Wireless Bridge II can be screw-mounted directly onto a flat surface or
mounted on a standard DIN rail using the optional DIN mounting kit.
For optimal reception, wireless devices require a zone between them clear of
objects that could otherwise obstruct or reflect the signal. A minimum distance
of 50 cm between the devices should also be observed to avoid interference.
For models with internal antenna the characteristics of the antenna should be
considered when choosing the placement and orientation of the unit. See the
User Manual for more information about the antenna characteristics for this
equipment.
Make sure that you have all the necessary information about the capabilities
and restrictions of your local network environment before installation.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Installation 7 (18)
3.2 Connectors
Power Connector (A-coded male M12)
Pin Function
1Power + (9–30 V)
2Digital Input Ground
3Power Ground
4Digital Input + (9–30 V)
5Functional Earth
The digital input can be used for additional functionality with advanced
configurations and to remotely reset the unit.
If voltage is applied to the digital input for more that 10 seconds the unit
will be reset to factory defaults.
Signal wiring for the digital input must be carried in the same cable as
power and functional earth if wiring length exceeds 3 meters.
See www.anybus.com/support for more information about the digital input.
LAN Connector (D-coded female M12)
Pin Function Color coding (T568B)
1 Transmit + Orange/White
2 Receive + Green/White
3 Transmit - Orange
4 Receive - Green
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Installation 8 (18)
3.3 LED Indicators
3.3.1 Status Indicators
LED Indication Description
PWR Off No power
Green Normal operation
WLAN
Off WLAN disabled or no power
Blue, blinking Access Point: No clients, awaiting connections
Blue Access Point: Connected to at least one client
Client: Connected to access point
Blue, flickering WLAN data activity (when connected)
Purple, blinking Client: Scanning for access points
Purple Client: Connecting to a detected access point
Red Unrecoverable error
LAN
Off No Ethernet connection
Yellow Ethernet link present
Yellow, flickering Ethernet data activity (when connected)
BT
Off Bluetooth disabled or no power
Blue, blinking NAP: No clients, awaiting connections
Blue NAP: Connected to at least one PANU client
PANU: Connected to NAP
Blue, flickering Bluetooth data activity (when connected)
Purple PANU: Trying to connect to NAP
Red Unrecoverable error
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Installation 9 (18)
3.3.2 Link Quality/Mode Indicators
RSSI (WLAN Client) / Link Quality (Bluetooth PANU)
LED Description
No connection
ARSSI/Link Quality < 25 %
A B RSSI/Link Quality 25–50 %
A B C RSSI/Link Quality 50–75 %
A B C D RSSI/Link Quality > 75 %
These LEDs are also used when selecting an Easy Config mode and to indicate
update status in Recovery Mode.
See Easy Config, p. 12 and Recovery Mode LED Indications, p. 10.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Installation 10 (18)
3.4 MODE Button
The MODE button can be used to restart or reset the unit as well as for
selecting an Easy Config mode.
When the unit is powered on, press and hold MODE for >10 seconds and then
release it to reset to the factory default settings.
Recovery Mode
If the web interface cannot be accessed, the unit can be reset by starting in
Recovery Mode and reinstalling the firmware using Anybus Firmware Manager
II, which can be downloaded from www.anybus.com/support.
To enter Recovery Mode, press and hold RESET during startup.
Firmware updates should normally be carried out through the web
interface. Recovery Mode should only be used if the unit is unresponsive
and the web interface cannot be accessed.
Recovery Mode LED Indications
In Recovery Mode the Status LEDs will indicate firmware update status:
PWR Green Firmware update in progress
Green, blinking Waiting for valid firmware
WLAN +BT Alternating red/blue Firmware update in progress
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Configuration 11 (18)
4 Configuration
Anybus Wireless Bridge II is normally configured via the web interface or using
one of the pre-configured Easy Config modes.
Advanced configuration can be carried out by issuing AT commands via the web
interface or over a Telnet or RAW TCP connection to port 8080.
4.1 Web Interface
The web interface is accessed by pointing a web browser to the IP address of
the unit. The default address is 192.168.0.99.
The configuration settings are described in detail in the User Manual.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Configuration 12 (18)
4.2 Easy Config
1. Power on the unit and wait for the Link Quality LEDs to light up and go out
again, then immediately press and release the MODE button.
2. Press MODE repeatedly to cycle through the Easy Config modes until the
desired mode is indicated by the A-B-C-D LEDs.
3. Within 20 seconds of step 2, press and hold MODE for 2 seconds. When
the button is released the unit will restart in the selected mode.
4.2.1 Easy Config Modes
EC LED Role Description
1A Bluetooth PANU Configure as a client and scan for
another client (PANU to PANU).
2B–Reset configuration to factory defaults.
3A B –Reset IP settings to factory defaults.
4CClient Wait for automatic configuration.
5A C WLAN AP Configure units in mode 4 as clients.
Restart as access point and connect
clients.
6B C Bluetooth NAP
7A B C WLAN AP Configure units in mode 4 as clients.
Restart as access point and connect
clients.
Apply PROFINET optimization to all units.
8D Bluetooth NAP
9A D Bluetooth PANU
Configure as a client and scan for
another client (PANU to PANU).
Apply PROFINET optimization to both
units.
10 B D (any) Apply PROFINET optimization and
restart.
11 A B D (any) Enable PROFIsafe mode.
The Easy Config modes are also described when selected in the web interface.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Configuration 13 (18)
4.3 I/O-Data Cycle Time
Based on recommendations from industrial equipment suppliers, such as
Rockwell and Siemens, it is recommended to use the following minimum I/O-
data cycle times for PROFINET and EtherNet/IP networks:
• Wireless link Point-to-Point with Bluetooth PANU-PANU or Wi-Fi Access
Point to Station: 32 ms
• Wireless link with Access Point and up to 4 wireless clients/stations,
Bluetooth or Wi-Fi: 64 ms
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Configuration 14 (18)
4.4 Factory Restore
Any one of these actions will restore the factory default settings:
• Clicking on Factory Restore on the System Settings page
• Executing Easy Config Mode 2
• Issuing the AT command AT&F and then restarting the unit
• Holding MODE pressed for >10 seconds and then releasing it
• Applying voltage to the digital input for >10 seconds
Default Network Settings
IP Assignment Static
IP Address 192.168.0.99
Subnet Mask 255.255.255.0
Default Gateway 192.168.0.99
Internal DHCP Server Disabled
DHCP Interfaces All
Default WLAN Settings
Operating Mode Client
Channel Bands 2.4 GHz & 5 GHz
Authentication Mode WPA/WPA2–PSK
Channel Auto
Bridge Mode Layer 3 IP forward
MIMO AWB3000: Enabled
AWB3010: Disabled
Default Bluetooth Settings
Operating Mode PANU (Client)
Local Name [generated from MAC address]
Connectable No
Discoverable No
Security Mode Just works
Bluetooth LE Operating Mode: Disabled
Connectable: No
Discoverable: No
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Technical Data 15 (18)
5 Technical Data
5.1 Hardware Specifications
Order code AWB3000 AWB3010
Wired Interface type Ethernet
Antenna 3 internal antennas:
2.4 GHz
2.4 GHz MIMO
5 GHz
1 external antenna:
2.4 GHz + 5 GHz dual band
Dimensions (LxWxH) 93 x 68 x 33.2 mm
Weight 120 g
Operating temperature -40 to +65 °C
Storage temperature -40 to +85 °C
Humidity EN 600068-2-78: Damp heat, +40 °C, 93 % humidity for 4 days
Vibration See datasheet
Housing material Plastic (see datasheet for details)
Protection class IP65
Mounting Screw mount or DIN rail using optional clip
Power connector M12 male A-coded
Ethernet connector M12 female D-coded
Power supply 9–30 VDC (-5 % +20 %)
Cranking 12 V (ISO 7637-2:2011 pulse 4)
Reverse polarity protection
Power consumption 0.7 W (idle), 1.7 W (max)
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

Technical Data 16 (18)
5.2 Installation Drawing
All measurements are in mm.
Anybus®Wireless Bridge II™Startup Guide SP2167 2.1 en-US

This page intentionally left blank

last page
© 2020 HMS Industrial Networks
Box 4126
300 04 Halmstad, Sweden
[email protected] SP2167 2.1 en-US / 2020-11-30 / 20889