Hobby King FALCON TRAINER User manual

Wing Span:73.2in/1860mm; Radio:4Channel 5Servos;
Wing Area:62sq.dm; Engine:20CC Gas
Length:61in/1550mm;
CAUTION : this plane is not a toy and should be kept away
this manual.
●First-time builders should seek advice from
p
eo
p
le havin
g
buildin
g
ex
p
erience in order to assemble the model correctl
y
and to
p
roduce its
●Assemble this kit onl
y
in
p
laces out of children’s reach!
●Take enou
g
h safet
y
p
ercautions
p
rior to o
p
eratin
g
this model.
You are res
p
onsible for this model’s assembl
y
and safe o
p
eration!
●Alwa
y
s kee
p
this instruction manual read
y
at hand for
q
uick
reference
,
even after com
p
letin
g
the assembl
y
.
children under 16 years of age! Before use , please carefully read
p
erformance to full extent .
All manuals and user guides at all-guides.com
all-guides.com

All the parts together
Main Wings
Connect the aileron and the main wing by hinges.Be sure to apply instant
type glue to both sides of each hinges.
Install the aileron horns in place with AB glue Align the holes in the horns
All manuals and user guides at all-guides.com

Cut the servo holes on the bottom of the main wings
Gather servo parts as shown.
Install the control horn.
All manuals and user guides at all-guides.com

Use screw to fixed it
Install the servo.as shown
Drill holes with the specified diameter(13mm) on the bottom wing
All manuals and user guides at all-guides.com

Servo extension through the hole
Put the servo into the hole then use screw fixed it
Connect the servo arm and control horn with push rod .
All manuals and user guides at all-guides.com

Connect the main wings and the fuselage with hard wood.
Main Landing Gear and Tail Wheel Unit
Cut hole at the Original design hole of the fuselage
Fix up main landing gear on the fuselage bottom with screws.
All manuals and user guides at all-guides.com
all-guides.com

Use screw to connect the landing gear, wheel pant, nut and wheel
in turn, and finally use a lock nut to lock them.
Finished
p
hoto
Drill holes with the specified diameter(2mm)
Stabilizer And Rudder
All manuals and user guides at all-guides.com

Use screw to lock tail landing gear on the wing bottom
Stabilizer And Rudder
Apply epoxy into hinge hole of the elevator
Connect the vertical fin and the rudder by hinges.
All manuals and user guides at all-guides.com

Cut off shaded portion on the fuselage.
Cut the holes on the stabilizer
Install the elevator and vertail fin，as shown
All manuals and user guides at all-guides.com

Install the elevator horns and fix it with screws.
Finished photo
Install rudder horns and push-rod.
All manuals and user guides at all-guides.com

Assemble the elevator servos in the fuselage
Install the rudder servo and fix it with screws.
Install throttle servo and push-rod
All manuals and user guides at all-guides.com
all-guides.com

Screwed to the wing.As shown.
Trim fit the canopy
Use screw to lock it
All manuals and user guides at all-guides.com

Drill a hole use for install adjustable engine mounts
Fixed with nuts
Finished photo
All manuals and user guides at all-guides.com

Install the engine.as shown
Mount the fuel tank into the fuselage
CG POSITION & CONTROL THROWS
All manuals and user guides at all-guides.com

THE FINISHED PHOTO
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com
all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com