Hobby King SU-35 FIGHTER User manual

1:2O SCALE
S35FrcHrER
Please read this manual before flying.
The graphics in manual may ditferent from actual product,
Actual product as is.
ASSEMBLY MANUAL
@
Conopyxl Æt
\ [--- --T-l l/ Conopvbosexl
Front {useloge xl
:
Reor control rod x2
fl
G={
Servo x2
N
T
Front horn
IN
L-\
T
Reqr horn
n-rn
h-
Front horn hotch x2
r--)
æ
Reor horn hotch x2
Front control rod x2
j_ ,/h il
,/ i/i
All
/34 |
//
Lert wins xl
l/
%ll
.ræ il
Botterycoverho*r,
//
D Rodtixurexl ll
I
'o)\ Nut x4 I
\4 ll
@ wosrrerxs 1l
f M2 screwx4 il
bottery cover x1
G-F Rodfixturex4
n"
E \ @ N,,*r
\\
t\\
il \ \ @wosherxs
l\\
-l---: f M2screwx4
Verticol fin x2 rod x1

1.,Apply the glue evenry around the edge of the top ot tre coct<pit
(Figure lGrey part) and then arign the"upper cover with the base groove.
(Figure 1)
2. Apply glue on front fuselage edge evenly, glue canopy to fuselage.
(As shown in Figure 2)

3. Flip over the front fuselage,apply glue to the servo cut-out
then put on the servo wait for set. (Figure 3)
i]1 ."0.",o
Figure 3
4. Apply glue to the gray area as shown,put intake on it. (Figure 4)
l --
Fronl fuselage
Figure 4
i--=--_1;ffi-T
-4-

5.1. Assembly motor, propeller and motor mount as shown.
5.2. Glue motor assembly to the front fuselage. (Figure 5)
l@i
Brushlessmotors i3 ,- .) ,'
Figure 5
6. As shown in Figure, glue hatch
to inside of battery cover.
/ r r,,rr,,v,.over hatch
I E/+.*,
lJott0ry cov(n
Qlrto'Oql§on frber tubr
7. As shown in Fig.gray areas,apply glue on them,put the carbon rod
on the center of the fuselage.(Figure 6)
LJI)l)er fuselage
Carbon rod .)
.)
---I
lowil llr:rlirrle
Vertical fin
Glue
9. Apply glue on the fuselage
and put verlical fin on it.
(Figure 8)
Figure 7
Figure 8
-6-
-a_
-5-

10. Apply glue to the square tube on fuselage,insert the square
tube to the hole in front of rear
(Figure 9)
Rortr lttnolll0o /l
/t
\\." I I
/ 0,
Flnrl lltnolnui
_i.
,-\f
) l\
(
t, J
lh i' '
-?r
'\y" l/
,
\ Ja')'
\,'ll
\
Figure 9
11. Glue right side and left side wing to fuselage as fig shown below'
(Figure 10)
J
Figure 10
12.1. As flg shown, assemble rod fix to , (( ,
controlhorn. \E risht reor horn
12.2. Apply gule on horn end and put it through control surface'
14.1 Put front control to horn as fig shown'
14.2 Put rear control rod to horn as fig shown control rod assembly
13. Apply glue on horn batch and put it on horn end' press it tightly'
8\-:',==
t --::::::.
m
-a'<''6
-//7 t
-m

15'1 As shown in figure,the erevator ano contiot surface are in the
*. same level.
15.2 As shown in figure,aileron and wing fiailing edge are in the
same level
-9-