Hobby King H-KING Cri Cri User manual

WARNING:
Read this instruction manual fully so as to become completely familiar with the features of
this product before operating. Failure to operate this product correctly could result in
damage to the product, personal property and cause serious injury. This is a sophisticated
hobby product and is NOT a toy. It must always be operated with caution, common sense
and some basic mechanical ability. This manual provides instructions as the the assembly,
safe operation and m a in te n a n ce this hobby product. It is highly recommended that you
follow and read fully the instructions and warnings stated in this manual including safety,
assembly, setup and flying guidelines in order to operate this product correctly and avoid
damage or serious injury.
SAFETY PRECAUTIONS:
As the user of this product you and you alone are responsible for operating it in a manner
that does not endanger yourself and others around you or result in damage to the product or
property of others. This product is operated via a radio controlled system that in some cases
can be subject to interference from sources outside of your control. Interference may result
in a momentary loss of control so it is always recommended that this product be used in a
suitably open outdoors space.
- This is a radio controlled flying model and as such must always be flown with caution and
care. This is not a toy.
- The Cri Cri is designed for intermediate to advanced pilots.
- Always exercise great caution when using the recommended battery to power this product.
For full safety notes and operating procedures, please see information provided by your
battery supplier.
- Take great care when connecting/disconnecting the battery. See battery supplier for full
safety procedures.
- Never power up the model in confined spaces and always keep the props clear of
obstructions.
- This product is not a toy. Children must be accompanied by an adult at all times if operating
this product.
- Only fly this model in an open area away from crowds, people, buildings, tree’s, power lines
and obstructions.
- Always put safety first when operating this model and consider the warnings stated above.
- The supplier/manufacturer accepts no responsibility for damage or injury caused through
the use of the product. Not suitable for children under the age of 14. THIS IS NOT A TOY.

CONTENTS
*Specification.................................................................................... 1
*Spare parts listing............................................................................2
*Assembly...................................................................................... 3-9
*CG location....................................................................................10
*Trouble shooting.............................................................................11
*Model flying precautions ................................................................ 12
*Pre-flight checks.............................................................................13

SPECIFICATION:
Length :850mm
Flight weight: 1100g
Wingspan: 1150mm
Servos: 9G servos x4
Motor: Brushless Motor 2825 Outrunner KV1850
Battery: 11.1V-1300-1800mAh 20C LiPo Battery
ESC: 20Ax2

SPARE PARTS LISTING:
Fuselage Wing set Horizontal stab
Vertical stab Canopy hatch Cowls
Exhaust stacks Prop adaptor Propeller
Spinner Main gear Engine nacelles

ASSEMBLY:
1. Locate aileron control horns and push rods. Install the aileron control
horn using the screws and screw driver provided. Now connect the pushrod
to the aileron servo horn as shown. Repeat this step for the remaining wing
panel. Then using Y- lead connect the aileron servos.

2. Install the main landing gear using the screws and screw driver provided.
Then install the main to the fuselage as shown.

3. Locate the elevator control horns using the screws and screw driver
provided. Then install the elevator to the tail wing using the screws and
screw driver as shown. Now connect the pushrod to the elevator servo horn
as shown.

4. Pull forward into the fuselage as much of the rudder I-lead as possible.
Then with the tail plane turned over, apply glue to the entire portion of the
fuselage shown.
5. Fit and install the engine nacelle using the screws and screw driver fix
the engine nacelle on the fuselage front as shown.

6. Fit the props and spinners. Once you have established propeller
orientation, offer each prop up to the prop shafts and locate into position on
the spinner blue plate. Use the nut from the prop shaft to secure the prop in
place on the shaft. The spinner can now be screwed in place but be sure
to double check that each blade retaining bolt is secure and all blades are
at an equal distance from one another before you do.
7. Fit and install the exhaust. Apply glue to the stator to the fuselage using
the screws and screw driver install the exhaust as shown.