Hobby King MXS-R 64 User manual

Wing Span:64in/1625mm;Flying Weight:2700g;
Wing Area:50.1sq.dm;Radio:4Channel 6Servos;
Length:59 in/1500mm;Engine:20CC Gas
CAUTION CAUTION CAUTION CAUTION :::: this this this this plane plane plane plane is is is is not not not not aaaa toy toy toy toy and and and and should should should should be be be be kept kept kept kept away away away away
children children children children under under under under 16 16 16 16 years years years years of of of of age! age! age! age! Before Before Before Before use use use use , ,,, please please please please carefully carefully carefully carefully read read read read
this this this this manual. manual. manual. manual.
●First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce its
performance to full extent .
●Assemble this kit only in places out of children’s reach!
●Take enough safety percautions prior to operating this model.
You are responsible for this model’s assembly and safe operation!
●Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
P.1

MAIN MAIN MAIN MAIN WING WING WING WING
Apply epoxy into
hinge hole of the wing
Connect the aileron and
the main wing by hinges.
Be sure to apply instant
type glue to both sides
of each hinges.
Cut the servo holes on the
bottom of the main wings
P.2

Use glue to fix up the
horns
Install push-rod,used ruler
to measure the length
Put the servo into the
hole and fix it with screws.
P.3

Link the servo arms and
tri-horns with pushrod
Drill the holes
on the wing tips
Be assured that the screw
is fixed up
INSTALL WINGTIP WINGLET
P.4

You can also install wingtip
winglet,as shown.
STABILIZER STABILIZER STABILIZER STABILIZER AND AND AND AND ELEVATOR ELEVATOR ELEVATOR ELEVATOR
Cut the servo holes on the
profile of the fuselage
Fix up the stabilizer
of the fuselage
P.5

Apply epoxy into
hinge hole of the elevator
Fix up the stabilizer and
elevator with hinges and AB
glue.
Use glue to fix up elevator
horns
Install the servo in the hole
as shown
Be assured that the screw
is fixed up
P.6

Link the servo to
the elevator with pushrod.
RUDDER RUDDER RUDDER RUDDER
Apply epoxy into
hinge hole of the rudder
Use glue to fix up rudder
horns
P.7

Install the rudder servo
Be assured that the screw
is fixed up
attach the servo arm to the
ruddert servo as shown
As shown in picture, This is
finished for the rudder servo
P.8

MAIN MAIN MAIN MAIN LANDING LANDING LANDING LANDING GEAR GEAR GEAR GEAR
Fix up the landing gear
on the fuselage bottom with
screws.
●Bottom View
Put the cover board in the
right position,then fix up it.
Install the wheel as shown.
Install the wheel cover,
and fix it up to landing
gear with screw.
P.9

Install the tail landing gear
use screws to fix up the
fuselage bottom.
ENGINE ENGINE ENGINE ENGINE
Drill the engine mounting
holes as the board provided
Use the ruler to measure
the length from firewall
to airscrew
P.10

Put the cover board in the
hole,then fix up it.
Install the propeller and
spinner as shown
FUEL FUEL FUEL FUEL TANK TANK TANK TANK
Install the fuel tank into
the fuselage, and fix up it
with belt.
P.11

Install the fuel tank mounting
ties under the fuel tank floor.
Install the battery,receiver and
switch in place as shown.
CANOPY CANOPY CANOPY CANOPY AND AND AND AND COWL COWL COWL COWL
Install the canopy into
the fuselage as shown
P.12

Mount the cowl using the cowl
mounting screws.
CG CG CG CG POSITION POSITION POSITION POSITION & &&& CONTROL CONTROL CONTROL CONTROL THROWS THROWS THROWS THROWS
P.13

THE THE THE THE FINISHED FINISHED FINISHED FINISHED PHOTO PHOTO PHOTO PHOTO
THE THE THE THE FINISHED FINISHED FINISHED FINISHED PHOTO PHOTO PHOTO PHOTO
P.14