Hobby King WARGO YAK55 User manual

Instruction
Manual
Specifications are subjected to change without notice
due to product continuous improvements.

1

2
The Wargo Signature Yak 55 is the realization of my goal to have the perfect 3D and aero-
batic training aircraft. I have dedicated a lot of my ying career to teaching 3D aerobatics
and helping pilots learn how to become better pilots. I have also dedicated myself to trying
to develop the ideal transition and training 3D plane. Finally, we oer you the Wargo Yak
55. It is a perfect combination of value, performance and durability with no compromises
in aerobatic precision and the ability to perform every 3D aerobatic maneuver with authori-
ty. I wanted an economical and durable practice aircraft that can take a pilot from sport
ying to condently ying 3D aerobatics.
The result is a phenomenal plane that will hover, harrier and tumble incredibly well. Any
accomplished 3D pilot will love this plane because it will satisfy the most discriminating
pilot. It will perform maneuvers ultra-light foamies cannot because it has enough mass to
carry momentum and perform more high-energy and tumbling type of maneuvers.
The Yak 55 is also a perfect next step toward getting condent with larger balsa planes. It
is designed to perform like a balsa plane with the durability of a foamy. Best of all, most
mishaps can be repaired in seconds with a bit of glue, and you are ready to y again.
The Wargo Yak 55 a blast to y, and because it takes the fear of hitting the ground, it lets
you try aerobatics you cannot with your high-end balsa models. I hope you enjoy ying
your new plane as much as I enjoy it.
Happy Flying

1. Fuselage - 1pc
2. Wing with aileron (right and left) - 2 pcs
3. Rudder (vertical tail) - 1pc
4. Elevator (stabilizer) - 1pc
5. Landing gear plus wheels
6. Carbon rod wing spar - 1pc
7. Z-Bend 1.5mm* 200mm - 4pcs
8. Screw 3*10 - 4 pcs
9. Screw 2*3 - 4 pcs
10. Control horn - 4 pcs
11. Extension arm - 4 pcs
12. Pushrod connector - 4 pcs
13. Plywood servo mount - 4 pcs
14. Rubber band - 2 pcs
15. Fiberglass tail skid.
3
Parts included in the kit:
For Kit version:

Fuselage length:1080mm (42.15 in.)
Wingspan:1096mm (43.1 in.)
Flying Weight:690 – 760 grams (with battery)
Motor:Turnigy Aerodrive SK3 - 3530-1150kv
Brushless Outrunner Motor or HobbyKing
Donkey ST3007-1100kv Brushless Motor
ESC:Aerostar 30A Electronic Speed Controller
with 2A BEC (2~4S)
Propeller:10*4.7 SF or 11*4.7 SF
Servo:9-12 grams micro servo - 4 pcs
Radio:4 or more channels
Battery:11.1V 3S 1300 – 1800 mAh
Li-Po 25C
4
For PNF Version:
Product Specifications:

Fit the fiberglass servo extension arm onto the nylon
servo arm with screws provided
We will make the right wing first. Insert the aileron
servo and servo mount to the pre-cut servo slot.
Ensure those servo wires are properly organised
during the installation.
Apply CA glue to the servo mount.
5
1 2
3 4
5 6

Trim the excess pushrod wire with a wire cutter. Then
smooth the cut with a file.
Cut a slot on the aileron strip which is perpendicular to
the servo arm with a hobby knife as picture shown.
Glue the control horn as shown. Attach the “Z-bend”
pushrod to the control horn and lock it with the pushrod
connector.
Please repeat the above steps for the left wing.
Install the elevator servo with the servo mount as
shown.
6
7 8
9 10
11 12

Install rudder servo with servo mount on the rear part
of the fuselage as shown.
Cut a slot for the elevator control horn as shown .
Trail fit the elevator onto the fuselage. Ensure it is straight
and level to the fuselage and main wing. Then apply CA
glue to the joint between the elevator and fuselage.
Install “Z-bend” pushrod to the control horn and lock it
with the push rod connector. Then apply CA glue to the
control horn.
Tighten the grub screw and loctite it. Install the vertical stabiliser to the fuselage. Please
ensure that it’s perpendicular to the horizontal stabiliser.
7
13 14
15 16
17 18

Use the same technique as shown above to prepare the
control horn installation on the rudder.
Glue the rudder in place as shown.
Install “Z-bend” pushrod as shown and lock it with the
pushrod connector.
Apply CA glue to the rudder horn.
Insert carbon wing spar to one of the wing panel. Then
insert it to the wing mount on the fuselage and put the
other wing panel on and make sure it is well balanced
and true to the fuselage.
8
19 20
21 22
23 24

9
1. Connect the wings with two rubber bands as picture
shown. Yon can remove the wings during transportation
and for easy storage.
2. Apply slow curing epoxy to the wing root, wing spar
and permanent bond both wings and fuselage together
for ultimate flying performance.
Install the landing gear on the gear mount.
Install the brushless motor onto the motor mount and
secure it with 4 tapping screws provided with the kit.
Install the ESC onto the fuselage and secure it with a
zip tie.
Secure the battery flight pack to the fuselage with the
velcro band provided.
25 26
27 28
29 30
Glue the supplied fibreglass tail skid strengthener to
the fuselage as shown.
There are two ways to fix the wings onto the fuselage.
1. Connect the wings with two rubber bands as shown in
picture #25. You can remove the wings during transportation
and for easy storage.
2. Apply slow curing epoxy to the wing root, wing spar and
bond both wings and fuselage together permanently for
ultimate flying performance.