HOLLY&MARTIN Hagio HO976100TX User manual

HO976100TX
Hagio Desk
Assembly Instruction
Holly & Martin® a valued brand of SEI
Customer Service 1-800-633-5096
[email protected]
www.hollyandmartin.com

HO976100TX Hagio Desk
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Using a screw that is too long will
cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
diagrams below. You may receive e tra hardware with your unit.
A Quantity
Of 1pc
Wood Top
B Quantity
of 4pc
leg
C Quantity
of 2pc
Top rail
D Quantity
Of 2pc
Bottom rail
E Quantity
of 2pc
Connect panel
F Quantity
of 2pc
Apron
G Quantity
Of 1pc
Back panel
1 Quantity
Of 25pc
Long bolt:1/4”x2”
2 Quantity
Of 8pc
Short bolt:1/4”x7/8”
3 Quantity
Of 25pc
T-nut

4 Quantity
Of 8pc
Cam-lock
5 Quantity
Of 8pc
Cam Bolt
6 Quantity
Of pc
Wrench
7 Quantity
Of 14pc
Wood dowel
8 Quantity
Of 8pc
Screw:4mmx1-1/2”
9 Quantity
Of 37pc
PVC cover
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wa to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Please call manufacturer for assistance,
questions or parts.
Assembly Tool Required
No.2 Phillips Screwdriver

HO976100TX Hagio Desk
Assembly Instructions
F
FF
Figure 1
igure 1igure 1
igure 1
Unpack and lay parts on
clean, padded surface like
carpet or blanket. Check
that you have all parts
indicated on the front page
Insert cam locks (4) into
predrilled holes on top rail (C).
Screw cam bolt (5) into
pre-drilled holes on leg (B).
Attach top rail(C) to leg (B) by
inserting cam bolt (5) into
corresponding pre-drilled holes
until leg (B) &top rail (C) meet.
Tighten by rotating cam lock (4)
clockwise with Phillips
screwdriver.
Attach PVC cover (9) on the
cam-locks holes as shown.
F
FF
Figure 2
igure 2igure 2
igure 2
Insert T-nut (3) into predrilled
holes on leg (B)
Attach bottom rail (D) to
pre-assembled unit on figure 1
by inserting wood dowel (7) &
long bolt (1) into predrilled holes
until pre-assembled parts in
figure 1 & bottom rail (D)
meet.
Tighten withAllen wrench (6)
Then attach PVC cover (9)
on the T-nut holes as shown.
( 2)
( 1)
"Please do not over tighten cambolts. Please stop
when you feel tight"
B

F
FF
Figure
igure igure
igure 3
33
3
Attach connect panel (E) to
pre-assembled unit in figure 2.
Insert T-nut (3) into predrilled
holes on leg (B)
Attach connect panel (F) to
pre-assembled unit on figure 2
by inserting wood dowel (7) &
long bolt (1) into predrilled holes
until pre-assembled parts in
figure 2 & connect panel (F)
meet.
Tighten bolt (1) with Allen
wrench (6)
Attach PVC cover (9) on the
T-nut holes as shown.
1

F
FF
Figure
igureigure
igure 4
44
4
Repeat above steps to
attach the other leg frame.
Now two leg frames are
ready as shown
F
FF
Figure 5
igure 5igure 5
igure 5
Insert T-nut (3) into predrilled
holes on apron (F).
Attach apron (F) to
pre-assembled unit on figure 4
by inserting wood dowel (7) &
long bolt (1) into predrilled holes
until pre-assembled parts in
figure 4 & apron (F) meet.
Tighten withAllen wrench (6)
Attach PVC cover (9) on the
T-nut holes as shown.

F
FF
Figure
igure igure
igure 6
66
6
Attach pre-assembled unit on
figure 5 to wood top (A) using
short bolt (2) & screw (8).
Tighten bolt (2) with Allen
wrench (6) & tighten screw (8)
with Phillips screwdriver (not
included).
F
FF
Figure
igure igure
igure 7
77
7
Insert T-nut (3) into predrilled
holes on back panel(G)
Attach back panel (G) to
pre-assembled unit on figure 6
by inserting wood dowel (7) &
long bolt (1) into predrilled holes
until pre-assembled parts in
figure 6 & back panel (G) meet.
Tighten withAllen wrench (6)
Attach PVC cover (9) on the
T-nut holes as shown.
6

Now you Hagio Desk is ready
to use

Parts Replacement Form
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at [email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service
1-800-633-5096
[email protected]
www.hollyandmartin.com
600 Freeport Parkway, Suite 200
Coppell
, Texas
75019