HOLLY&MARTIN HZ640400TX User manual

PO#:
Page 1
HZ640400TX
Haza Shelf
Assembly Instructions
Holly & Martin® a valued brand of SEI
Customer Service 1-800-633-5096
[email protected]
www.hollyandmartin.com

1) Quantity
of 1
Top Panel
2) Quantity
of 1
Left Side Panel
3) Quantity
of 1
Right Side Panel
4) Quantity
of 2
Shelf Panel
5) Quantity
of 1
Middle Shelf Panel
6) Quantity
of 2
Middle Panel
7) Quantity
of 1
Bottom Panel
8) Quantity
of 2
Back Panel
A) Quantity
of 28
Cam Bolt
B) Quantity
of 28
Cam Lock
C) Quantity
of 28
Wood Dowel
Dia. 5/16” x1-1/4”
D ) Quantity
of
28
Screw Dia. 1/8” x 1/2”L
E) Quantity
of 2
Plastic Strap
F) Quantity
of 4
Bracket
G) Quantity
of 2
Screws Dia. 1/8”x1-1/2”L
Haza Shelf
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or a blanket. Check that you have all parts indicated. Call customer service if any hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage.
Page 2

H) Quantity
of 2
Anchor
I) Quantity
of 2
Screws Dia. 1/8”x5/8”L
J) Quantity
of 12
Adhesive Pad
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth. Avoid
rubbing or scratching the surface with rough or
abrasive objects.
For replacement parts or questions, please
call SEI Customer Service at 1-800-633-5096.
Assembly Tools Required:
No.2 Phillips Screwdriver, Hammer, Electric Drill
(Not Included)
Page 3

Page 4
Do not overtighten cam bolts. Stop when they feel secure.
Figure 1
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Middle Panel
(6).
Screw Cam Bolts (A) into threaded
holes on Shelf Panel (4).
Attach Shelf Panel (4) to Middle
Panel (6) by inserting Cam Bolts (A)
and Wood Dowels (C) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Cover Cam Locks (B) with Adhesive
Pads (J).
Figure 2
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Middle Panel
(6).
Screw Cam Bolts (A) into threaded
holes on Shelf Panels (4/5).
Attach Shelf Panels (4/5) to Middle
Panel (6) by inserting Cam Bolts (A)
and Wood Dowels (C) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Cover Cam Locks (B) with Adhesive
Pads (J).
Haza Shelf
Assembly Instructions
4
6
A
C
B
J
4
A
C
B
J
5

Page 5
Figure 3
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Shelf Panels
(4/5) & Bottom Panel (7).
Screw Cam Bolts (A) into threaded
holes on Side Panels (2/3).
Attach Side Panels (2/3) to Shelf
Panels (4/5) & Bottom Panel (7) by
inserting Cam Bolts (A) and Wood
Dowels (C) into corresponding holes
until all panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 4
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Side Panels
(2/3) & Middle Panel (6).
Screw Cam Bolts (A) into threaded
holes on Top Panel (1).
Attach Top Panel (1) to Side Panels
(2/3) & Middle Panel (6) by inserting
Cam Bolts (A) and Wood Dowels (C)
into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Cover Cam Locks (B) with Adhesive
Pads (J).
B
C
2
3
7
C
1
B
J

Page 6
Figure 5
Attach Back Panels (8) to back of the
unit with Screws (D).
Tighten Screws (D) with Phillips
screwdriver (not included).
Figure 5
Attach Brackets (F) to assembled unit
using Short Screws (I).
Tighten Screws (I) using a Philips
screwdriver (not included).
Mark two desired locations on wall.
Drill two 3/16" holes.
Insert plastic anchors (H) into the 2
holes, tap lightly with a hammer (no
included) as needed.
Attach the Brackets (F) to wall using
Long Screws (G).
Tighten Screws (G) using a Philips
Screwdriver (not included).
8
8
D
D

Page 7
Figure 6
Tie brackets (F) together with plastic
straps (E).
Warning: Anti-tip hardware must be
used for this product to avoid tipping
and injury.
Figure 7
Now your Haza Shelf is ready to use.

Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90
days of your receipt of the product. Replacement, if available, will be honored within this time frame.Parts will not be available for items
arriving fully assembled. We do not recommend modifying product(s) and we are not responsible for any damages due to product
modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or
replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas) Mon-Fri 9am – 4pm CST, or
email us at [email protected]. Please ask for customer service representative for issues involving damages or replacement parts.
Please ask for technical assistance representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Page 8
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
www.hollyandmartin.com
600 Freeport Parkway, Suite 200
Coppell, Texas 75019