HOLLY&MARTIN HZ778100TX User manual

HZ778100TX 2PC HANGZ
ANYWAY SHELF-BLACK
HZ778800TX 2PC HANGZ
ANYWAY SHELF - WHITE
Assembly Instruction
Holly & Martin® a valued brand of SEI
Customer Service 1-800-633-5096
[email protected]
www.hollyandmartin.com
PO#:12808

HZ7781
/HZ7788
2
PC
H
ANGZ ANYWAY SHELF
SET
Parts List
Please review all parts and hardware before disposing of any packaging.
Call CustomerService if missing hardware.
Using a screw that is too long will cause damage.Before beginning assembly, separate
each type of screw. Carefully studythe screw diagrams below.
You may receive extrahardware with your unit.
A
Quantity
Of 10
Small shelf
B
Quantity
Of 8
Large shelf
C
Quantity
Of 2
Back panel
1. Quantity
of 36
Bolt : Dia. 1/4”x1-/2”
2. Quantity
of 26
Wood Dowel
3.
Quantity
of 1
Allen wrench
4. Quantity
of 16
Screw 7mmx1-1/2”L
5.
Quantity
of 16
Plastic Anchor
6. Quantity
of 1
Level
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid ru ing or scratching the
surface with rough or a rasive o jects.
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096
Please call Manufacturer for assistance,
questions or Parts.
Tool List: 3/16" drill bit, drill, ta e measure and encil.
Assembly Tool Required No.2 Philli s
Screwdriver (Not Included)
Page 2

HZ7781/HZ7788 2PC HANGZ ANYWAY SHELF SET
Assembly Instructions
Figure 1
Note: These instructions detail how to
assemble one shelf. Repeat these
steps to assemble the other shelf.
Assembly Instructions:
Wood may scratch easily, Be careful
when assembling. Do not scratch.
Step 1
Unpack and lay parts on clean,
padded surface like carpet or blanket.
Check that you have all parts
indicated on the front page.
Step 2
Attached shelf (A) (B) to back panel
(C) with wood Dowel (3) as shown in
figure 1.
Figure 2
Step 3
Insert bolt (1) into back panel (C)’s
pre-drilled holes, tighten bolt (1) using
Allen wrench (3) as shown in figure 2.
Page3

NOTE: NO DRILLED HOLE OR PLASTIC ANCHOR
REQUIRED WHEN MOUNTING TO WOOD WALL.USE
SCREW ONLY. WE DO NOT SUPPLY HARDWARE FOR
MOUNTING ON CONCRETE WALLS.
Figure 3
Step 4:
Find a desired location. Mark 4
locations for screws on wall
One screw (for each unit) must be
attached directly into a wall stud. Wall
anchor is not needed when mounting
to wall stud.
Drill one of the marking 3/16" hole (for
each unit).
Insert plastic anchors (5) into the hole
on wall as shown. (When doing this,
you will need a hammer help you).
Using the Phillips head screwdriver,
install screw (4) into the anchor (5).
Turn the screw (4) until there is a gap
of approximately 3mm between the
head of the screw and the wall as
shown.
Figure
4
Step 5:
Hang the ANYWAY SHELF onto the
screw (4) and verify the ANYWAY
SHELF is resting securely on the
mounting screw (4).
Step 6
Place level (6) on top shelf to insure
product is level.
Now your ANYWAY SHELF is ready
to use.
If you prefer to hang this product in horizontal configuration, please follow below instructions.
(5)
(4)
Page 4

NOTE: NO DRILLED HOLE OR PLASTIC ANCHOR
REQUIRED WHEN MOUNTING TO WOOD WALL.USE
SCREW ONLY. WE DO NOT SUPPLY HARDWARE FOR
MOUNTING ON CONCRETE WALLS.
Figure 5
Step 7:
Find a desired location. Mark 4
locations for screws on wall
One screw (for each unit) must be
attached directly into a wall stud. Wall
anchor is not needed when mounting
to wall stud.
Drill one of the marking 3/16" hole (for
each unit).
Insert plastic anchors (5) into the hole
on wall as shown. (When doing this,
you will need a hammer help you).
Using the Phillips head screwdriver,
install screw (4) into the anchor (5).
Turn the screw (4) until there is a gap
of approximately 3mm between the
head of the screw and the wall as
shown.
Figure 6
Step 8:
Hang the ANYWAY SHELF onto the
screw (4) and verify the ANYWAY
SHELF is resting securely on the
mounting screw (4).
Step 9
Place level (6) on top shelf to insure
product is level.
Now your ANYWAY SHELF is ready
to use.
Each shelf su ort u to 9 lbs
Page 5
(5)
(4)

Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s).If damages
or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or
replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at serv[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Num er
Please indicate where you purchased this item: Store/We site/Catalog
Please indicate color/size/style num er:
Style No Parts Letter Parts Description Quantity Needed
Customer Service 1-800-633-5096
[e-mail]
www.hollyandmartin.com
600Freeport Parkway, Suite 200
Coppell, Texas 75019
Parts Replacement Form