Holman WXRL001 User manual

User Guide
12× Bulb 
Wi-Fi Festoon Kit
User Guide

2 of 22
PRODUCT CODE: WXRL001
iOS is a trademark of Apple Inc. Android is a trademark of Google LLC. The Android robot is reproduced
or modified from work created and shared by Google and used according to terms described in the
Creative Commons 3.0 Attribution License. All other content is Copyright©HolmanIndustries2022

3 of 22
Contents
Overview 4
Package Content 4
Setup 5
Preparation 5
Installing Holman Home 8
Bluetooth®Connection 9
Pairing 10
Key Functions 12
Bulb Control 12
Pallete (Scene) 14
Music 14
Timer 15
Troubleshooting 18
Specifications 20

4 of 22
Overview
Package Content
1. 12 light Festoon Lighting [a] String with PET diffusers, IP65
2. 1 × AC Adaptor [b], installed in a waterproof
outlet or under cover - not IP65
3. 1 × Inline Controller [c] (suitable for outdoor use)
4. 1.4m to first plug (after Inline Controller),
2.6m from DC adaptor to the first light
ÁNo modification or change to the light configuration is
possible and end cap must be secure
ba
c

5 of 22
Setup
Preparation
®Before connecting to power ensure the red O-Ring [a] is in place (for
electrical protection), and the screw cover is on [b]
ÁThe plug cannot be forced - if there is difficulty in
connecting, please review the plug for correct orientation
®Your power point (GPO) must be within 2.6m of the first light
®Plug in the light chain and using the Inline Controller, test all lights
are working
ab

6 of 22
Using the Inline Controller
®The Inline Controller may be located in an outdoor area if required.
®The Inline Controller has 3 buttons, allowing for pairing and also
manual use of the lights (outside of the app)
®Access to the Inline Controller should be considered as part of
set up
Setup (continued)
b. The top button is
manual power on/off
c. The middle button is
Wi-Fi pairing – press and
hold the button to enter
Wi-Fi pairing mode
d. The bottom button is a
manual mode selector
and this will move
through scenes and
colours with each press
ÁIf the festoon lights are not connected to Wi-Fi you must
allow a few minutes for the lights to exit pairing mode (turn
solid red) to be able to use the Inline Controller for testing
b
c
d
Preparation (continued)

7 of 22
Setup (continued)
Preparation (continued)
1. Unplug the lights
for installation
2. The 12 lights each have
a ‘keyhole’ [e] hang point
built into the top of the bulb,
please use this to secure
the lights to your structure.
Do not tie the main (black)
cable between the lights,
use the keyhole hang
point on each bulb only
3. If you plan to hang the
lights from a beam, every
6th light should be secured
(minimum 2 hang points)
4. When hanging on a guide
wire, each light should
have a hook or cable
secured to the guide
wire (12 hang points)
5. Bulbs must hang down
(as shown) for protection
from water ingress, do
not install bulbs with the
bulb facing up to the sky
6. Please consider the
hanging location and
avoid an area where the
bulbs may be subject to
repeating knocking against
walls or other items. This
will lead to breakage
7. The festoon string is not
intended for installation in
ceilings, eaves, cabinets,
or other enclosed spaces
ÁCable ties or S Hooks can be used for hanging– there is no
hardware included in this kit
e

8 of 22
Setup (continued)
Installing Holman Home
1. Download Holman Home
to your mobile device
via the App Store
or Google Play
2. Open Holman Home
on your mobile device
®You may be prompted to
allow notifications–the
app can still function if you
choose to opt out
3. Tap SIGN UP
4. Read our User Agreement
and Privacy Policy
and tap AGREE if you
wish to proceed
5. Follow the prompts to
register a Holman Home
account with your email
address
ÁEnsure your country
details are correct at this
stage
®You must allow the
‘Discovering Nearby Device’
permission (or Bluetooth
permission, depending
on your phone operating
system) – this allows
Bluetooth mesh products to
be added into Holman Home
®You may be prompted
to allow access to your
location. This allows the
app to show weather
information-it will still
function if you choose to
opt out

9 of 22
Bluetooth®Connection
LEnsure you and your
smartphone are close to
your light kit during the
connection process - you
may need to prompt pairing
mode.
LYour lighting kit will
perform preset schedules
from the app, even if
your smartphone is out of
Bluetooth® connection
range (schedules must be
sent within Bluetooth range)
Setup (continued)

10 of 22
Setup (continued)
Pairing
1. Pairing of the flood lights
is via Bluetooth mesh,
please ensure you have
allowed the Bluetooth
(iOS) or Nearby Devices
(Android) permission
2. These lights will flash red
to indicate they are ready to
pair (default/pairing mode)
3. Tap ‘Add Device’ from
the Holman Home Home
screen, you will see the
flood lights appear under
‘Discovering Devices’
4. If this is your first
Holman Home Wi-Fi device,
enter/review your Wi-Fi name
and password, then tap next
5. If this is not your first
device, your Wi-Fi name
and password will appear
pre-filled – review the
details and tap next

11 of 22
Pairing (continued)
Setup (continued)
a
b
6. On the ‘Add Device’ screen,
you can now see a blue
circle appear, please tap
this to commence pairing
7. The light will now be
added, allow 30 seconds
to 1 minute for this
8. The light is now added, tap
done to complete pairing
9. You will now be on
the settings page
10. Be default the light string
reports as 30 [a], please
adjust this to 12 lights [b]
and confirm to continue
ÁNo alteration or expansion
of the set is possible

12 of 22
Key Functions
Bulb Control
®Tipping Bucket – all lights
one colour. Tap the colour
on the selector to change
all lights
®Squiggle – change one light
at a time, tap the colour then
the light to change
®Eraser – remove a bulb
from the end of the current
display
Functions
®Menu options at the bottom
of the home screen - given
from left to right
a. Bulb Control -
Home, RGB/W mode,
colour selection
b. Pallete - Scenes
c. Music
d. Timer
a
b d
c

Bulb (continued)
Functions (continued)
®12 – number of bulbs in the
chain
®Mid screen – colour selector:
Tap paint brush or squares to
change the colour selector view
The brightness is adjusted via the
slider, by default this is 100%.
®Slide left to reduce
brightness.
®Tap ‘Colour’ or ‘White’ to
move between modes
®Down arrow – minimise the
selector screen. Tap the line
to restore the selector.
White selector example:

14 of 22
Pallete (Scene):
®Tap the scene to apply it to
the lights
Music:
®Requires audio recording
permission, as this uses the
device microphone to work
®Lights will change colour
(dance) to the beat
Functions (continued)

15 of 22
Timer:
®Tap the blue circle [a] to set
a schedule for daily use
®You will need one timer
for each schedule – this
includes a time for on, and
a time for off. As well as
allowing different times for
weekdays and weekends
Setting the Timer –
1. 24hr (military) time is used
for setting the schedule
2. For day of the week
selection blue squares
are ‘on’ (selected) [b],
while black squares are
‘off’ (not selected) [c]
Functions (continued)
b
a
c

16 of 22
Timer (continued)
Functions (continued)
3. By default the action
is ‘Turn off’
4. Tap action to choose how
the lights come on
5. Select colour or white, the
brightness and then save the
setting
Example of a complete
weekend timer

17 of 22
Timer (continued)
Functions (continued)
®It is possible to have a
different on and off for each
day of the week
®If a conflicting schedule is
created, the below message
will be shown:

18 of 22
The lights are plugged in for testing but they only flash red?
Leave the lights for a few minutes – they’ll exit pairing mode
after this time (turning solid red) and you can then use the mode
button on the Inline Controller to check they’re working
The lights won’t enter pairing mode (red flashing)?
Press and hold the Wi-Fi button on the Inline Controller for 5 seconds,
you may need to repeat this 2-3 times. If this does not work, turn the
power on and off (at the power point) 3 times – on/off/on/off/on/off/on
How can I remove my lights from Holman Home?
Tap the pencil at the top right
of any page when you’re
in the Festoon light menu.
You’ll now see a white page,
at the bottom in red there’s
‘remove device’ [a]
Troubleshooting
a

19 of 22
How can I remove my lights from Holman Home? (continued)
You’ll have the option to ‘Disconnect’, or ‘Disconnect and wipe’:
®Disconnect is a good idea for something like a modem change, or
moving house
®Disconnect and wipe will remove all settings from the lights (and
cloud) and restore factory defaults
Troubleshooting
The Holman website has a host of additional information on features. Head to
support.holmanindustries.com.au for more tips, tricks and support content.
If you still need help, feel free to email our friendly Customer Service team at
[email protected] or call at 08 9416 9999.

20 of 22
Specications
Festoon Kit
Input 230-240V AC
Output 12V DC
Light Output 0.5W per light
Pack Output 6W total
Size ø45mm
Height 130mm
Colour RGBW Multi
Waterproof Rating IP65
Housing Plastic