Home Decorators Collection ELSIE 60 GBSH162 User manual

PAGE 1
ELSIE 60
GBSH162 / GBSH171
INSTALLATION MANUAL
2023-07-26 HOMEDEPOT.COM/HOMEDEPOT.CA/HOMEDECORATORS
Questions, problems, missing parts?
Before returning to the store, call Home Decorators Collection customer service department at
1-800-986-3460, 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday.
An installation video guide can be found on our Youtube channel:
https://tinyurl.com/32657syz

PAGE 2
CAUTION
Please carefully read the following important safety information before handling or installing this shower. There is a
risk of serious injury while handling this product. To minimize these risks, please note:
• Always wear safety glasses and gloves while handling.
• Always read and follow all the steps in the installation instructions.
• Inspect all contents and glass for damage before installation.
• Keep the corner protectors on glass panels until the installation is nished.
• Extreme caution should be taken while handling the glass during installation as the tempered glass may shatter if
in contact with a hard surface.
• Handle the tempered glass with caution! Improperly handling the glass can cause it to break suddenly in small
pieces (never in pointed fragments).
• Always take all precautions not to touch the tempered glass with any tools during the installation, or after installed.
• Do not cut or modify the tempered glass as it will shatter if cut.
• Carefully remove product from packaging and keep packaging until installation is complete.
• Inspect all parts for damage; if there is damage to the unit prior to installation, please contact customer service at
the number provided in this guide.
• Install the shower on a oor that is level and able to accommodate the weight of the unit and an occupant.
• Consult local building codes and compliance standards prior to installation and ensure conformity.
• After installation, and from time to time, check the glass for t and nish to ensure that nothing has come loose
since installation.
• Keep this installation manual for future reference.
SAFETY INFORMATION
NOTICE
Any modication or alteration from what is specied in this instruction manual will void any and all warranty on this
product.
The distributor is not responsible for any damage to the unit or personal property caused by improper installation. If
you disregard instructional warnings, you will void your warranty and possibly deal with water damage.
Consult the distributor’s website for any additional information or question on this product’s installation.
SAFETY NOTICE
PREPARATION
You will need at least two people to install this unit properly.
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list
and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

PAGE 3
C
30 5/8 in
D
30 5/8 in
A
76 in
E
27 3/4 in
F
11 in
A
76 in
*B*
53 1/2 in~60 in
SHOWER DIMENSIONS
Measures: inch
Measurements
AShower height
*B* Shower width
CInner door panel width
DOuter door panel width
EDoor opening
FDistance between handle holes
*B*
ATTENTION!
This is the required shower space
measurement to install the shower.

PAGE 4
WALL-TO-WALL DIMENSIONS
WARNING!
**If you require to cut the bar, refer to the calculation below:
1. Measure the distance “D” at the height where the bar will be installed.
2. Cut the bar to a total length of L = D - 7/8 in.
3. The maximum measure to cut from the bar should be no more than 5 11/16 in.
L
L = D - 7/8 in
D
• Measure the thickness of your nished surface on either side before installing the metal tracks.
• Make sure to have a nished surface distance (D) between the min and max permissible dimensions according to the table
below.
*IMPORTANT: Your shower is designed to accommodate a 13/16 in tolerance from the maximum value. If needed you

76 in
FINISHED SURFACE OPENING (D) SHOWER DOOR HEIGHT
(Make sure the door height is not surpassing your tile /
acrylic wall height)
Support bar adjustability
MIN** MAX*
53 1/2 in 60 in 76 in

PAGE 5
PACKAGE CONTENT
B
x1
C
2x
D
1x
E
1x
F
2x
G
2x
H
1x
J
2x
K
2x
M
1x
N
2x
O
2x
P
1x
3 1/4 in
1 1/8 in
L
3x
I
2x
A
1x
Positioning tool
99SHW-ZV7QXQF5-WM
Inner door panel
99SGD-GP4M2DZ7-WM
Shower door stopper
Chrome: 99SDS-9FZNZZA8-WM
Brushed Nickel: 99SDS3668-WM
Support bar anchor
Chrome: 99SGC-8F00B5R1-WM
Brushed Nickel: 99SGC-4SZ18AW1-WM
Support bar
Chrome: 99SGS-9YQ46811-WM
Brushed Nickel: 99SGS-UH9Q0810-WM
Inner door roller
Chrome: 99SWE-X1LF3NI2-WM
Brushed Nickel: 99SWE3689-WM
Outer door roller
(with anti-jump hook)
Chrome: 99SWE-1J9X36JY-WM
Brushed Nickel: 99SWE-H72HRB53-WM
Outer door panel
99SGD-A015U10J-WM
Door handle
Chrome: 99SHA-R37B17OE-WM
Brushed Nickel: 99SHA-39580M95-WM
Door bottom seal strip
Transparent: 99SRU3904-WM
Glass panel vertical seal strip
Transparent: 99SRU3615-WM
Short seal strip
Transparent: 99SRU0265-WM
Sliding door guide
Chrome: 99SGC-VBN51CJ7-WM
Brushed Nickel: 99SGC4931-WM
Door panel vertical seal strip
Transparent: 99SRU3616-WM
Door’s seal track
Chrome: 99STR-S261C9XZ-WM
Brushed Nickel: 99STR-7AA9Q46V-WM
Decorative track
Chrome: 99STR1136-WM
Brushed Nickel: 99STR1137-WM
Complete hardware kit (refer to next page)
Chrome: 99SHW-FHB5AM3L-WM
Brushed Nickel: 99SHW-0454NFJC-WM

PAGE 6
SUPPLIED HARDWARE LIST
AA
Screw
ST4x20mm
2+1
Wall Anchor
ø8x40mm
4+1
Cap
4x
Screw
ST5x55mm
4+2
Allen key
2mm & 2.5mm & 4mm
Screw
ST4x30mm
2+1
BB CC
FFEE
Wall Anchor
ø6x30mm
2+1
DD
TOOLS REQUIRED (not supplied)
Pencil Screwdriver Drill and drill bits
ø1/8 in & ø1/4 in & ø5/16 in
LevelMeasuring Tape Silicone Rubber mallet
Cutter
Safety glasses Ratchet
3/16 in Bit socket
Glass suction cup

PAGE 7
DOOR ASSEMBLY OVERVIEW
C
D
AO
E
L
K
B
F
G
H
I
N
J
M
P

PAGE 8
BEFORE INSTALLATION
For the easy installation of this shower please read the following important points:
• READ ALL the instructions completely before beginning.
• Make sure your walls are within 3/8 in of plumb. And wall corners should meet at 90oas illustrated.
• Make sure your tub or shower base is level.
• When using Solid Polymer Composite (SPC) shower walls, dry t your shower door and make sure there is a stud where the
wall track will be installed.
Please see the images below for Alcove shower.
90o
90o
LEVEL
LEVEL
90o
LEVEL
LEVEL
90o

PAGE 9
A B
PREPARATION
This instruction is drawn up for a outter door opening from right to left (see illustration A).
For an installation for a outter door opening from left to right (see illustration B), use the
same instructions, but switch around the panels: mirror e󰀨ect.
FAQ
Q: If the shower head is installed
on the other wall, will it leak?
A: It is possible to install your
shower head on the other side,
but we strongly recommend to
install it as illustrated.
Install the shower head on the door’s side as shown in the illustration!
This will reduce the risk of leaking.
OUTTER
DOOR
OUTTER
DOOR
INNER
DOOR
INNER
DOOR
RIGHT
OUTTER DOOR
OPENING
LEFT
OUTTER DOOR
OPENING

PAGE 10
SUPPORT BAR INSTALLATION
1
1.1-1.2. Position the positioning tool (A) as illustrated. Level the positioning tool (A) and mark the positions of the holes on the
wall.
1.3. Remove the tool and drill pilot holes in the marked locations with a ø5/16 in drill bit.
1.4. If there are no studs located behind the support bar anchor (C), then insert the wall anchors (AA) using a rubber mallet until
the wall anchors are ush with the wall.
A
1 1/2 in
1.1
A
1.2
A
A
1.2
1.1
1 1/2 in
ø5/16 in AA
1.3 1.4
WARNING!
If there are no studs aligned to
the wall track behind the drywall,
use the wall anchors to ensure
the screws won’t become loose.
AA
A
A

PAGE 11
SUPPORT BAR INSTALLATION
2.1-2.2. Loosen the hex bolts from the support bar anchors (C) and then remove the cover from the support anchor (C).
2.3-2.4. Insert the wall anchors (AA) in the pilot holes using a rubber mallet. Fix the support bar anchors (C) on the wall using
the screws (BB).
2
C
C
WARNING!
If there are no studs aligned to support bar
anchors behind the drywall, use the wall
anchors to ensure the screws won’t become
loose.
C
C
2.2
2.3 2.4
AA
BB AA
BB
2.1
C
C

PAGE 12
D
1
L = D - 7/8 in
NEXT STEP MAY REQUIRE TO TRIM THE SUPPORT BAR
If the support bar is too long for your wall-to-panel opening “D”, you will have
to trim it down. Below calculation is for reference only: Ensure you made all
the proper measurements before you cut the bar.
1. Measure the distance “D” at the height where the bar will be installed.
2. Cut the bar to a total length of L = D - 7/8 in.
2
L

PAGE 13
SUPPORT BAR INSTALLATION
3.1-3.2. Place the support bar (E) into the 2 support bar anchors (C).
3.3-3.6 Slide the covers back onto the anchors (C) and x it using the hex bolts.
3
C
E
C
C
E
C
3.1 3.2
3.3 3.4
3.5 3.6
C
C
E

PAGE 14
SHOWER DOOR INSTALLATION
4.1. Measure the wall-to-wall distance "D1" in inches, calculate "D2" by subtracting 1 1/2 inches from "D1", then divide the result
by 2. This calculated measurement "D2" is the distance from the edge of the door guide (M) to the wall, as illustrated below. Mark
the positions of holes of the sliding door guide (M).
4.2. Drill pilot holes for the sliding door guide (M) using a ø1/8 in drill bit.
4
D
M
RIGHT OUTTER DOOR OPENING LEFT OUTTER DOOR OPENING
D= (D- 1 1/2 in) / 2
D
M
15/16 in
4.1 4.2
ø1/8 in
D
4.2
ø1/8 in
M
15/16 in
D
4.1
M
D
D

PAGE 15
SHOWER DOOR INSTALLATION
Note: The Inner door panel and the Outer door panel are not interchangeable. The distance from the roller’s hole to
the top edge of the panel is 3-1/4 in for the Inner panel (B), whereas it is 1-1/8 in for the Outer panel (H).
5.1. Install the 2 inner door rollers (F) on the inner door panel (B).
5.2-5.3. Insert the door bottom seal strip (J) onto the inner door panel (B).
5
B
J
F
B
Door roller’s hole Door roller’s hole
INNER DOOR PANEL OUTER DOOR PANEL
1 1/8 in
H
J
B
B
5.2
5.1 5.3
3 1/4 in
3/16 in
C
C
E

PAGE 16
SHOWER DOOR INSTALLATION
6.1-6.2. Gently hang the inner door panel (B) by its 2 rollers (F) on the support bar (E).
6.3-6.4. Smoothly slide the sliding door guide (M) at the bottom of the inner door panel (B), as illustrated.
6.5. Fix the sliding door guide (M) with the screws (CC).
6
F
B
EE F
B
M
M
6.1 6.2
6.3 6.5
CC
F
B
E
F
M
F
B
E
F
M
RIGHT OUTTER DOOR OPENING LEFT OUTTER DOOR OPENING
M
B
6.4

PAGE 17
B
D
SHOWER DOOR INSTALLATION
7
F
B
E
7.5
7.1 7.2
C
D
D
7.3
7.1-7.2. Insert the stopper (D) onto the inner door panel, ensure the stopper (D) is ush with the support bar anchor (C).
7.3. Mark the outline of the stopper (D) on the wall.
7.4-7.5. Completely remove the sliding door guide (M) and the inner door panel (B).
D D
RIGHT OUTTER DOOR OPENING LEFT OUTTER DOOR OPENING
M
7.4
CC

PAGE 18
8.1 8.2
SHOWER DOOR INSTALLATION
8
WARNING!
If there are no studs aligned to stopper
behind the drywall, use the wall anchors to
ensure the screws won’t become loose.
DD
8.4
ø1/4 in
8.3
8.5
DD
EE
E D
C
8.1. Completely remove the support bar (E).
8.2. Place the stopper (D) back on its wall mark, then mark its holes on the wall.
8.3-8.5. Drill a hole on the center marks with a ø1/4 in drill bit. If there are no studs located behind the stopper (D), then insert
the wall anchors (DD) using a rubber mallet until the wall anchors are ush with the wall. Fix the stopper (D) on the wall using
the screws (EE).
C
C

PAGE 19
SHOWER DOOR INSTALLATION
9
9.1-9.2. Reinstall the support bar (E) into the 2 support bar anchors (C).
9.3. Gently hang the inner door panel (B) by its 2 rollers (F) on the support bar (E).
9.4. Smoothly slide the sliding door guide (M) at the bottom of the inner door panel (B).
9.5. Fix the sliding door guide (M) with the screws (CC).
F
B
E
9.3
C
C
9.1 9.2
B
M
M
HELPFUL HINT!
Add a drop of silicone
in the holes before
inserting the screws.
9.4 9.5
CC
F
B
E
F
M
F
B
E
F
M
RIGHT OUTTER DOOR OPENING LEFT OUTTER DOOR OPENING

PAGE 20
BB
N
N
10.1 10.2
3/16 in
D
SHOWER DOOR INSTALLATION
10.1-10.2. Install the door vertical seal strip (N) on the closing end of the inner door (B), cut the surplus at the top of the strip (N),
as illustrated.
10.3. Install the glass panel vertical seal strip (K & L) onto the inner door panel (B).
10
BL
K
10.3
B B
L L
K K
RIGHT OUTTER DOOR OPENING LEFT OUTTER DOOR OPENING
N N
D D