Home Decorators Collection BELFORD User manual

Item #XXX XXX
Model #SW1732/
DAMP ORB
BELFORD LED 52 INCH CEILING FAN FOR DAMP LOCATION

Installing the Light Kit ...............................................7
Attaching the Fan Blade............................................10
Hanging the Fan.........................................................11
15
15
16
16
16
17
18
To reduce the risk of fire or electric shock, this
fan should only be used with fan speed control part
NO.:DL-1170FCS-03, manufactured by: Summer Wind
International. ,Ltd.
2
2
3
4
3
3
3
5
6
7
□Read and save these instructions.
□To reduce the risk of electric shock, ensure electricity has
been turned off at the circuit breaker or fuse box before
beginning.
□All wiring must be in accordance with the National Electrical
Code “ANSI/NFPA 70-1999” and local electrical codes.
Electrical installation should be performed by a qualified
licensed electrician.
□The outlet box and support structure must be securely
mounted and capable of reliably supporting a minimum of 35
lbs. Use only UL Listed outlet boxes marked “FOR FAN
SUPPORT.”
□The fan must be mounted with a minimum of 7 ft. clearance
from the trailing edge of the blades to the floor.
□To avoid personal injury or damage to the fan and other
items, be cautious when working around or cleaning the fan.
□Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
□After making electrical connections, spliced conductors
should be turned upward and pushed carefully up into the
outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on
the other side of the outlet box.
□All setscrews must be checked and retightened where
necessary before installation.
□This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must
accept any interference received, including interference that
may cause undesired operation.
WARNING: To reduce the risk of personal injury, do not
bend the blade arms (also referred to as flanges), when
installing the brackets, balancing the blades, or cleaning the
fan.
WARNING: Do not insert foreign objects between rotating
fan blades.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
WARNING: To reduce the risk of fire, electric shock, or
personal injury, mount the fan to the outlet box marked
acceptable for fan support with the screws provided with the
outlet box.
CAUTION: To reduce the risk of personal injury, use only
the screws provided with the outlet box.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.

120 2.66’ ft.
0.04
0.05
0.09
0.17
0.32
0.47
8.32 kg 9.7 kg
(18.3 lbs) (21.34 lbs)
2.2
3.17
5.61
10.46
21.56
33.53
50
70
96
120
156
177
1172
1880
2672
3548
4544
5063
1
2
3
4
5
6
Fan size WattsRPM CFMSpeed VoltsAmpsN.W. G.W. C.F.

16
16
9
Mounting screw (preassembled)
Mounting screw
Blade bracket screw
Glass cover screw
NN
7
11
4
NN
Wire nuts (not to scale)

Glass
Decorative scroll
6 W LED Bulb
Glass Cover
Blade bracket
5
Blade
Mounting bracket
Canopy
Canopy Cover
Hanging Ball (preassembled)
Downrod (preassembled)
Couping Cover
Fan motor assembly
Light kit Plate
Light kit
I
J
P
Q
R
S
1
4
2
1
5
1
1
1
1
P
Q
R
S

Remove one of the three screws (LL) from the fan motor
assembly (H) mounting ring and loosen, but do not remove,
the other two screws (LL).
Place the key holes from the light kit plate (I) over the two
screws (LL) previously loosened from the fan motor
assembly (H) mounting ring. Turn the light kit plate (I) until it
locks in place at the narrow section of the key holes. Secure
by tightening the two screws (LL) previously loosened and
the one screw (LL) previously removed.
Installing the light kit plate
Align holes in the light kit (J) and the light kit plate (I),
and secure with the mounting screws (LL) .
Ensure all the three mounting screws (LL) are tightened.
Installing the light kit
H
I
LL
H
I
I
J
LL
J
Installing the Light Kit
Installing the Light Kit (continued)

Put the light kit assembly down into the glass (K) .
Align holes in glass (K) and the light kit plate (I) and the
decorative scroll (L) , secure them together with the
mounting screw (LL) .
Follow the same process for all four decorative scrolls (L) .
Ensure all the four mounting screws (LL) are tightened.
Installing the decorative scrolls
H
J
K
H
L
K
LL
H
K
I
I
I
Installing the Light Kit (continued)

Install the two 6 watt LED standard E26 base bulbs (M)
into the sockets.
Installing the bulbs
Align holes in the decorative scroll (L) and the glass
cover (N), and secure with the glass cover screws (NN).
Ensure all the four glass cover screws (NN) are
tightened.
Installing the glass cover
M
K
M
N
L
N
L
NN
NN
Installing the Light Kit (continued)

Attaching the Fan Blade
Attach the fan blades (A) to the blade bracket (O) by
using three blade screws (AA) and fiber washer (BB).
Tighten the blade screws (AA) and the fiber washer (BB)
securely.
Fastening the blade to the blade
bracket
Tighten the blade assemblies on the fan motor
assembly (H) by using the blade bracket screws (MM) .
Fastening the blade assemblies to
the fan motor assembly
A
O
A
K
AA
BB
MM