Home Decorators Collection 1006185190 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b)Thisproduct is for indoor use only. The electrical rating0.25 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
i)Thisisanelectricproduct–notatoy! Toavoidriskoffire,burnspersonal
injuryandelectricshockit shouldnot be playedwithor placedwheresmall
children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m)Do not cover the product with cloth, paperor any materialnotpart of the
product when in use.
n) Do not move the tree by pulling the tree tips or tree branches.
o) Read and follow all instructions that are on the product or provided with
the product.
p) SAVE THESE INSTRUCTIONS.
CAUTION! – ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
Use and Care Instructions
a) Before using or reusing, inspect product carefully. Discard any
productsthathavecut,damaged,orfrayedwire insulationorcords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
b) When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to avoid
any undue strain or stress on the product conductors, connections,
and wires.
c) When not in use, store neatly in a cool, dry location protected from
sunlight.
9ft Snowfall Shimmer Noble Fir LED Tree
SKU# 1006185190
Package Contents
A. Top Section
Qty: 1
B. UpperMiddle
Section
Qty:1
C. LowerMiddle
Section
Qty:1

D. Tree Bottom
Qty: 1 E. Standwithan eyebolt
Qty:1
F. Powercord
Qty:1
G. Latch
Qty: 2
H. Threadediron
latch
Qty: 2
I. Retainer
washer
Qty:4
J. Replacement
bulb
Qty:8




Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2. Open the stand to a 90 degree angle until the hole lines up with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
Pre-Assembly

Assembling the tree
Pleaseremove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (D) into the tree stand and tighten the screw.
(See Fig. 1)
Step2.Insertlowermiddlesection (C)intothetreebottom(D).(SeeFig.2)
Step 3. Insert upper middle section (B) into the lower middle section (C).
(See Fig. 3)
Step 4. Insert tree top (A) into the upper middle section (B). (See Fig. 4)
Step 5. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 5)
Step 6. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and oneat the center of the main
stem. Repeat pattern for each branch. (See Fig. 6)
Step 7. Plug the power cord into a proper outlet. Please note this tree
comes with a foot pedal switch for easy illumination.
User Servicing Instructions
Replace the lamp.
1. Grasp plug and remove from its power source.
2. Unlock the lock on the bulb socket.
3. Pull bulb AND plastic base straight out of socket. Do not twist bulbs
while you are removing them.
4. Replace burned-out bulb with 3 V, 20 mA LED bulb ONLY.
(Additional bulbs are included for your convenience.)
5. Relock the lock on the bulb socket.
If the new bulb base does not fit in bulb holder, follow these steps:
 Remove the cover.
 Removethebaseof theburned-outbulb
by straightening the bulb leads, and
gently pull bulb out.
 Thread leads of new bulb through holes
in old base with one lead in each hole (always match the long lead of
new lamp to the hook of lamp base).
 After bulb is fully inserted into base, bend each lead up so that the
leads will touch the contacts inside the bulb holder.
 Insert the cover.
CAUTION:
1. To reduce the risk of overheating, replace burned-out lamps promptly.
Use 3.0 Volt, 20 mA LED lamps only.
2. Riskoffire.Thisproductdoes not contain lampshunts,whichallowthe
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
3. This product can only be used with the original adapter, not other
brands of adapter.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (D) and save them.
Step 3. Gently lift the tree top straight up to remove from the center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step5. Carefullyplacealltreesectionsintoashippingboxandtapeitshut.
Step 6. Store your tree neatly in a cool, dry place away from sunlight.
CAUTION! – ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ATTEMPTING BULB REPLACEMENT.
Troubleshooting
Problem Solution
The tree
doesnotlight
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Make sure the power cord is well connected to the
wall outlet.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Loose branches
1. If a branch of the tree in section A, B or C falls off, follow the steps
below to reinstall it with a spare latch (G).
1) Place the branch into the slot of the bracket.
2) Insert a spare latch
through the hole and
use diagonal pliers (not
included) to crimp the
latch. (See Fig. A)
2. If a branch of the tree in section D falls off, follow the steps
below to reinstall it with a spare threaded iron latch (H) and two
retainer washers (I).
1) Place the branch into the slot of the bracket.
2) Insert a spare threaded
iron latch (H) through the
hole and secure using two
retainer washers (I). (See
Fig. B)

The device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Warning: Please note that changes or modifications not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
Importer: Home Depot
Address: 2455 PACES FERRY ROAD ATLANTA, GA 30339
Tel: [phone]
Adapter Model No. TS-12W12V