Home Skinovations Silk'n Reju User manual

1
Instructions
for Use

2
The skin should be, clean, dry and free of any powder, gel or cream.
Remove Silk’n Reju APPLICATOR from its cradle in the BASE UNIT.
Press the POWER ON/OFF SWITCH.The green READY/TREATMENT MODE
1 - INDICATOR LIGHT (I) will start blinking, and shortly afterwards will be
lit steadily.
Your Reju is ready for treatment.
Place the TREATMENT SURFACE on your skin.The LED light will
automatically activate.
Apply light pressure while slowly moving the Reju APPLICATOR in small
circular motions.The TREATMENT SURFACE temperature will slowly
increase.
Perform the treatment for 5-7 minutes on each area.
It is recommended to apply a small amount of a moisturizing cream
on the treated skin areas after each session and to massage it gently in
circular motions.
Treating with
Silk’n Reju
for the First Time

1
Table of Contents
Before You Start.......................................................................................................................................2
What is Silk’n Reju?........................................................................................................................................2
Silk’n Reju device description.................................................................................................................2
Package contents.............................................................................................................................................3
Safety with Silk’n Reju........................................................................................................................3
When to avoid using Silk’n Reju?...........................................................................................................3
Reducing the risk of injury..........................................................................................................................4
Possible side effects using Reju................................................................................................................4
Protect your Silk’n Reju................................................................................................................................4
Skin Treatment the Reju Way....................................................................................................5
The benefits of Silk’n Reju..........................................................................................................................5
Silk’n Reju facial treatment areas.............................................................................................................5
Plan your Silk’n Reju treatment for best results
First Steps with Silk’n Reju............................................................................................................5
Silk’n Reju setup...............................................................................................................................................5
Silk’n Reju battery charging........................................................................................................................5
Treating with Silk’n Reju for the first time...................................................................................6
What to expect when treating with Silk’n Reju?...........................................................................7
After treating with Silk’n Reju...................................................................................................................7
Maintenance of Silk’n Reju........................................................................................................8
Cleaning Silk’n Reju......................................................................................................................................8
Storage..............................................................................................................................................8
To protect the environment.....................................................................................................................8
Removing the rechargeable batteries...................................................................................................8
Troubleshooting...........................................................................................................................9
Customer Service.................................................................................................................................10
Specifications............................................................................................................................................11
Labeling..........................................................................................................................................................12

2
Before You Start
Before using Silk’n Reju for the first time, please read this Manual in its entirety. Pay particular
attention to sections on device use procedures, device operation, and after-use procedures.
What is Silk’n Reju?
Silk’n Reju is an FDA cleared hand held light emitting diode (LED) device for facial treatments
of periorbital wrinkles, reducing pore size and temporary improvement of the appearance
of the skin. The light emitted by Silk’n Reju stimulates deep skin tissue and achieves facial
rejuvenation.
Typical areas for Silk’n Reju treatment are the neck, the cheeks, the forehead, and around
the eyes.
Silk’n Reju device description
Silk’n Reju device consists of a BASE UNIT,an APPLICATOR and an ADAPTOR.
Silk’n Reju APPLICATOR is a hand held unit that contains TREATMENT SURFACE at the APPLICATOR tip,
ON/OFF SWITCH and INDICATOR PANEL.
Silk’n Reju BASE UNIT is used to charge the APPLICATOR batteries.
F
G
A
B
C
D
E
H
L
K
J
I

3
PlugGTreatment surfaceA
BASE UNIT socketHOn/Off SwitchB
Ready/Treatment – ON/OFF Green indicator lightIIndicator PanelC
System Error - Yellow indicator lightJ
APPLICATOR
D
Battery charging - Orange indicator lightK
BASE UNIT
E
Battery full – Green indicator lightLAdaptorF
Package contents
Upon opening the Silk’n Reju package, you will find the following:
Reju BASE UNIT and APPLICATOR
Adaptor
Post treatment cream
User manual
Safety with Silk’n Reju
To protect your skin, a temperature sensor is embedded in the treatment tip of the Silk’n Reju. This
sensor ensures the skin’s surface will not exceed 41°C / 106°F.
When to avoid using Silk’n Reju?
Certain conditions may temporarily prevent the use of Silk’n Reju. DO NOT USE Silk’n Reju if any
of the following conditions apply to you:
If you have dark brown or black spots, such as large freckles, birth marks, moles or warts on
the area to be treated.
If you have eczema, psoriasis, lesions, open wounds or active infections, such as cold sores in
the area to be treated.Wait for the effected area to heal before using Silk’n Reju.
If you have abnormal skin conditions caused by diabetes or other systemic or metabolic diseases.
If you are currently or have recently been treated with Alpha-Hydroxi Acids (AHAs),
Beta-Hydroxi Acids (BHAs), Retin-A®, topical retinoids or azelaic acid.
If you have been treated with Accutane® (isotretinoin) within the past 6 months.
If you have been on a steroid regimen within the past 3 months.
If you have a history of herpes outbreaks in the area of treatment, unless you have consulted
your physician and received preventative before using Silk’n Reju

4
Reducing the risk of injury
• Keep Silk’n Reju out of the reach of children.
• Keep Silk’n Reju out of the reach of persons with reduced physical, sensory or mental capabilities.
• Keep Silk’n Reju away from water!
Do not use or store Silk’n Reju in a wet environment (e.g. near a shower or a bathtub)!
Keep the device and its adaptor dry!
• Do not use Silk’n Reju if the ADAPTOR or the APPLICATOR is damaged!
• If the APPLICATOR is damaged, make sure it is replaced with an original part from Home Skinovations!
• The APPLICATOR contains a dedicated transformer. Never replace the APPLICATOR with another plug!
If you are unsure if Reju is safe for you to use, please consult with your doctor or dermatologist.
Possible side effects using Reju
When used according to the instructions, side effects and complications associated with use of
Silk’n Reju are rare. However every cosmetic procedure, including those designed for home use,
involve some degree of risk. Therefore it is important that you understand and accept the risks
and complications that can occur with energy based systems designed for home use.
Silk’n Reju treatments are generally very well-tolerated. Most users sense the moderate heat
applied by the device during use, with no further discomfort.
• Minor Skin Discomfort
Your skin may become slightly irritated after using Silk’n Reju.This is a typical and transient
phenomenon. If the irritation does not disappear within three days,
please consult a physician or a dermatologist.
• Skin Redness
Your skin may become slightly red right after using Reju.This should disappear a few hours
after treatment.
Following the treatment it is recommended to apply a small quantity of the Silk’n Reju Cream.
Protect your Silk’n Reju
• Store the device in a clean area free of dust.
• Do not cover the ventilation slots during use.
• Never shake or drop Silk’n Reju or subject it to severe shocks.
• Silk’n Reju is sensitive to environmental temperature during use.
Do not expose the Reju to environmental temperatures lower than 15°C / 59°F or higher than
35°C / 95°F during use.
• Silk’n Reju can not tolerate extreme change of temperature.
When moved from a cold environment (under 10°C / 50°F) to a warm environment, avoid use
for approximately 3 hours.
• Do not expose Silk’n Reju to direct sunlight or UV light for long periods of time.
• Silk’n Reju is designed for occasional home use (as opposed to exhaustive commercial or
professional use). Avoid such exhaustive use.
• Avoid covering Silk’n Reju and its adaptor during recharge.

5
Skin Treatment the Reju Way
The benefits of Silk’n Reju
The outcome of using Silk’n Reju when following instructions correctly will be the reduction of
facial fine lines, reducing pore size and improving the appearance of the face.
Best results can be expected 3-7 weeks after completing the recommended course of treatment.
Silk’n Reju facial treatment areas
Typical areas for Silk’n Reju treatment are the cheeks, forehead, neck, and around the eyes.
First Steps with Silk’n Reju
Silk’n Reju Setup
1. Remove Silk’n Reju BASE UNIT, APPLICATOR, ADAPTOR and other components from box.
2. Before using the Silk’n Reju for the first time, fully charge the battery.This may take up to 6 hours.
Silk’n Reju Battery Charging
Insert the APPLICATOR into its cradle in the Reju BASE UNIT.
Plug the ADAPTOR PLUG into the Base Unit socket.
Plug the ADAPTOR into an electrical outlet. An orange BATTERY – CHARGING - INDICATOR LIGHT (K)
will illuminate to indicate that your Silk’n Reju is in the process of charging.
Caution!
Never cover Silk’n Reju and its
adaptor while recharging!
Note!
Silk’n Reju can not be used
while recharging

6
When BATTERY – CHARGING - INDICATOR LIGHT (K) turns off and BATTERY – FULL - INDICATOR LIGHT (L)
illuminates, your Silk’n Reju is fully charged and ready to start.
(Recharging will be needed when BATTERY – CHARGING - INDICATOR LIGHT (K) illuminates again.)
Plan your Silk’n Reju treatment for best results
The efficiency of the results varies from person to person and according to the frequency of
use. Some may see results sooner than others.
A single Reju session usually takes 15-20 minutes in which you should gently glide the Reju
applicator slowly over the desired treatment area. During the procedure you should feel gentle
heat penetrating deep into the skin.
Initial Silk’n Reju treatment course: For the first month (4 weeks), treatment should be
performed 3 times a week for 15-20 minutes each time.
Silk’n Reju maintenance regime:
Use Silk’n Reju once a week for 15-20 minutes.
Treating with Silk’n Reju for the FirstTime
The skin should be, clean, dry and free of any powder, gel or cream.
Remove Silk’n Reju APPLICATOR from its cradle in the BASE UNIT.
Press the POWER ON/OFF SWITCH. The green READY/TREATMENT MODE 1 - INDICATOR LIGHT (I) will
start blinking, and shortly afterwards will be lit steadily.
Your Reju is ready for treatment.
Place the TREATMENT SURFACE on your skin.The LED light will automatically activate.
Apply light pressure while slowly moving the Reju APPLICATOR in small circular motions. The
TREATMENT SURFACE temperature will slowly increase.
Perform the treatment for
5-7 minutes on each area.
It is recommended to
apply a small amount of a
moisturizing cream on the
treated skin areas after each
session and to massage it
gently in circular motions.

7
What to expect when treating with Silk’n Reju?
During a Silk’n Reju session it is normal to experience and feel:
A Sensation of Warmth – During the Silk’n Reju session you may feel slight warmth.This is
normal and should disappear up to an hour after the session.
Some Mild Red Color – After each Silk’n Reju session you may notice a slight reddening
of the skin (mild erythema) over the treated area.This is normal and should fade within an
hour or two.
Best results can be expected 3-7 weeks after completing the recommended course of treatment.
After treating with Silk’n Reju
When Reju session has been completed turn Reju off by pressing the POWER ON/OFF SWITCH.
After each session it is recommended that you clean your Reju device, especially the APPLICATOR
TIP (See Section:“Cleaning Reju”).
Place the APPLICATOR in its BASE UNIT cradle to recharge the batteries (See Section:“Silk’n Reju
Battery Charging”).

8
Maintenance of Silk’n Reju
Cleaning the Silk’n Reju
After each session, it is recommended to clean your Silk’n Reju device:
• Turn Silk’n Reju off by pressing the POWER ON/OFF SWITCH.
• Unplug Silk’n Reju from the electrical outlet
• Allow cooling down of its TREATMENT SURFACE.
• Use a dry, clean cloth and a specially formulated cleaner for electronic equipment
togently wipe the device and especially its TREATMENT SURFACE.
Never immerse Silk’n Reju or any of its parts in water!
• Never clean the Reju or any of its parts under the tap or in the dishwasher.
Storage
• Store the clean device and all its parts in a dry place, at a temperature of between -10°C to
60°C / 14°F to 140°F
To protect the environment
At the end of its life, do not discard Silk’n Reju with the normal household waste. Dispose
of it at an official recycling collection point.
Remove batteries and dispose at an official collection point for batteries. Please call your
local recycling depot for locations and proper recycling instructions.
Removing the rechargeable batteries
Remove the rechargeable batteries only if they are completely empty and cannot be recharged.
Undo the screw at the bottom panel of the APPLICATOR.
Lift and remove the top panel of the APPLICATOR.
Cut the tow wires that connect the electronics card to
the lower panel of the APPLICATOR.
Push the three snaps and pull out the electronics card.
Cut the tow wires that connect the rechargeable batteries
pack to the APPLICATOR.

9
Troubleshooting
This chapter summarizes the most common problems you could encounter. If you are unable to
solve the problem with the information below, contact your local Silk’n Customer Service Center
for further support.
SolutionPossible CauseProblem
Charge the APPLICATOR
The rechargeable
batteries are empty
Silk’n Reju does not
work
Contact your local Silk’n customer Service
center
The APPLICATOR is
broken
Charge the APPLICATOR The rechargeable
batteries are empty
Silk’n Reju suddenly
switches off
No action is required This is normal Device temperature
rises during recharge
Insert the PLUG into the BASE UNIT SOCKET The ADAPTOR is
not plugged in the
electrical outlet
BATTERY – CHARGING -
INDICATOR LIGHT (K)
does not turn on
when connecting the
PLUG into the BASE
UNIT SOCKET
Connect another appliance to the wall
socket to check if the electrical outlet is live
If the APPLICATOR still does not charge,
contact your local Silk’n Customer Service
Center
Make sure the APPLICATOR is inserted
properly into the electrical outlet and/
or PLUG is inserted properly into the BASE
UNIT SOCKET
The ADAPTOR is not
inserted properly
into the electrical
outlet and/or the
PLUG is not inserted
properly into the
BASE UNIT SOCKET
Contact your local Silk’n Customer Service
Center
The APPLICATOR is
broken
No action is required This is normal
APPLICATOR
temperature rises
during use
Press the ON/OFF SWITCH twice to switch
the Applicator off and on again. If READY/
TREATMENT MODE - INDICATOR LIGHT (I) does
not illuminate again, contact your local Silk’n
Customer Service Center
The APPLICATOR
needs to be reset
READY/TREATMENT
MODE - INDICATOR
LIGHT (I) does not
illuminate when
pressing the ON/OFF
SWITCH

10
Customer Service
For USA and Canada customers:
For more information about Silk’n™ products please visit www.silkn.com.
If your device is broken, damaged, in need of repair, or for any other user assistance, please
contact Silk’n™ Customer Service: 1-877-DO-SILKN / 1-877-367-4556, [email protected]
International Customers:
For more information about Silk’n products or to find a list of International Silk’n websites please
visit www.silkn.eu or www.silkn.com.
If your device is broken, damaged, in need of repair, or for any other user assistance, please
contact your local Silk’n™ Customer Service or write to: [email protected].
Manufacturer:
Home Skinovations Ltd.
Apolo Building, Shaar Yokneam POB 533
Yokneam 20692
ISRAEL
Press the ON/OFF SWITCH twice to switch the
Applicator off and on again. If SYSTEM ERROR -
INDICATOR LIGHT (J) illuminates again, contact
your local Silk’n customer Service center
Malfunction of the
APPLICATOR
The Yellow SYSTEM
ERROR - INDICATOR
LIGHT (J) is lit.
Charge the ADAPTOR The rechargeable
batteries are empty
The Yellow SYSTEM
ERROR - INDICATOR
LIGHT (J) is blinking
Disconnect the ADAPTOR from the electrical
outlet, press the ON/OFF SWITCH twice to
switch the APPLICATOR on and off again.
Connect the Adaptor to the wall socket,
If the problem persists, contact your local
Silk’n Customer Service Center
Malfunction of the
ADAPTOR
The Orange BATTERY
– CHARGING and
Green BATTERY – FULL
- INDICATOR LIGHTS
are illuminated
alternately
Press the ON/OFF SWITCH twice to switch the
Applicator off and on again. If the problem
persists, contact your local Silk’n Customer
Service Center
Malfunction of the
APPLICATOR

11
Rated voltage (Adaptor) 100V - 240V
Model: UE08WCP-105040SPA
Rated frequency (Adaptor) 50Hz – 60Hz
Rated currant (Adaptor) 400 mA
Applied part Type BF
Protecting rating IP20 (EN60529)
Storage condition Temperature: -10°C to 60°C / 14°F to 140°F
Relative humidity: 5% to 95%
Operating condition Temperature: 15°C to 35°C / 59°F to 95°F
Relative humidity: 10% to 80%
Atmospheric pressure: 700 to 1060 hPa
Light source Light Emitting Diodes
Wavelengths peak emission wavelength: 645nm
Intensity power: 250mW ±35%
Lithium ion battery 2 x 3.7V, 750±50mAh
Max. charging time 180 minutes
Specifications

12
Labeling
Degree of protection against electric shock: type BF applied part
WEEE - Waste Electrical and Electronic Equipment
CSA Mark
CE Mark
Degree of protection against ingress water: ordinary
This device is not suitable for use in the presence of flammable anesthetic mixture with air or with Oxygen or
Nitrous Oxide.
The symbol on the label affixed to this device means “Attention, consult accompanying documents”.

13
Apolo Building,ShaarYokneam POB 533,Yokneam 20692,ISRAEL www.silkn.com
tel. [phone], fax [phone], [email protected], [email protected]
Manufacturer: Home Skinovations Ltd. 4 Hacharoshet St., Kfar Saba P.O.B. 7028, Israel,
44640,Tel: [phone] | Fax: [phone]
Authorized Representative: Duotec Medical GmbH. Dr. Kurt Huber Str. 6, D-82031
Grünwald, Germany
Contact person: Hans Edel
EC Declaration of Conformity
We Home Skinovations Ltd. declare under our sole responsibility that the home Skin
treatment products
EN 55022:2006
EN 55024:1994;(A1:2001)(A2:2003)
EN 61000-3-2:2006; (A2:2005),
EN 61000-3-3:1995; (A1:2001)
Electrical Safety:
EMC:
Hans Edel
Europe
July 12, 2009
Brand Name
Model name
Silk’n Reju
Are fully in conformity with the essential requirements of EMC Directive 2004/108/EC and
Low Voltage Directive 2006/95/EC.
This declaration is based on the full compliaance of the products with the following
European standards:
Home Skinovations
Model Number
AS1018321
EN 60335-1:(2002),
EN 60335-2-23:(19963)
Gabi Lavi
General Manager
Yokneam, Israel
July 12, 2009

14
Apolo Building, Shaar Yokneam POB 533
Yokneam 20692, ISRAEL
tel. [phone], fax [phone]
[email protected], [email protected]
www.silkn.com