Home Styles 88566127 User manual

Hardware List
Small
Hex Wrench
Hex Wrench
1 pc.
1 pc.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
M7x60
Assembly Screw
20 pcs.(+1 extra)
M6x32
Wood Screw
for Handle
4 pcs.(+1 extra)
M6x25
Wood Screw
4 pcs.(+1 extra)
Adjustable Pin
8 pcs.(+1 extra)
M4x19
Wood Screw
for Door Hinge
24 pcs.(+1 extra)
A.
Top
1 pc. G.
Side Panel
1 pc.
H.
Side Panel
1 pc.
J.
Side Panel
1 pc.
M.
Door
1 pc.
O.
Door
1 pc.
P.
Door
1 pc.
N.
Door
1 pc.
K.
Side Panel
1 pc.
I.
Back Panel
1 pc.
L.
Back Panel
1 pc.
B.
Shelf
2 pcs.
C.
Middle Panel
1 pc.
D.
Base
1 pc.
E.
Stretcher
1 pc.
F.
Stretcher
1 pc.
Pull Handle
4 pcs.
Key
2 pcs.
88 5661 27
Storage Cabinet
Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.

Assembly Instructions 2/6
Assembly Screw
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the screws in the future.
* After assembly item must be level to work properly. Use the include adjustable levelers to level.
* Do not tighten up all the Screws unitl each part is properly assembled
* Use a soft cloth between these parts and the floor.
STEP 1
STEP 2
Attach Back Panel (L),
Base (D) and Stretchers (E) and (F)
to Side Panel (J) with Assembly Screws.
Attach Side Panel (K) to unit with Assembly Screws.
Attach Back Panel (I) to Side Panels (G) and (H)
with Assembly Screws.
J
K
D
F
E
L
I
G
H

Assembly Instructions 3/6
C
A
STEP 3
Attach Top (A) and Middle Panel (C)
to unit from Step 2 with Assembly Screws.
STEP 4
Attach unit form Step 1
to unit from Step 3 with Wood Screws.
Wood Screw

Assembly Instructions 4/6
Adjustable Pin
Figure 1
Figure 3
Figure 4 Figure 5
Figure 6 Figure 7
Figure 2
STEP 5
Insert Adjustable Pins into side panels at
the desired level (See Figure 1) then place,
Shelves (B) into position.
Attach Doors (M), (N), (O) and (P) to unit with
Wood Screws for Door Hinge. (See Figure 2)
Assemble Pull Handles to Doors with
Wood Screws for Handle. (See Figure 3)
Move the door catch up then turn left to lock
the door and turn right then pull down to unlock.
(See Figures 4, 5)
Turn Key counter clockwise to lock the door
and clockwise to unlock. (See Figure 6)
To level the unit, adjust the adjustable
levelers on the bottom of legs.
(See Figure 7)
B
B
M
N
O
P

Assembly Instructions 5/6
Wood Screw
Wall Screw
M3.5x16
Wood Screw
1 pc.(+1 extra)
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Drill 3/8” hole in wall
Top of unit
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x38
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole Bracket at
top of unit
Tipover
Restraint

Assembly Instructions 6/6
IMPORTANT NOTICE
If the magnetic door catches are too strong and difficult to open, the magnetic power can be
reduced and the door made easier to open by doing the following:
Magnet
location.
Loosen the Screws
only halfway.
Tighten the Screws. New position.
Rotate
the Magnet
until one Screw
is all the way forward
and the other Screw is all the
way back in the catch slots.
Magnet position.
1
3
56
4
2
Magnet
Magnet