Home Styles 88 5180 692 User manual

Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
88 5180 692
Buffet
Carton 88 5180 691 is also needed for assembly.
B.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
C.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
F.
Back Panel
3 pcs.
G.
Back Piece
2 pcs.
K.
Fixed Shelf
1 pc.
J.
Front Piece
1 pc.
S.
Drawer
2 pcs.
H.
Back Stretcher
2 pcs.
I.
Front Piece
1 pc.
Refer to later page(s) of these
instructions for drawer assembly.
Q.
Door
1 pc.
R.
Door
1 pc.

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
Figure 1
Figure 2
Figure 3
BC
DE
Wood Screw
for Magnet
Magnet
Cam Lock Screw
STEP 1
Insert Cam Lock Screws into pre-drilled holes of Side Panels (B), (C)
and Middle Panels (D), (E). (See Figure 1)
Attach Magnets to Middle Panels (D) and (E) with Wood Screws for Magnet.
(See Figure 2)
STEP 2
Attach Back Stretcher (H) to
Side Panel (B) with Cam Lock.
(See Figure 3)
Attach Back Pieces (G) to unit
and slide Back Panels (F) into place.
Attach Back Stretcher (H)
to unit with Cam Locks.
H
H
B
F
F
F
G
G
Cam Lock

Assembly Instructions 3/6
STEP 4
Attach Base (N) to unit with Head Cap Bolts.
Cam Lock
STEP 5
Attach Legs (O) to unit with Head Cap Bolts.
Attach Leg (P) to unit.
P
O
Head Cap Bolt
O
N
Head Cap Bolt
STEP 3
Attach Front Piece (I) to unit.
Attach Middle Panel (D) to unit with
Head Cap Bolts. (See Figure 4)
Attach Fixed Shelf (K) and Front
Piece (J) to unit with Cam Locks.
Attach Middle Panel (E) to unit with
Cam Locks and Head Cap Bolts.
Attach Side Panel (C) to unit with
Cam Locks.
Figure 4
D
E
C
I
K
J
Head Cap Bolt

Part List
Assembly Instructions 4/6
STEP 6
Attach Drawer Front (S1) and Drawer
Back (S2) to Drawer Side (S3) with
Wood Screws (long).
Attach Drawer Side (S4) to unit with
Wood Screws (long).
STEP 7
Slide Drawer Bottom (S5) into the grooves
of Drawer Sides (S3) and (S4) until it meets
Drawer Front (S1).
Attach Drawer Bottom (S5) to unit with
Wood Screws (short).
STEP 8
Attach Drawer Pull Handle with Machine Screws.
S1.
Drawer Front
2 pcs.
S2.
Drawer Back
2 pcs.
S3.
Drawer Side
2 pcs.
S4.
Drawer Side
2 pcs.
S5.
Drawer Bottom
2 pcs.
S1
S2
S3
S4
S5
Drawer (S)
S1
S2
S3
S4
Roller at back
Bottom

Assembly Instructions 5/6
STEP 9
Attach Rack (M) to Top (A)
with Head Cap Bolts.
A
MHead Cap Bolt
Figure 5 Figure 6
M
STEP 10
Turn unit to its’ upright position.
Attach Door Pull Handles
to Doors (Q) and (R) with
Machine Screws.
(See Figure 5)
Attach Doors (Q) and (R) to unit
by sliding door lift hinges
into side panel lift hinges.
(See Figure 6)
Attach Top (A) to unit
with Head Cap Bolts.
Insert Adjustable Pins into
side panels and middle panels
at desired level. (See Figure 7)
Place Shelves (L) into position.
Slide Drawers (S) into place.
A
L
L
Q
R
L
L
S
S
Figure 7
Figure 8
Head Cap Bolt
Adjustable Pin
Wood Screw (short)
STEP 11
Level unit by adjusting the adjustable levelers
on bottom of unit. (See Figure 8)
Insert Wood Screws (short) into
pre-drilled holes of unit.
Note: Unit must be level before
tightening these screws.

Assembly Instructions 6/6
Hardware List
STEP 12
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 9
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319