Home Styles Executive Desk 5436-15 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level
Executive Desk
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
M4x38
Machine Screw (long)
1 pc.
Knob
5 pcs.
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
Flat Washer
17 pcs. (+1 extra)
M6x35
Head Cap Bolt
17 pcs. (+1 extra)
Cam Lock
6 pcs. (+2 extra)
Cam Lock Screw
6 pcs. (+1 extra)
M3x15
Wood Screw
6 pcs. (+1 extra)
M4x28
Machine Screw
4 pcs.
Refer to the last page(s) of these
instructions for drawer assembly.
B.
Side Frame
1 pc.
C.
Side Frame
1 pc.
D.
Middle Panel
1 pc.
E.
Middle Panel
1 pc.
A.
Top
1 pc.
F.
Back Panel
1 pc.
G.
Back Stretcher
1 pc.
H.
Front Stretcher
1 pc.
I.
Front Stretcher
2 pcs.
J.
Drawer
2 pcs.
K.
Keyboard
1 pc.
L.
Keyboard Front
1 pc.
M4x38
Wood Screw (long)
2 pcs. (+1 extra)
Spring Washer
17 pcs. (+1 extra)

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled
holes of Side Frames (B), (C) and
Middle Panels (D), (E). (See Figure 1)
Spring Washer
B
C
D
E
Cam Lock Screw
Figure 1
F
H
D
E
Cam Lock Screw
Cam Lock
Head Cap Bolt
Flat Washer
STEP 2
Attach Middle Panels (D) and (E) to Front Stretcher (H) with Cam Locks.
(See Figure 2)
Attach unit to Back Panel (F) with Flat Washers, Spring Washers and
Head Cap Bolts. (See Figure 3)
Figure 2
Figure 3

Assembly Instructions 3/5
STEP 4
Attach Front Stretchers (I) to unit with Cam Locks.
Attach Side Frame (C) to unit with Cam Lock, Flat Washers, Spring Washers and Head Cap Bolts.
Spring Washer
Head Cap Bolt
Flat Washer
A
STEP 3
Place Top (A) upside down on a soft cloth.
Attach unit to Top (A) with Flat Washers,
Spring Washers and Head Cap Bolts.
C
I
Spring Washer
Cam Lock
Head Cap Bolt
I
Flat Washer

Assembly Instructions 4/5
STEP 5
Attach Back Stretcher (G) to unit
with Wood Screw (long).
(See Figure 4)
Attach Side Frame (B) to unit with
Flat Washers, Spring Washers,
Head Cap Bolts, Cam Lock and
Wood Screw (long).
K
L
STEP 6
Attach Keyboard Front (L) to Keyboard (K)
with Wood Screws. (See Figure 5)
Attach Knob to Keyboard Front (L) with
Machine Screw (long). (See Figure 6)
Figure 8 Figure 9
Left Side Right Side
STEP 7
Turn unit from Step 5 over
to its’ upright position.
Level unit by adjusting the adjustable
levelers on the bottom of legs.
(See Figure 7)
Slide Drawers (J) and
Keyboard into position.
Note: To remove Keyboard in the
future, push the plastic lever on
the left side up, push the plastic
lever on the right side down and
pull open slowly.
(See Figures 8 and 9)
Figure 5 Figure 6
Figure 7
Figure 4
Wood Screw
B
Wood Screw (long)
Cam Lock
Spring Washer
Head Cap Bolt
Flat Washer
G
JJ

Part List
Assembly Instructions 5/5
STEP 1
Attach Drawer Sides (J3) and (J4) to
Drawer Back (J2), then flip the locks.
(See Figures 1 and 2)
Figure 1 Figure 2
STEP 3
Attach Knobs with Machine Screws.
STEP 2
Slide Drawer Bottom (J5) into the grooves
of Drawer Sides (J3) and (J4) until it meets
Drawer Back (J2).
Attach Drawer Front (J1) to unit, then flip
the locks.
J1.
Drawer Front
2 pcs.
J2.
Drawer Back
2 pcs.
J3.
Drawer Side
2 pcs.
J4.
Drawer Side
2 pcs.
J5.
Drawer Bottom
2 pcs.
Drawer (J)
J2
J3
J4
Roller at back
Lock
J1
J5
J2
J3
J4

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale.