Home Styles Bar 20 05053 0099 User manual

Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
20 05053 0099
Bar
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Tool(s) required for assembly: LevelPhillips screwdriver,
A.
Frame
1 pc.
B.
Frame
1 pc.
C.
Frame
1 pc.
D.
Side Panel
1 pc.
E.
Side Panel
1 pc.
K.
Back Panel
1 pc.
L.
Back Panel
1 pc.
N.
Back Panel
1 pc.
M.
Strip
1 pc.
P.
Door
1 pc.
Q.
Door
1 pc.
O.
Door
1 pc.
F.
Top
1 pc.
G.
Shelf
1 pc.
I.
Shelf
2 pcs.
J.
Support
2 pcs.
H.
Bottom
1 pc.

Hardware List
20 05053 0099
Bar
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Tool(s) required for assembly: LevelPhillips screwdriver,
Handle
3 pcs.
M4x25
Machine Screw
6 pcs.
Hinge A
2 pcs.
Hinge C
4 pcs.
Flat Washer
14 pcs. (+1 extra)
Spring Washer
14 pcs. (+1 extra)
M6x16
Head Cap Bolt
14 pcs. (+1 extra)
M6x25
Tapered Bolt (short)
4 pcs. (+1 extra)
M6x38
Tapered Bolt (long)
12 pcs. (+1 extra)
M3.5x15
Hinge C Screw
24 pcs. (+1 extra)
M3x16
Hinge A, B Screw
24 pcs. (+1 extra)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Magnet
2 pcs.
M3.5x16
Wood Screw (short)
22 pcs. (+1 extra)
M3.5x28
Wood Screw (long)
6 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+1 extra)
Hinge B
2 pcs.

Assembly Instructions 3/9
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
HA
Tapered Bolt (short)
Tapered Bolt (long)
Pre-drilled holes on back
Magnet
STEP 1
Attach Magnets to Frame (A)
with Tapered Bolts (short).
(See Figure 1)
STEP 2
Noted: All parts in this step have pre-drilled holes on back;
orientate the pre-drilled holes up during this step.
Attach Frames (A), (B) and (C) to Side Panel (D) with Tapered Bolts (long),
tightening bolts only halfway. (See Figure 2)
Attach Side Panel (E) to unit with Tapered Bolts (long),
tightening bolts only halfway.
Figure 1
Figure 2
A
B
C
D
E

Assembly Instructions 4/9
STEP 3
Align Frames (A), (B) and (C) flush
with Side Panels (D) and (E).
(See Figure 3)
Tighten all bolts used in Step 2.
Figure 3
Flush
Flush
Flush
Flat Washer
Spring Washer
Head Cap Bolt
F
G
H
Figure 4
STEP 4
Attach Top (F), Shelf (G) and Bottom (H) to unit with Head Cap Bolts, Spring Washers
and Flat Washers, tightening bolts only halfway. (See Figure 4)
Tighten all bolts used in this step.
A
B
C
E
D

Assembly Instructions 5/9
STEP 5
Attach Back Panels (K) and (L) to unit
with Wood Screws (short) into pre-drilled holes,
tightening screws only halfway. (See Figure 5)
STEP 6
Attach Strip (M)
to Back Panel (L).
(See Figure 6)
Insert edge of Back Panel (N) into Strip (M)
and attach to unit with Wood Screws (short)
into pre-drilled holes, tightening screws only halfway.
Figure 5
L
K
Wood Screw (short)
Figure 6 N
M
L
Wood Screw (short)

Assembly Instructions 6/9
Figure 8
Wood Screw (long)
Figure 7
Hinge A, B Screw
Hinge A
OJ
JI
I
STEP 7
Attach Hinges A to Door (O) with
Hinge A, B Screws. (See Figure 7)
Attach Supports (J) to Shelves (I) with Wood Screws (long)
into pre-drilled holes. (See Figure 8)
STEP 8
Insert Adjustable Pins into side panels
at desired level. (See Figure 9)
Place Shelves (I) into position.
Attach Door (O) to unit with Hinge A, B Screws. (See Figure 10)
I
I
Hinge Screw A, B
Adjustable Pin
Figure 10Figure 9
O

Assembly Instructions 7/9
STEP 9
Attach Hinges B to Door (O) and side panels with Hinge A, B Screws into pre-drilled holes.
(See Figures 11 and 12)
Attach Handle to Door (O) with Machine Screws.
Hinge A, B Screw
Hinge A, B Screw
Hinge B
Machine Screw
Handle
O
Figure 11
Figure 12
STEP 10
Level unit by adjusting the adjustable levelers
on bottom of unit. (See Figure 13)
Note: Unit must be level to work properly.
Tighten all wood screws used in Steps 5 and 6.
Figure 13 Screwdriver

STEP 11
Attach Hinges C to side panels with Hinge C Screws
into pre-drilled holes. (See Figure 14)
Attach Doors (P) and (Q) to unit
with Hinge C Screws into pre-drilled holes.
(See Figure 15)
Attach Handles to Doors (P) and (Q)
with Machine Screws.
Assembly Instructions 8/9
Figure 14
Figure 15
Figure 16 Figure 17
P
Q
Machine Screw
UP Front Back
Down
Hinge C
Hinge C Screw Handle
If needed, adjust Doors (P) and (Q) up or down by removing the front Hinge C Screws and
loosening slightly the back Hinge C Screws from side panel, adjusting door up or down and
re-installing screws. (See Figures 16).
If needed, adjust Doors (P) and (Q) left to right. (See Figure 17)
If needed, adjust Doors (P) and (Q) front to back. (See Figure 18)
Figure 18
Left
Right

Assembly Instructions 9/9
Hardware List
STEP 12
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Machine Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 19)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
Figure 19
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Machine Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
M4x10
Machine Screw
1 pc. (+1 extra)

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts