Home Styles 20 05003 0992 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Cam Lock
39 pcs. (+6 extra)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Adjustable Pin
12 pcs. (+1 extra)
Magnet
1 pc.
M3x15
Tapered Wood Screw
12 pcs. (+1 extra)
M6x10
Head Cap Bolt (short)
3 pcs. (+1 extra)
Flat Washer
11 pcs. (+1 extra)
Head Cap Bolt
11 pcs. (+1 extra)
M6x25
Knob
2 pcs.
Machine Screw
2 pcs.
M4x25
Wood Screw (long)
M3x25
8 pcs. (+1 extra)
Side Panel
D.
2 pcs.
J.
Side Panel
1 pc.
K.
Side Panel
1 pc.
L.
Middle Panel
1 pc.
F.
Front Rail
2 pcs.
M.
Base
1 pc.
O.
Shelf
3 pcs.
R.
Drawer
1 pc.
P.
Foot Rest Support
3 pcs.
20 05003 0992
Bar
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Tool(s) required for assembly: LevelPhillips screwdriver,
Carton 20 05003 0991 is also needed for assembly.
Cam Lock Screw
39 pcs. (+2 extra)
Refer to later page(s) of these
instructions for drawer assembly.
M3x12
Wood Screw
for Magnet
2 pcs. (+1 extra)
Q.
Foot Rest
1 pc.

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
H
L
A
BL
K
H
H
I
M
Cam Lock Screw
STEP 1
Insert Cam Lock Screws into pre-drilled holes of Top (A), Sub Top (B), Front Panels (H), (I),
Side Panel (K), Middle Panel (L) and Base (M), then tighten. (See Figure 1)
Note: Insert Cam Lock Screws into Sub Top (B) in the holes exactly as shown below.
(See Figure 2)
B
Do put Cam Lock Screws in these holes.not
Figure 1
Figure 2

Head Cap Bolt
Cam Lock
Assembly Instructions 3/7
B
C
D
D
A
STEP 2
Place Top (A) upside down on a soft cloth.
Attach Side Panels (D) and Front Panel (C) to Top (A) with Cam Locks.
Attach Sub Top (B) to top unit with Head Cap Bolts and Flat Washers.
(See Figure 3)
Figure 3
H
H
I
STEP 3
Attach Front Panels (H) to Front Panel (I) with Cam Locks.
Flat Washer
Cam Lock

Assembly Instructions 4/7
Figure 4
STEP 5
Attach Side Panels (J) and (K) to
unit from Step 3, then attach unit
to Base (M) with Cam Locks.
Attach Front Rails (F) to unit with
Cam Locks.
Attach Middle Panel (L) to unit with
Cam Locks.
STEP 4
Attach Magnet to Middle Panel (L) with Wood Screws
for Magnet into pre-drilled holes. (See Figure 4)
F
F
K
J
L
M
L
Cam Lock
Wood Screw for Magnet
Magnet
Cam Lock

Assembly Instructions 5/7
Part List
R1.
Drawer Front
1 pc.
R2.
Drawer Back
1 pc.
R3.
Drawer Side
1 pc.
R4.
Drawer Side
1 pc.
R5.
Drawer Bottom
1 pc.
STEP 8
Attach Knob with Machine Screw.
STEP 6
Attach Drawer Front (R1) and Drawer Back (R2)
to Drawer Side (R3) with Wood Screws (long).
STEP 7
Slide Drawer Bottom (R5) into the grooves
of Drawer Front (R1) and Drawer Back (R2)
until it meets Drawer Side (R3).
Attach Drawer Side (R4) to unit
with Wood Screws (long).
R1
R2
R4
R3
R5
Knob
R1
R2 R3
Drawer (R)
Roller at back
Wood Screw (long)
Machine Screw
Wood Screw (long)

Cam Lock
Machine Screw
Head Cap Bolt
Assembly Instructions 6/7
Figure 7
E
R
O
O
O
N
STEP 9
Insert Adjustable Pins into middle panel and
side panels at the desired level. (See Figure 5)
Slide Shelves (O) into position.
Attach Door (N) to unit by sliding door hinges
into side panel hinges. (See Figure 6)
Attach Knob to Door (N) with Machine Screw.
(See Figure 7)
Attach unit from Step 2 to unit with Cam Locks.
Attach Glass Holder (E) to unit with
Head Cap Bolts and Flat Washers.
Slide Drawers (R) into position.
Level unit by adjusting the adjustable
levelers on bottom of unit. (See Figure 8)
Note: Unit must be level to work properly.
Figure 6
Figure 8
Figure 5
Knob
Adjustable Pin
Flat Washer

P
Tapered
Wood Screw
Same amount of
Foot Rest (Q) on
each side
Head Cap Bolt
(short)
Assembly Instructions 7/7
STEP 10
Slide Foot Rest (Q) into Foot Rest Supports (P).
Attach Foot Rest Supports (P) to unit with Tapered Wood Screws
into pre-drilled holes.
Attach Foot Rest (Q) to Foot Rest Supports (P) with
Head Cap Bolts (short), leaving same amount of Foot Rest (Q)
protruding on outside of outer Foot Rest Supports (P).
(See Figure 9)
Figure 9
P
P
P
Q

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319