HOMEDEPOT L-DN615SST User manual

Assembly Instructions
L-DN615SST (Bar)

Hardware
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
（H1）×28
M6 *15 bolt
（H4）×2
M8*15 bolt
（H5）×2
M6*55 bolt
（H3）×2
M8 *130 bolt
（H6）×3
M6 *25 bolt
（H7）×33
M6 flat washer
（H8）×4
M8 flat washer
（H9）×2
M8 nut
（H10）×4
M5*15 bolt
（H11）×1
M6/ M8 wrench

ITEM DESCRIPTION QUANTITY
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
A. cover board １
B. connecting piece 2
C. cover 1
D. cup rack 1
E. post 2
F. support bar 2
G. table top 1
H. connecting piece 4
I. front panel 1
J1. left clapboard 1
J2. right clapboard 1
K. bottom shelf 1
L1. left foot rail rack 1
L2. right foot rail rack 1
M. foot rail 1

．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
1. Connect front panel I and clapboard J1 & J2 by using connecting piece H, bolt (H1) & flat washer (H7). （As shown in Fig.1, Fig.2.)
（H1
H1
H1
H1
H1
）×8
M6 *15 bolt
（H7
H7
H7
H7
H7
）×8
M6 flat washer
Step 1.
(Using wrench H11)
I

Step 2.
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
2. Attach bottom shelf (K）to enclosure bar, using bolt H1 and flat washer H7 to secure them as below diagram shown. Repeat this step for the
other side (Using wrench H11)
（H7）×4
M6 flat washer
（H1
H7
H1
H7
H1
）× 4
M6 *15 bolt

Step 3.
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．
3. Connect table top (G) and finished clapboard (I, J1, J2) with 6pcs bolts (H1) and flat washer (H7).
(Using wrench H11)
（H7）×6
M6 flat washer
（H1
H7
H7
H7
H1
H1
H1
）×6
M6 *15 bolt

Step 4.
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
4.1 Insert 2pcs posts (E) into holes on bar top (G) until touch the bottom shelf (K), then connect with post (E) through clapboard (J1)
with bolt H3, flat washer H8 and nut H9,as shown in Fig.1.(Using wrench H11)
4.2. Connect post (E) and bottom shelf (K) with bolt H4 and flat washer H8, as shown in Fig.2. (Using wrench H11)
4.3. Insert support bar (F) into holes on post(E), the holes should face the inside for proper assembly later on, as shown in Fig.3.
（H3）×2
M8 *130 bolt
（H8）×4
M8 flat washer
（H9）×2
M8 nut
（H4）×2
M8*15 bolt

Step 5.
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
5. place cover (C) on the post and support bars (F), fix support bars to post by using bolt (H1) and flat washers (H7)
separately, as below diagram shown.(Using wrench H11)
（H1
H7
H1
）×4
M6 *15 bolt
（H7）×4
M6 flat washer

Step 6.
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
6.1. Put bolt H5 through connecting piece (B) and top (C), then connect with post (E), tighten with bolts (H5) and flat washer
6.2. Attach cover board (A ) to top (C), tighten with bolts H6 and flat washer (H7).(Using flat wrench H11)
（H5）×2
M6*55 bolt
（H6）×3
M6 *25 bolt
（H7）×5
M6 Flat washer
(H7). as shown in Fig.1.

Step 7.
Step 8.
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
7.1. Attach cup rack (D) to cover (C) by
Pls tighten all bolts.
using cross bolt (H10), as shown in Fig.1.
7.2. Fix foot rail rack(L1,L2) with clapboard (J1,J2) by using bolt(H1) and flat washer (H7) . Then fix foot rail (M) with foot rail
rack(L1,L2) by using bolt(H1) and flat washer(H7) , as shown in Fig.2. (Using wrench H11)
（H10）×4
M5*15 bolt
（H1）×6
M6 *15 bolt
（H7）×6
M6 flat washer

Limited Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of your item provided the item
is maintained with care and used only for personal, residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of 6 months . We don't reimburse for transportation or
delivery costs, or compensate the individual or any outside party for assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature, vandalism, misuse, or
improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for
warranty claims. Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items will be in the original style
and color, or a similar style and color if the original is unavailable or has been discontinued. As some states do not allow exclusions or
limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights, and you may
also have other rights, which vary from state to state.
Care & Maintenance:
1. Before using, clean the bar completely with a soft dry towel.
2. Do not place your bar in wet conditions where there is a risk of rust developing.
3. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely. Do
not use strong detergent or abrasive cleaners.
4. When not in use, store in a cool, dry location away from sunlight
.
Made in China

Assembly Instructions
L-DN615SST (Stool)

Hardware
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
（H1）×8
M6 *15 bolt
（H2）×8
M6 flat washer
（H3）×8
M6 spring washer

ITEM DESCRIPTION QUANTITY
．
．．
．．．
．．．
．．．．
．．．
．．．
．．
．．
．．．
．．．
．．．．
．．．
．．．
．．
．．
．．．
．．．
．．
．．
．．．
．．
．．．
．．
．．．．．．．．．．．．．．．．
．．
．．．．．．．．．．．．．．．．．．
．
．．．
．．．
．．．．．．．．．
A. stool top 1
B. stool leg 2
C. support bar2

．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
Step 1.
Attach C to B by using bolt H1, flat washer H2, spring washer H3, not tighten fully．
Note: Do not fully tighten the hardwares at this step.
（H1）×4
M6 *15 bolt
（H2）×4
M6 flat washer
（H3）×4
M6 spring washer

．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
Step 2.
Insert top end of leg B into the tube on the backside of the stool top ( A) , secure with bolt H1, spring washer H3 and flat washer H2.
（H1）×4
M6 *15 bolt
（H2）×4
M6 flat washer
（H3）×4
M6 spring washer
Step3.
Now, please tighten all bolts and turn it over then.
H1
H3
H2

Limited Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of your item provided the item
is maintained with care and used only for personal, residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of 6months. We don't reimburse for transportation or
delivery costs, or compensate the individual or any outside party for assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature, vandalism, misuse, or
improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for
warranty claims. Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items will be in the original style
and color, or a similar style and color if the original is unavailable or has been discontinued. As some states do not allow exclusions or
limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights, and you may
also have other rights, which vary from state to state.
Care & Maintenance:
1. Before using, clean the barstool completely with a soft dry towel.
2. Do not place your barstool in wet conditions where there is a risk of rust developing.
3. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely. Do
not use strong detergent or abrasive cleaners.
4. When not in use, store in a cool, dry location away from sunlight
.
Made in China