Homelegance 2459 User manual

1
ASSEMBLY INSTRUCTIONS
ITEM: 2459 / 2459(3A)
6pcs Pack Dinette / Espresso
This page lists all the contents included in the box. Please take the time to identify
the hardware as well as the individual components to this product. As you unpack
and prepare for assembly, place the contents on a carpeted or padded area to
protect them from damage.
c l e a n i n g & c a r e Treat surface with care. Clean surfaces with a dry or
damp soft cloth. Do not use abrasive cleaners. Hardware may loosen over time.
Periodically check that all connections are tight.
A Phillips head screwdriver is necessary for assembly.

2
TABLE PART LIST
A. TABLE TOP 1 PC
B. TABLE LEG 4 PCS
A
B
B
B
B

TABLE ASSEMBLY INSTRUCTIONS
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
2.
8 PCS
SPRING WASHER
3.
8 PCS
1.
8 PCS
OPEN WRENCH
4. 1 PC
FLAT WASHER
1. Place table top (A) upside down
on a non-abrasive surface such
as carpet (underside of tabletop
should be facing up).
2. Attach the legs (B) to the apron
of table top (A) using 8 flat
washers (1), 8 spring washers (2),
and 8 nuts (3) as shown.
DIAGRAM #1
3. Turn the table upright. Make sure the table is level, and tightly fasten
all nuts (3) using the open-end wrench (4) as shown.
The table is now ready for use
3
1234
NUT
A
B
BB
B
DIAGRAM #2

CHAIR PART LIST
C. CHAIR BACK 4 PCS
D. SEAT FRAME 4 PCS
E. FRONT LEG 8 PCS
F. CUSHION 4 PCS
4
C
D
E
F

5
DIAGRAM #3
CHAIR ASSEMBLY INSTRUCTIONS
DIAGRAM #4
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1. 4 PCS
SPRING WASHER
2. 4 PCS
FLAT WASHER
OPEN WRENCH
4. 1 PC
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1. Attach 2 front legs (E) to seat frame (D) using 4 nuts (3), 4 spring
washers (2), and 4 flat washers (1) as shown.
Note: The seat frame (D) has 2 holes on each side,which are used to
attach the seat. These holes are wider on the bottom and narrower
on the top. Ensure the wider holes are facing towards you.
2. Attach the seat frame (D) to the chair back (C) using 3 short bolts (5),
4 long bolts (6), 7 spring washers (2), and 7 flat washers (1) as shown.
Do not fully tighten.
3. Turn the chair upright. Make sure the assembled chair unit is level and
square. Tightly fasten all nuts (3) and bolts (5&6) with the open-end
wrench (4).
1234
NUT
3. 4 PCS
E
E
D
E
PLASTIC PLUG
1. 7 PCS
SPRING WASHER
2. 7 PCS
FLAT WASHER
OPEN WRENCH
4. 1 PC
SHORT BOLT
5.
LONG BOLT
6.
3 PCS
4 PCS
4
6
2
1
2
15
C
D
EE

6
CHAIR ASSEMBLY INSTRUCTIONS
DIAGRAM #5
The chair is now ready for use.
6. Repeat diagram #3 to #6 to assemble the other chairs.
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
7. 6 PCS
WOOD SCREW
4. Place cushion seat (F) upside down on a non-abrasive table surface. The rear ( tapered end ) of the
cushion seat (F) should be near the table edge.
Hint: Protect the non-abrasive table surface and cushion seat (F) by laying a towel in-between the
chair seat and table.
5. Place the assembled chair frame on the cushion seat (F) as shown. Attach with 6 wood screws (7).
Tighten the screws.
Turn the chair upright.
C
D
E
F
E
77777
7
DIAGRAM #6

G. CUSHION 1 PC
H. SEAT FRAME 1 PC
I. LEFT FRONT/RIGHT BACK LEG 2 PCS
J. RIGHT FRONT/LEFT BACK LEG 2 PCS
K. SIDE PANEL 2 PCS
L. SIDE CROSSBAR 2 PCS
UP
BENCH PART LIST
J
I
JH
G
KL
L
7
I
K

8
BENCH ASSEMBLY INSTRUCTIONS
DIAGRAM #7
DIAGRAM #8
1. Attach 2 side panels (K) to seat frame (H) and side crossbars (L) as shown.
Note: The seat frame (I) has 4 holes on each long side, which are used to attach the seat
cushion. These holes are wider on the bottom and narrower on the top. Ensure the wider holes
are facing towards you.The side panel has different top and bottom joining points. Ensure the
joining points are perfectly match with seat frame and side crossbars.
L
L
KK
H
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1. 8 PCS
SPRING WASHER
2. 8 PCS
FLAT WASHER
OPEN WRENCH 1 PC
NUT
3. 8 PCS
4.
7. 4 PCS
WOOD SCREW
2. Attach bench legs (I & J) to seat frame (D) and side crossbars (L) using 8 flat washers (1), 8
spring washers (2), and 8 nuts (3) as shown. Screw 4 wood screws (7) to secure the crossbars (L).
Note: The bench leg has hole on its inner side to attach the crossbars. Make sure the holes facing
toward the crossbars.
I
I
J
J
L
L
H
77
77
1234
PLASTIC PLUG

Printed in Vietnam
9
BENCH ASSEMBLY INSTRUCTIONS
DIAGRAM #9
DIAGRAM #10
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
7. 8 PCS
WOOD SCREW
3. Place cushion seat (G) upside down on a non-abrasive surface.
Hint: Protect the non-abrasive table surface and cushion seat (F) by laying a towel in-between the chair seat
and table.
4. Place the assembled bench frame on the cushion seat (G) as shown. Attach with 8 wood screws (7). Tighten
the screws.
The bench is now ready for use.
Turn the bench upright.
H
G