HomeRun Qmotion QSYNC-433AM User manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: [phone]
Certification Exhibit
FCC ID: X6P-QSYNC433AM
IC: 8832A-QSYNC433AM
FCC Rule Part: 15.231
IC Radio Standards Specification: RSS-210
ACS Project Number: 12-0527
Manufacturer: HomeRun Holdings
Model: QSYNC-433AM
Manual

sync
Network Gateway for Qmotion Automated Shades
www.qmotionshades.com
Verify the contents of the
Qsync package and gather
needed materials:
1. Ethernet cable.
2. Qsync
3. Antenna
4. Power Adapter
(Color may vary.)
Attach the antenna to the
Qsync by screwing it onto
the coaxial connector on
Qsync’s back plate. For
best performance, position
the antenna as high up
as possible and without
obstructions between it and
the shades.
Plug the power cord into
Qsync’s front plate. Then
plug it into a 120VAC 60Hz
outlet.
1 2
3
4
Coax Connector
Power connector

FCC COMPLIANCE
Warning: Changes or modifications to this device not expressly approved by HomeRun Holdings Corp. could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is con-
nected.• Consult the dealer or an experience radio/TV technician for help.
INDUSTRY CANADA COMPLIANCE
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter
by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type
d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication
satisfaisante.
This radio transmitter, Model: QSYNC-433AM, has been approved by Industry Canada to operate with types listed below with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum indicated for that type, are
strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de catégorie I) a été approuvé
par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque
type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de
l’émetteur.
Approved antenna: HomeRun Holdings P/N 6500034, 433MHz RP-SMA swivel antenna, 50Ω, 2.5dBi
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interfer-
ence, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
PRECAUTIONS STATEMENT
• Do not let the Qmotion Qsync get wet. Keep the Qsync away from rain and sea water.
Letting the Qsync get wet may cause the unit to malfunction, and sometimes this
malfunction cannot be repaired.• Never leave the Qsync exposed to temperatures above 140°F (60°C), such as in
an attic or under direct sunlight.
Connect Qsync to one
of your router’s LAN
ports using an ethernet
cable. Do not use the
Internet Port (shown
yellow.)
Open the App Store on
your Apple device and
search for “qmotion”.
Download the Qsync
app by clicking on the
“FREE” button. The
app will download.
Click the “INSTALL
NOW” button to finish
installation.
Open the app on
your device. The app
searches the WiFi
network connected to
your device for Qsync.
When it is found, click
on the Qsync device
you wish to control.
The five buttons on the
left control the shade
as a hand-held remote
would. The two buttons
at the bottom “jog” the
shade up or down. Try
each button to ensure
Qsync is working
properly.
NO
OK
OK
OK
OK
Back of Router
Internet Cable,
not for Qsync