Honeywell Home 5800SS1 User manual

5800SS1
Wireless Shock Sensor
Installation & Setup Guide
GENERAL INFORMATION
The 5800SS1 is a wireless shock sensor intended
for use in systems that support 5800 series devices.
Each transmitter has its own unique serial number,
assigned during manufacture, which must be
“enrolled” in the control panel before the device can
be used with the system. Refer to the control
panel's Installation and Setup Guide for
programming details. One 5800SS1 is required for
each pane of glass protected. (Do not use more
than one sensor per pane.)
Types of Glass Protection
•Tempered
•Ordinary Plate
•Sealed Insulated
Not for use in UL installations.
Note: It is not necessary to remove the case cover
during installation.
ENROLLING
You must enroll the 5800SS1 serial number in the
control panel using zone programming. Refer to the
control panel's Installation and Setup Guide for
detailed programming procedures. Before
programming, perform the following:
1. To cause the transmitter to transmit, remove
the “PULL TO CONNECT BATTERY” tab (see
Figure 1). (For additional transmissions, lightly
tap on the base of the sensor with a
screwdriver.)
Figure 1
2. When programming the shock sensor, note the
following:
•Input Type = 3 (Supervised RF)
•Loop Number = 1
3. When prompted for the serial number, you can
transmit by lightly tapping on the base of the
sensor with a screwdriver (pause 2 seconds
between taps) or by manually entering the
serial and loop number.
MOUNTING
1. Before the transmitter is permanently mounted,
determine the optimum mounting location. For
best sensitivity, the sensor should be mounted
one-inch from the corner edge of the window
frame (see Figure 2).
Figure 2
2. Conduct Go/No Go tests (see control’s
instructions) to verify adequate signal strength
from the mounting location to the Alarm
System receiver.
Verify range by taping (with masking tape) the
sensor in the approximate mounting location
and tapping at the base to initiate a fault
transmission. The panel (in the Go/No Go test
mode) should respond to the transmissions. If
not, find a more suitable mounting location,
possibly on the opposite corner of the window.
3. After successful testing. Clean the glass,
where the sensor will be mounted, with a
mixture of water and isopropyl alcohol.
4. Once the glass has dried, remove the tape
backing paper and firmly press the sensor in
the desired mounting location.
5. Verify operation by striking the center of the
glass with the handle of a large screwdriver.
Always check the alarm panel keypad to verify
that the correct zone has tripped.
6. Apply optional “WARNING” label to the
outside glass surface opposite the tape side of
the 5800SS1.
REPLACING THE BATTERY
1. Using a screwdriver, carefully remove the
sensor’s cover.
2. Check the battery polarity orientation before
installing (see Figure 3).
3. Insert the battery securely in the sensor.
4. Snap the sensor cover back in place.
Figure 3

SPECIFICATIONS
Glass Coverage:
Plate, Sealed Insulated, and Tempered glass,
with thicknesses between 3/32” (2.38mm) and
1/4” (6.35mm) and up to 7 ft (2.134m) distance
from mounting location. One sensor is required
for each separate pane of glass. Not for use in UL
installations.
Dimensions:
1.6" H x 1.6" W x 0.8" D (40.64 mm x 40.64 mm x
20.32 mm)
Power:
Single 3V Panasonic CR2, or Duracell DLCR2 Lithium
Battery
WARNING
Risk of fire, explosion, and burns. Do not recharge, disassemble, heat above 212º F (100º C) or incinerate.
Dispose of used batteries properly. Keep away from children.
FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, as defined by FCC Rules Part 15.105.
The Class B Digital Device statement can be viewed at:
https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspx
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and Industry Canada’s license-exempt RSSs. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute
interférence reçue y compris les interférences causant une réception indésirable.
Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2
Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000
The product should not be disposed of with other household waste. Check for the nearest authorized collection
centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative
consequences for the environment and human health.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's
Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
TO THE INSTALLER
Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are
vital to continuous satisfactory operation of any alarm system.
The installer should assume the responsibility of developing and offering a regular maintenance program to
the user as well as acquainting the user with the proper operation and limitations of the alarm system and its
component parts. Recommendations must be included for a specific program of frequent testing (at least
weekly) to ensure the system’s proper operation at all times.
FOR WARRANTY INFORMATION AND DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE
ALARM SYSTEM REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL
USED WITH THIS DEVICE.
SUPPORT & WARRANTY INFORMATION
For the latest documentation and online support information, please go to:
www.resideo.com
For the latest warranty information, please go to:
www.security.honeywellhome.com/warranty
The Honeywell Home Trademark is used under license from Honeywell International Inc.
This product manufactured by Resideo Technologies, Inc. and its affiliates.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2020 Resideo Technologies, Inc.
www.resideo.com
ÊK0011V2CpŠ
K0011V2C 12/13 Rev. C