Honeywell 8670 User manual

8670 Wireless Ring Scanner
Quick Start Guide
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Para Português, acesse www.honeywellaidc.com.br.
Перейти на русскоязычный сайт www.honeywellaidc.com.
查看繁体版请登陆 www.honeywellaidc.com
한글 www.honeywellaidc.com 로이동합니다 .
ʤʱʸʢʬʺʩʸʡʲʡʺʡʥʺʫʡʨʰʸʨʰʩʠʤʸʺʠʬʸʥʡʲwww.honeywellaidc.com.
Rev C
7/16

Ring Scanner Overview
Scan
Window
Trigger
Optional C-ring
in small and
large sizes to
replace ring
strap
Ring Strap
Bluetooth™
module
Solid blue LED
indicates you are
connected via
Bluetooth.
Note: The battery must be fully charged before the first use. The
8650 8-Bay Battery Charger must be purchased separately.

Trigger Rotation
Attach Ring to Finger
1. Remove the shipping film from the ring scanner window.
2. Slide your finger into the loosened ring strap.
3. Pull the ring strap to secure the ring to your finger.
Note: If using the C-ring, simply slide it on to your finger.
Left Hand Right Hand
Scanner head can
be rotated 180°

Shipping
film

Change Ring Strap to C-Ring
1. Turn the ring scanner 90°.
2. Press the latch down.
3. Remove the ring strap.
4. Reverse these directions to attach the C-ring.

Replace the Battery
If the LED on the ring scanner flashes red, it indicates the battery is
low. To replace the battery, push the button and slide the lock to
open the battery compartment on the Bluetooth™ module and
remove the battery.
Replace the battery in the compartment, aligning the yellow dots on
the battery and compartment, then slide the lock closed.

Wear the Ring Scanner
The ring cable should not cross under your hand.
Right handed - wear battery
module so Honeywell name is
facing toward you
Left handed - wear battery module
so Honeywell name is facing away
from you
Wrist Position When Scanning
Incorrect Incorrect
Correct

Warning: Do not stare directly into the laser beam.
How to Scan a Bar Code
1D bar codes 2D bar codes
Pair the Ring Scanner
The ring scanner can be used with Bluetooth devices, Honeywell
mobile computers, Honeywell vehicle mount computers, Honeywell
communication bases and Access Points.
Pair with a Bluetooth Device Using a HID Keyboard
The 8670 ring scanner can pair with host Bluetooth devices
such as personal computers, laptops, tablets, and Apple®
devices.
!

1. Scan the Bluetooth HID Keyboard Connect bar code
below.
2. Set your host device so it searches for other Bluetooth
devices. (Refer to your host device’s User’s Guide for pair-
ing instructions.)
3. Once your host device has located the scanner, select the
8670 ring scanner name from the list displayed.
Note: Select the serial number that is shown on the ring
scanner, not on the battery module.
4. Some host devices will automatically pair with the ring
scanner. If your host device automatically pairs with the
ring scanner, it displays a successful pairing message and
you do not need to continue to the next step.
5. Some PDT hosts display a prompt for a PIN. Ignore this
message.
6. If your host device does not automatically pair with the ring
scanner, a PIN is displayed. This PIN must be scanned
within 60 seconds. Using the ring scanner, you must
quickly scan Bluetooth PIN Code below, then scan the
numeric bar code(s) for the PIN code from the
Programming Chart, then scan the Save bar code.
Bluetooth HID Keyboard Connect
Bluetooth PIN Code

When the ring scanner pairs with a host, the LED on the top of
the ring scanner flashes green and the LED on the Bluetooth
module remains solid blue. Your host device should now be
paired with the ring scanner and be able to accept incoming
data from the 8670.
Use the On-Screen Keyboard
If you have paired with an Apple device, the on-screen key-
board is activated by pressing the ring scanner trigger
twice, quickly. If you have paired with an Android device (v
4.4 and higher), the on-screen keyboard must be config-
ured by going to Settings - Language & input. Tap on
Default and change the setting for Hardware Physical
keyboard to Off.
Disconnect from Host
Once your ring scanner has been connected to a host, you
must disconnect it in order to communicate with a different
device. Scan the Bluetooth HID Keyboard Disconnect bar
code to unlink the ring scanner from the currently linked host.
Pair with a Bluetooth Serial Port - PCs/Laptops
The 8670 ring scanner can pair with a Bluetooth serial port on a
PC or laptop.
1. Scan the Non-Base BT Connection bar code below.
Bluetooth HID Keyboard Disconnect
Non-Base BT Connection

2. Set your host device so it searches for other Bluetooth
devices. (Refer to your host device’s User’s Guide for pair-
ing instructions.)
3. Once your host device has located the scanner, select the
8670 ring scanner name from the list displayed.
Note: Select the serial number that is shown on the ring
scanner, not on the battery module.
4. If a PIN is requested, enter 1234 (the default).
When the ring scanner pairs with the serial port of the host, the
LED on the top of the ring scanner flashes green and the LED
on the Bluetooth module remains solid blue. Your host device
should now be paired with the ring scanner and be able to
accept incoming data from the 8670.
Pair with a Honeywell Mobile Computer
The 8670 ring scanner can pair with Honeywell mobile comput-
ers such as the Dolphin 70e or 75e. (For Tecton mobile com-
puters, see Pair with a Honeywell Vehicle Mount Computer
instructions that follow.)