Honeywell CM4680 User manual

CM4680 2D Imager Module
Quick Start Guide
CM4680-EN-QS Rev a
6/21

1
What is the CM4680 2D Imager Module
The CM4680 is an encased compact 2D imager module for fixed
mount applications.
The CM4680 2D imager module includes the following features:
• USB interface (micro USB connector)
•Exitwindow
• Beeper
• Status indicator
• Mounting holes for multiple mounting positions
• Sealed enclosure
Required Accessories (not provided)
• Standard USB cable (USB-A to micro USB). Maximum
recommended length is 3-5 meters.
Additional Documentation
The following document is available from your local Honeywell
OEM representative:
• N4680/CF4680/CM4680 User Guide

2
CM4680 2D Imager Module Views
Status
indicator
Exit
window Mounting
holes (x10)
Mounting
holes (x10)

3
Beeper
USB cable
Slider to
secure cable
Mounting
holes (x10)
Mounting
holes (x10)

4
Connecting to a Host
By default, the scanner is in USB serial interface.
1. Remove slider from module by pressing the ends and slid-
ing it off.
2. Connect a standard USB cable (standard USB-A to micro
USB) to the module.
USB cable

5
3. Secure the cable to the module using the slider:
Place the cable through the center of the slider.
Press the ends of the slider and slide it back on to the mod-
ule until tight.
4. Connect the USB cable to the host.
5. Power-up the host.
The scanner powers up, emits a series of beeps from low to
high, and lighting turns on.
Note: The host does not have to be powered down before
plugging in the device. It can be hot plugged.

6
Configuration
You can configure your scanner two ways:
• Reading configuration bar codes
• Using the EZConfig Cloud for Scanning tool
Configuration Bar Codes
Scan configuration bar codes to set up your scanner. All avail-
able configuration bar codes are available in the N4680/
CF4680/CM4680 User Guide. Contact your local Honeywell
OEM representative for more information.
EZConfig for Scanning Tool
Use the EZConfig for Scanning tool to configure your scanner
Online:
1. Go to the Honeywell https://hsmftp.honeywell.com.
2. Register (if you haven’t already), then login.
3. Browse to Software >Barcode Scanners > Software > Tools
and Utilities > EZConfig for Scanning > Current and
download the tool.
4. Open EZConfig to configure your scanner.

7
Basic Setup
Here are some basic menu bar codes that may be useful for test-
ing. For more setup options see the N4680/CF4680/CM4680
User Guide (available from your local Honeywell OEM represen-
tative).
Note: The * symbol indicates the default value.
Interface
For USB serial interface, you must install the USB driver before
connecting your scanner. You can find the most current USB
driver at hsmftp.honeywell.com.
USB Serial Interface *
USB PC Keyboard

8
Keyboard Country Layout
the default keyboard is United States.
United States *
French
German
Italian

9
Beeper Volume
Low
Medium
High *
Off

10
Presentation Mode
The scanner LEDs remain dim and aimer off until a movement is
detected, then the aimer turns on and LEDs light up to read the
bar code.
There are 2 types: Presentation Mode or Presentation Mode—
Extended Reading Range.
Presentation Mode: Optimized scan speed, limited reading
range.
Presentation Mode *
Presentation Mode—Extended Reading Range: Optimized read-
ing range, low scan speed.
Presentation Mode—Extended Reading Range
Mobile Phone Read Mode
When this mode is selected, your scan engine is optimized to
read barcodes from mobile phones or other LED displays.
Streaming Presentation - Mobile Phone

11
Streaming Presentation
The scanner LEDs are on all the time (continuous) and the aimer
is off until a movement is detected, then the aimer turns on to
read the bar code.
There are 2 types: Normal or Enhanced.
Streaming Presentation—Normal: Fast scan speed, limited
reading range.
Streaming Presentation Mode—Normal
Streaming Presentation—Enhanced: Fastest possible scan
speed, slightly less reading range than Normal Streaming Pre-
sentation mode.
Streaming Presentation—Enhanced
Reset Factory Defaults
The following bar code resets factory defaults.

12
Mechanical Dimensions
Units are in millimeters. Tolerances: ±0.5 mm.
55
48
28
13.2
14
24.4
8.8
9.8
USB cable

13
Mounting Holes
Use M3 screws with a maximum depth of 5.8 mm/0.23 in. Max
torque 4.5kgf.cm/3.9 lbf.in and pull out resistance 736N.
Units are in millimeters. Tolerances ±0.5 mm.
20
30.5
4
48
12.5 31
30
13.5
13
420
15
17
4.5
42.5
4
447

14
Recommendations
• Do not add an exit window over the existing exit window.
• For best beeper performance, do not fully cover the beeper
opening.
• Be sure the cable is fitted tightly in the connector using the
cable slider. The cable over mold should not be more than
23 mm/0.90 in.
Technical Specifications
Mechanical
Dimensions 28 mm x 55 mm x 48 mm
(1.10 in x 2.17 in x 1.89 in])
Weight 50 g ±5 g
Interface USB 2.0
Electrical
Input Voltage 5 VDC ±0.25V
Standby Current 110 mA
Operating Current 220 mA
Environmental
Operating Temperature -30°C to 60°C /-22°F to 140°F

15
Storage Temperature -40°C to 85°C / -40°F to 185°F
Humidity 5% to 95% RH, non-condensing
Scanning Performance
Sensor Global Shutter
Resolution 640 x 480
Illumination White LED Illumination
Aimer 625 nm visible red LED
Motion Tolerance 6 m/s max
Field of View Horizontal = 40° ±1°
Vertical = 30° ±1°
Scan Angle Pitch = ±50°
Skew = ±50°
Tilt = 360°
Print Contrast 20%
Environmental

16
Reading Distances
• Measured from the front center of the housing
• 25°C, 200 lux for typical, 0 lux for guaranteed
•Photographicbarcodes
• Serial Trigger mode
Typical
Guaranteed
Symbology Near Far
13 mil UPC-A 4.3 cm / 1.7 in 38.5 cm / 15.2 in
10 mil Code 39 3.3 cm / 1.3 in 35.5 cm / 14 in
20 mil Code 39 6.8 cm / 2.7 in 74.2 cm / 29.2 in
20 mil QR Code 3.3 cm / 1.3 in 36.2 cm / 14.3 in
Symbology Near Far
13 mil UPC-A 4.7 cm / 1.9 in 37 cm / 14.6 in
10 mil Code 39 4.0 cm / 1.6 in 33.8 cm / 13.3 in
20 mil Code 39 7.2 cm / 2.8 in 68.3 cm / 26.9 in
20 mil QR Code 4.2 cm / 1.7 in 34.2 cm / 13.5 in

17
Customer Support and Technical Assistance
For customer support, contact your local Honeywell Sales Representa-
tive or fill out the support form at sps.honeywell.com/us/en/contact-us.
Limited Warranty
For warranty information, go to sps.honeywell.com/us/en/support/
productivity/warranties.
Patents
For patent information, see sps.honeywell.com/us/en/support/patents.
Disclaimer
Honeywell International Inc. and its affiliates, subsidiaries, and other
entities forming part of Honeywell group (“HII”) reserves the right to
make changes in specifications and other information contained in this
document without prior notice, and the reader should in all cases con-
sult HII to determine whether any such changes have been made. The
information in this publication does not represent a commitment on the
part of HII.
Honeywell warrants goods of its manufacture as being free of defective
materials and faulty workmanship during the applicable warranty
period. Honeywell’s standard product warranty applies unless agreed to
otherwise by Honeywell in writing; please refer to your order acknowl-
edgment or consult your local sales office for specific warranty details. If
warranted goods are returned to Honeywell during the period of cover-
age, Honeywell will repair or replace, at its option, without charge those
items that Honeywell, in its sole discretion, finds defective. The forego-
ing is buyer’s sole remedy and is in lieu of all other warranties,
expressed or implied, including those of merchantability and fitness
for a particular purpose. In no event shall Honeywell be liable for
consequential, special, or indirect damages. While Honeywell may
provide application assistance personally, through our literature and the
Honeywell web site, it is buyer’s sole responsibility to determine the suit-
ability of the product in the application. Specifications may change

18
without notice. The information we supply is believed to be accurate and
reliable as of this writing. However, Honeywell assumes no responsibility
for its use.
This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be pho-
tocopied, reproduced, or translated into another language without the
prior written consent of HII.
Copyright 2021 Honeywell International Inc. All rights reserved.
Web Address: sps.honeywell.com/us/en/products/sensing-and-iot
Other product names or marks mentioned in this document may be
trademarks or registered trademarks of other companies and are the
property of their respective owners.