Honeywell Voyager 1602g User manual

Voyager 1602g
Wireless Area-Imaging Pocket Scanner
User’s Guide

FrCvr-2
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this
document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been
made. The information in this publication does not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of
software and/or hardware to achieve intended results.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document
may be photocopied, reproduced, or translated into another language without the prior written consent of HII.
Copyright 2015 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
Microsoft® Windows®, Windows NT®, Windows 2000, Windows ME, Windows XP, and the Windows logo are trademarks or
registered trademarks of Microsoft Corporation.
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc.
Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies
and are the property of their respective owners.
For patent information, refer to www.hsmpats.com.

i
Customer Support
Technical Assistance ............................................................................................................ ix
Product Service and Repair .................................................................................................. ix
Limited Warranty ................................................................................................................... ix
Send Feedback ..................................................................................................................... ix
Chapter 1 - Getting Started
About This Manual ...............................................................................................................1-1
Unpacking Your Device .......................................................................................................1-1
Charging the Scanner Battery..............................................................................................1-1
Charging with a Power Supply.......................................................................................1-1
Charging with a PC ........................................................................................................1-2
Battery Charge Indicator ................................................................................................1-2
Pairing the Scanner with Bluetooth Devices ........................................................................1-2
Reading Techniques ............................................................................................................1-4
Menu Bar Code Security Settings........................................................................................1-5
Setting Custom Defaults ......................................................................................................1-5
Resetting the Custom Defaults ............................................................................................1-6
Chapter 2 - Programming the Interface
Introduction ..........................................................................................................................2-1
Keyboard Country Layout ....................................................................................................2-1
Keyboard Style.....................................................................................................................2-8
Keyboard Conversion ..........................................................................................................2-9
Control Character Output...................................................................................................2-10
Keyboard Modifiers ............................................................................................................2-10
Programming an Interface for an Access Point .................................................................2-12
Keyboard Wedge .........................................................................................................2-12
Laptop Direct Connect .................................................................................................2-12
RS232 Serial Port ........................................................................................................2-12
RS485 ..........................................................................................................................2-13
USB IBM SurePos........................................................................................................2-14
USB PC or Macintosh Keyboard..................................................................................2-14
USB HID.......................................................................................................................2-15
USB Serial....................................................................................................................2-15
Remote MasterMind™ for USB....................................................................................2-15
Gilbarco®Terminal Default Settings ............................................................................2-16
Honeywell Bioptic Aux Port Configuration....................................................................2-16
Datalogic™ Magellan®Aux Port Configuration............................................................2-16
NCR Bioptic Aux Port Configuration ............................................................................2-17
Wincor Nixdorf Terminal Default Settings ....................................................................2-17
Wincor Nixdorf Beetle™ Terminal Default Settings .....................................................2-17
Wincor Nixdorf RS232 Mode A ....................................................................................2-18
RS232 Modifiers...........................................................................................................2-18
Scanner to Bioptic Communication..............................................................................2-22
Table of Contents

ii
Programming the VG1602 Corded Interface.....................................................................2-23
Setting the VG1602 Corded Interface..........................................................................2-23
Corded USB PC or Macintosh Keyboard.....................................................................2-23
Corded USB HID POS................................................................................................. 2-23
Corded USB Serial ...................................................................................................... 2-24
Chapter 3 - Wireless System Operation
Bluetooth Settings ............................................................................................................... 3-1
Bluetooth HID Keyboard Disconnect ............................................................................. 3-1
Bluetooth Serial Port - PCs/Laptops.............................................................................. 3-1
PDAs/Mobility Systems Devices.................................................................................... 3-1
Changing the Scanner’s Bluetooth PIN Code................................................................3-1
Minimizing Bluetooth/ISM Band Network Activity................................................................ 3-2
Auto Reconnect Mode ................................................................................................... 3-2
Maximum Link Attempts ................................................................................................ 3-2
Relink Time-Out............................................................................................................. 3-3
Bluetooth/ISM Network Activity Examples..................................................................... 3-3
Communication Between the Scanner and the Host...........................................................3-4
Programming the Scanner and Host ................................................................................... 3-4
RF (Radio Frequency) Module Operation ...........................................................................3-4
System Conditions...............................................................................................................3-4
Scanner Is Out of Range ...............................................................................................3-4
Scanner Is Moved Back Into Range .............................................................................. 3-4
Out of Range and Back into Range with Batch Mode On..............................................3-4
About the Battery................................................................................................................. 3-5
Charging Information ..................................................................................................... 3-5
Battery Recommendations ............................................................................................ 3-5
Proper Disposal of the Battery.......................................................................................3-5
Beeper and LED Sequences and Meaning .........................................................................3-5
Scan LED Sequences and Meaning..............................................................................3-6
Low Battery Indicator.....................................................................................................3-6
Reset Scanner..................................................................................................................... 3-6
Scanner Report ................................................................................................................... 3-6
Scanner Address.................................................................................................................3-7
Linked Modes ...................................................................................................................... 3-7
Locked Link Mode - Single Scanner.............................................................................. 3-7
Open Link Mode - Single Scanner.................................................................................3-7
Unlinking the Scanner.................................................................................................... 3-7
Override Locked Scanner..............................................................................................3-8
Out-of-Range Alarm ............................................................................................................ 3-8
Alarm Sound Type.........................................................................................................3-8
Scanner Idle Alarm ..............................................................................................................3-9
Scanner Power Time-Out Timer.......................................................................................... 3-9
Flexible Power Management ............................................................................................. 3-10
Multiple Scanner Operation ............................................................................................... 3-10
Scanner Name................................................................................................................... 3-10
Application Work Groups................................................................................................... 3-12
Application Work Group Selection............................................................................... 3-12

iii
Resetting the Factory Defaults: All Application Work Groups ........................................... 3-13
Resetting the Custom Defaults: All Application Work Groups ........................................... 3-13
Access Point Operations ...................................................................................................3-13
Linking the Scanner to an Access Point ...................................................................... 3-13
Disconnect from Host and Connect to an Access Point .............................................. 3-14
Replacing a Linked Scanner........................................................................................3-14
Access Point LED Sequences and Meaning..................................................................... 3-15
Access Point Address........................................................................................................ 3-15
Paging ............................................................................................................................... 3-15
Paging Mode................................................................................................................ 3-15
Paging Pitch................................................................................................................. 3-15
Batch Mode ....................................................................................................................... 3-16
Batch Mode Beep ........................................................................................................ 3-17
Batch Mode Storage....................................................................................................3-17
Batch Mode Quantity ................................................................................................... 3-17
Batch Mode Output Order............................................................................................3-19
Total Records .............................................................................................................. 3-19
Delete Last Code.........................................................................................................3-20
Clear All Codes............................................................................................................3-20
Transmit Records to Host............................................................................................3-20
Batch Mode Transmit Delay ........................................................................................ 3-20
Host Acknowledgment....................................................................................................... 3-21
Host ACK Timeout.......................................................................................................3-22
Chapter 4 - Input/Output Settings
Programmable Button.......................................................................................................... 4-1
Virtual Keyboard ............................................................................................................ 4-1
Battery Charge Status ................................................................................................... 4-2
Flashlight Mode ............................................................................................................. 4-2
Bluetooth Pair/Unpair..................................................................................................... 4-3
Disable Programmable Button....................................................................................... 4-3
Power Up Beeper ................................................................................................................ 4-4
Beep on BEL Character.......................................................................................................4-4
Trigger Click ........................................................................................................................ 4-4
Good Read and Error Indicators..........................................................................................4-5
Beeper – Good Read.....................................................................................................4-5
Beeper Volume – Good Read........................................................................................ 4-5
Beeper Pitch – Good Read............................................................................................ 4-5
Beeper Pitch – Error ...................................................................................................... 4-6
Beeper Duration – Good Read ...................................................................................... 4-6
LED – Good Read ......................................................................................................... 4-6
Number of Beeps – Good Read .................................................................................... 4-7
Number of Beeps – Error............................................................................................... 4-7
Good Read Delay .......................................................................................................... 4-7
User-Specified Good Read Delay..................................................................................4-7
Manual Trigger Modes......................................................................................................... 4-8
Serial Trigger Mode.............................................................................................................4-8
Read Time-Out .............................................................................................................. 4-8

iv
Poor Quality Codes ............................................................................................................. 4-8
Poor Quality 1D Codes..................................................................................................4-8
Poor Quality PDF Codes ............................................................................................... 4-9
CodeGate®.......................................................................................................................... 4-9
Mobile Phone Read Mode...................................................................................................4-9
Character Activation Mode ................................................................................................ 4-10
Activation Character .................................................................................................... 4-10
End Character Activation After Good Read................................................................. 4-10
Character Activation Timeout ...................................................................................... 4-11
Character Deactivation Mode ............................................................................................ 4-11
Deactivation Character ................................................................................................ 4-11
Illumination Lights.............................................................................................................. 4-11
Aimer Delay ....................................................................................................................... 4-12
User-Specified Aimer Delay.........................................................................................4-12
Aimer Mode ....................................................................................................................... 4-12
Centering........................................................................................................................... 4-12
Preferred Symbology......................................................................................................... 4-14
High Priority Symbology .............................................................................................. 4-14
Low Priority Symbology ............................................................................................... 4-14
Preferred Symbology Time-out.................................................................................... 4-15
Preferred Symbology Default....................................................................................... 4-15
Output Sequence Overview............................................................................................... 4-15
Output Sequence Editor ..............................................................................................4-15
To Add an Output Sequence ....................................................................................... 4-15
Other Programming Selections.................................................................................... 4-16
Output Sequence Editor ..............................................................................................4-17
Partial Sequence ......................................................................................................... 4-17
Require Output Sequence ........................................................................................... 4-17
Multiple Symbols ............................................................................................................... 4-18
No Read ............................................................................................................................ 4-18
Video Reverse ...................................................................................................................4-19
Working Orientation........................................................................................................... 4-19
Chapter 5 - Data Editing
Prefix/Suffix Overview ......................................................................................................... 5-1
To Add a Prefix or Suffix:............................................................................................... 5-1
To Clear One or All Prefixes or Suffixes........................................................................5-2
To Add a Carriage Return Suffix to All Symbologies.....................................................5-2
Prefix Selections.................................................................................................................. 5-2
Suffix Selections.................................................................................................................. 5-2
Function Code Transmit ...................................................................................................... 5-3
Intercharacter, Interfunction, and Intermessage Delays......................................................5-3
Intercharacter Delay ...................................................................................................... 5-3
User Specified Intercharacter Delay..............................................................................5-3
Interfunction Delay......................................................................................................... 5-4
Intermessage Delay....................................................................................................... 5-4

v
Chapter 6 - Data Formatting
Data Format Editor Introduction ..........................................................................................6-1
Add a Data Format .............................................................................................................. 6-1
Other Programming Selections...................................................................................... 6-2
Terminal ID Table................................................................................................................ 6-3
Data Format Editor Commands........................................................................................... 6-3
Move Commands........................................................................................................... 6-5
Search Commands ........................................................................................................ 6-6
Miscellaneous Commands............................................................................................. 6-7
Data Formatter .................................................................................................................... 6-9
Data Format Non-Match Error Tone............................................................................6-10
Primary/Alternate Data Formats........................................................................................ 6-10
Single Scan Data Format Change............................................................................... 6-10
Chapter 7 - Symbologies
All Symbologies................................................................................................................... 7-1
Message Length Description ............................................................................................... 7-2
Codabar............................................................................................................................... 7-2
Codabar Concatenation................................................................................................. 7-3
Code 39 ............................................................................................................................... 7-4
Code 32 Pharmaceutical (PARAF)................................................................................ 7-5
Full ASCII....................................................................................................................... 7-6
Code 39 Code Page ...................................................................................................... 7-6
Interleaved 2 of 5................................................................................................................. 7-7
NEC 2 of 5...........................................................................................................................7-8
Code 93 ............................................................................................................................... 7-9
Code 93 Code Page ....................................................................................................7-10
Straight 2 of 5 Industrial (three-bar start/stop)................................................................... 7-11
Straight 2 of 5 IATA (two-bar start/stop)............................................................................ 7-12
Matrix 2 of 5....................................................................................................................... 7-13
Code 11 ............................................................................................................................. 7-14
Code 128........................................................................................................................... 7-15
ISBT 128 Concatenation.............................................................................................. 7-15
Code 128 Code Page ..................................................................................................7-16
GS1-128 ............................................................................................................................ 7-17
Telepen.............................................................................................................................. 7-18
UPC-A ............................................................................................................................... 7-19
UPC-A/EAN-13 with Extended Coupon Code...................................................................7-21
Coupon GS1 DataBar Output............................................................................................ 7-21
UPC-E0 ............................................................................................................................. 7-22
UPC-E1 ............................................................................................................................. 7-24
EAN/JAN-13 ......................................................................................................................7-24
Convert UPC-A to EAN-13 .......................................................................................... 7-24
ISBN Translate ............................................................................................................ 7-26
EAN/JAN-8 ........................................................................................................................ 7-27
MSI .................................................................................................................................... 7-29
GS1 DataBar Omnidirectional ........................................................................................... 7-31

vi
GS1 DataBar Limited......................................................................................................... 7-31
GS1 DataBar Expanded .................................................................................................... 7-32
Trioptic Code ..................................................................................................................... 7-32
Codablock A ...................................................................................................................... 7-33
Codablock F ...................................................................................................................... 7-34
Label Code ........................................................................................................................ 7-34
PDF417 ............................................................................................................................. 7-35
MacroPDF417 ................................................................................................................... 7-35
MicroPDF417.....................................................................................................................7-36
GS1 Composite Codes...................................................................................................... 7-36
UPC/EAN Version........................................................................................................ 7-37
GS1 Emulation .................................................................................................................. 7-37
TCIF Linked Code 39 (TLC39) ..........................................................................................7-38
QR Code............................................................................................................................ 7-38
QR Code Page ............................................................................................................ 7-39
Data Matrix ........................................................................................................................ 7-40
Data Matrix Code Page ...............................................................................................7-40
MaxiCode .......................................................................................................................... 7-41
Aztec Code ........................................................................................................................ 7-42
Aztec Code Page......................................................................................................... 7-42
Chinese Sensible (Han Xin) Code.....................................................................................7-43
Postal Codes - 2D ............................................................................................................. 7-44
Single 2D Postal Codes:.............................................................................................. 7-44
Combination 2D Postal Codes:.................................................................................... 7-45
Postal Codes - Linear........................................................................................................ 7-48
China Post (Hong Kong 2 of 5)....................................................................................7-48
Korea Post ................................................................................................................... 7-49
Chapter 8 - Interface Keys
Keyboard Function Relationships........................................................................................8-1
Supported Interface Keys .................................................................................................... 8-2
Chapter 9 - Utilities
To Add a Test Code I.D. Prefix to All Symbologies.............................................................9-1
Show Decoder Revision ...................................................................................................... 9-1
Show Scan Driver Revision ................................................................................................. 9-1
Show Software Revision...................................................................................................... 9-1
Show Data Format............................................................................................................... 9-1
Test Menu............................................................................................................................ 9-2
TotalFreedom ...................................................................................................................... 9-2
Application Plug-Ins (Apps) ................................................................................................. 9-2
EZConfig-Scanning Introduction.......................................................................................... 9-3
Installing EZConfig-Scanning from the Web.................................................................. 9-3
Resetting the Factory Defaults ............................................................................................ 9-4
Chapter 10 - Serial Programming Commands
Conventions....................................................................................................................... 10-1

vii
Menu Command Syntax .................................................................................................... 10-1
Query Commands ............................................................................................................. 10-1
Responses................................................................................................................... 10-2
Trigger Commands............................................................................................................ 10-3
Resetting the Custom Defaults.......................................................................................... 10-3
Menu Commands .............................................................................................................. 10-4
Chapter 11 - Product Specifications
Voyager 1602g Wireless Pocket Scanner Product Specifications .................................... 11-1
Standard Connector Pinout ...............................................................................................11-3
Micro-B USB ................................................................................................................ 11-3
Chapter 12 - Maintenance and Troubleshooting
Repairs .............................................................................................................................. 12-1
Maintenance ...................................................................................................................... 12-1
Cleaning the Scanner .................................................................................................. 12-1
Cleaning the Window................................................................................................... 12-1
Inspecting Cords and Connectors ............................................................................... 12-1
Replacing a Battery ........................................................................................................... 12-2
Troubleshooting.................................................................................................................12-3
Appendix A - Reference Charts
Symbology Charts ...............................................................................................................A-1
Linear Symbologies .......................................................................................................A-1
2D Symbologies.............................................................................................................A-2
Postal Symbologies .......................................................................................................A-2
ASCII Conversion Chart (Code Page 1252)........................................................................A-3
Lower ASCII Reference Table.............................................................................................A-4
ISO 2022/ISO 646 Character Replacements ......................................................................A-7
Keyboard Key Maps ..........................................................................................................A-10
Sample Symbols
Programming Chart

viii

ix
Customer Support
Technical Assistance
To search our knowledge base for a solution or to log in to the Technical Support portal and report a problem, go to
www.hsmcontactsupport.com.
For our latest contact information, see www.honeywellaidc.com/locations.
Product Service and Repair
Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain
warranty or non-warranty service, please visit www.honeywellaidc.com and select Support > Contact Service and Repair
to see your region's instructions on how to obtain a Return Material Authorization number (RMA #). You should do this prior
to returning the product.
Limited Warranty
Refer to www.honeywellaidc.com/warranty_information for your product’s warranty information.
Send Feedback
Your feedback is crucial to the continual improvement of our documentation. To provide feedback about this manual, con-
tact the Honeywell Technical Communications department at ACSHSMTechnicalCommunicatio[email protected].

x

1 - 1
1
Getting Started
About This Manual
This User’s Guide provides installation and programming instructions for the Voyager 1602g scanners. Product specifications,
dimensions, warranty, and customer support information are also included.
Note: The selections in this User’s Guide are dependent on the Voyager 1602g model you have purchased. PDF and 2
dimensional bar codes can only be read by model 1602g2D and cannot be read by model 1602g1D.
Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need
to change these settings, programming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an option indicates the default setting.
Unpacking Your Device
After you open the shipping carton containing the product, take the following steps:
• Check for damage during shipment. Report damage immediately to the carrier who delivered the carton.
• Make sure the items in the carton match your order.
• Save the shipping container for later storage or shipping.
Charging the Scanner Battery
The scanner’s battery must be fully charged before the first use. It can be charged using a power supply or by connecting the
USB cable to a computer. Refer to About the Battery on page 3-5 for further battery information.
Charging with a Power Supply
Connect the mini-USB connector to the scanner. Assemble the wall plug. Attach the plug to the USB connector, then plug
into an electrical outlet, as shown below.

1 - 2
Charging with a PC
Charging your scanner battery through the USB port of a computer will take longer than charging with an electrical outlet.
Connect the mini-USB connector to the scanner and the USB connector to the computer, as shown below.
Note: The mini-USB connector is only used for charging the scanner. If using a scanner in corded mode, it can also be
used to configure the device via EZConfig (see page 9-3 for further information).
Battery Charge Indicator
When the battery is charging, the small LED at the top left of the scanner flashes orange. When the battery is fully
charged, this LED is solid green. Refer to Scan LED Sequences and Meaning (page 3-6) and Low Battery Indicator (page
3-6) for the complete list of LED indications.
To use your scanner with a Honeywell Access Point (AP01-XXXBT), refer to Host ACK Responses, page 3-22 or Linking the
Scanner to an Access Point, page 3-13.
Pairing the Scanner with Bluetooth Devices
The scanner can be paired with Bluetooth devices such as personal computers, laptops, and tablets.

1 - 3
1. Scan the appropriate Bluetooth HID Keyboard Connect bar code below.
2. Set your personal computer, laptop, or tablet so it searches for other Bluetooth devices. (Refer to your device’s User’s Guide
for pairing instructions.)
3. Once your personal computer, laptop, or tablet has located the scanner, select the scanner name. Some personal
computers, laptops, or tablets will automatically pair with the scanner. If your device automatically pairs with the scanner, it
displays a successful pairing message and you do not need to continue to the next step.
4. If your personal computer, laptop, or tablet does not automatically pair with the scanner, a PIN is displayed. This PIN must
be scanned within 60 seconds. You must quickly scan Bluetooth PIN Code below, then scan the numeric bar code(s) for the
PIN code from the chart below, then scan the Save bar code.
Bluetooth HID Keyboard
Connect
Bluetooth HID Japanese
Keyboard Connect
Bluetooth PIN Code
0
1
2
3
4
5

1 - 4
Your personal computer, laptop, or tablet should now be paired with the scanner.
Once the scanner battery is charged and you have paired it, you may begin scanning bar codes. Verify the scanner operation
by scanning a bar code from the Sample Symbols in the back of this manual.
Reading Techniques
The Voyager 1602g has a large scan button just forward of a smaller, programmable button. (See Programmable Button on
page 4-1 for further information about the programmable button.)
6
7
8
9
Save
Scan button

1 - 5
Press the scan button to project an aiming beam. This beam should be centered over the bar code, but it can be positioned in
any direction for a good read.
The aiming beam is smaller when the scanner is closer to the code and larger when it is farther from the code. Symbologies
with smaller bars or elements (mil size) should be read closer to the scanner. Symbologies with larger bars or elements (mil
size) should be read farther from the scanner. To read single or multiple symbols (on a page or on an object), hold the scanner
at an appropriate distance from the target, press the scan button, and center the aiming beam on the symbol. If the code being
scanned is highly reflective (e.g., laminated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted reflection.
Menu Bar Code Security Settings
Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want
to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Contact the nearest technical sup-
port office (see Technical Assistance on page -ix) for further information.
Setting Custom Defaults
You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults
bar code below before scanning the menu commands for your custom defaults. If a menu command requires scanning numeric
codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults. When you have
entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code.
Note: The Custom Defaults settings apply to all workgroups Scanning the Save Defaults bar code also causes both the
scanner and the host to perform a reset and become unlinked. You must relink (pair) the scanner to the host. See
Wireless System Operation beginning on page 3-1 for additional information.
Linear bar codes
with aiming beam 2D Matrix symbol
with aiming beam
Set Custom Defaults
Save Custom Defaults

1 - 6
You may have a series of custom settings and want to correct a single setting. To do so, just scan the new setting to overwrite
the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and decide
you want the beeper volume set to High, just scan the Set Custom Defaults bar code, then scan the Beeper Volume High
menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be
updated.
Resetting the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This is
the recommended default bar code for most users. It resets the scanner to the custom default settings. If there are no custom
defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom
defaults will be defaulted to the factory default settings.
Note: The Custom Defaults settings apply to all workgroups Scanning the Save Defaults bar code also causes both the
scanner and the host to perform a reset and become unlinked. You must relink (pair) the scanner to the host. See
Wireless System Operation beginning on page 3-1 for additional information.
Activate Custom Defaults

2 - 1
2
Programming the Interface
Introduction
This chapter describes how to program your scanner for different keyboards and settings, and for an interface when using an
Access Point (see Programming an Interface for an Access Point, beginning on page 2-12). The VG1602g is primarily designed
as a cordless scanner. However, if you are using the VG1602g as a corded scanner, see Programming the VG1602 Corded
Interface beginning on page 2-23.
Keyboard Country Layout
If your interface is USB Keyboard or Keyboard Wedge through an Access Point, or a Bluetooth Keyboard, your keyboard layout
default is a US keyboard. To change this layout, refer to the chart below for your keyboard country. Scan the appropriate bar
code below to change the layout.
By default, national character replacements are used for the following characters: #$@[\]^‘{|}~ See ISO 2022/ISO 646
Character Replacements on page A-7 to view the character replacements for each country.
Keyboard Countries
* United States
Albania
Azeri (Cyrillic)
Azeri (Latin)
Belarus
Belgium
Bosnia
Brazil

2 - 2
Keyboard Countries (Continued)
Brazil (MS)
Bulgaria (Cyrillic)
Bulgaria (Latin)
Canada (French legacy)
Canada (French)
Canada (Multilingual)
Croatia
Czech
Czech (Programmers)
Czech (QWERTY)
Czech (QWERTZ)