Honeywell Voyager 9520 User manual

Voyager 9520/40
Eclipse 5145
Quick Start Guide
VG-ECL-QS Rev A
5/10
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Para Português, acesse www.honeywellaidc.com.br.
Перейти на русскоязычный сайт www.honeywellaidc.com.
日本語 : www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。
한글 www.honeywellaidc.com 로이동합니다 .

Getting Started
Turn off the computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Connecting the Scanner
USB:
Serial
(RS232):
Keyboard
Wedge:
optional adapter cable

Reading Techniques
Recall Defaults
The following bar code resets all standard product default settings.
Interface Selections
USB
³999998
Recall Defaults
³999970
³316400
USB Keyboard
Emulation
Load Integrated Full
Speed USB IBM/OEM
Defaults
³316460
USB Serial Emulation

Keyboard Wedge
Keyboard Country
Scan a bar code to select one of the following keyboard country
templates. Refer to your Configuration Guide for additional keyboard
country settings.
³ 5155143
Keyboard Wedge Emulation
³416210
³416220
United Kingdom
³416230
Germany/Austria
France
³416260
United States
³416200
Belgium
³416250
Spain
³416240
Italy

ALT Mode
If your bar code contains special characters from the extended ASCII
chart, for example, an e with an accent grave (è), scan the ALT Mode
On bar code. The data is then output with the special character(s).
Note: Scan ALT mode after scanning the appropriate Keyboard
Country code.
RS232 Communication Commands
³116217
ALT Mode On
³115816
RTS/CTS
Handshaking On
³115914
XON/XOFF On
³115913
ACK/NAK On
³116013
8 Data Bits
³116014
1 Stop Bit
³316045
No Parity

Prefix
Scan one of the following bar codes to program your scanner to add
or remove a start of text character, or AIM, NCR, or Nixdorf
identification characters before each bar code.
³116615
³116605
³107905
³107901
STX Prefix On
STX Prefix Off
³107915
AIM ID Prefix On
AIM ID Prefix Off
³107911
NCR Prefix On
NCR Prefix Off
³107907
³107917
Nixdorf Prefix On
Nixdorf Prefix Off

Suffix
Scan one of the following bar codes to program your scanner to add
or remove a carriage return, line feed, tab, or end of text after each
bar code.
³116613
³116603
³116604
CR Suffix On
CR Suffix Off
³116612
LF Suffix On
³116602
LF Suffix Off
³116610
Tab Suffix On
³116600
Tab Suffix Off
³116614
ETX Suffix On
ETX Suffix Off

User Configurable Prefix/Suffix
One or two prefix or suffix characters can be added and assigned for
data transmission. Use one of the codes below with a 3 code byte
sequence that represents the desired character (see ASCII
Conversion Chart, end of document) for your prefix or suffix. (To add
additional prefix/suffix characters, refer to your Single-Line
Configuration Guide.)
Scan the Enter/Exit Programming bar code to begin. Then scan
the 3 digit decimal equivalent of the ASCII character into the
appropriate character location with the code byte bar codes (see
Code Bytes, end of document). To save, scan the Enter/Exit
Programming bar code again.
Example: To add an asterisk (*) as a prefix, scan the bar codes:
1. Enter/Exit Programming
2. Configurable Prefix #1
3. Code Byte 0
4. Code Byte 4
5. Code Byte 2
6. Enter/Exit Programming
³904500
Configurable Suffix #1
³904600
Configurable Suffix #2
³903500
Configurable Prefix #1
³903600
Configurable Prefix #2
³999999
Enter/Exit Programming

Supplements
Scan one of the bar codes below to program your scanner for 2 or 5
digit bar code supplements.
977 (2 Digit) Supplement Required: Turn on this feature when a 2
digit supplement is required for EAN-13 codes that begin with 977.
³101217
2 Digit Supplements
On
³101207
2 Digit Supplements Off
³101216
5 Digit Supplements
On
³101206
5 Digit Supplements Off
³101314
977 Supplements On
³101304
977 Supplements Off

UPC/EAN Formatting
Scan Convert UPC-A to EAN-13 and a leading zero is transmitted
before a UPC-A bar code to convert it to EAN-13.
Scan Transmit Lead Zero on UPC-E to transmit a zero before each
UPC-E bar code.
Scan Transmit UPC-A Number System to transmit the UPC-A
leading digit with the bar code data. To transmit just the data, without
the leading digit, scan Don’t Transmit UPC-A Number System.
³107514
Convert UPC-A to
EAN-13
³107504
Don’t Convert UPC-A to
EAN-13
³107513
Transmit Lead Zero on
UPC-E
³107503
Don’t Transmit Lead
Zero on UPC-E
³107511
³107501
Don’t Transmit UPC-A
Number System
Transmit UPC-A
Number System