Honeywell Morley-IAS ZX Series Quick start guide

ZX Fire Alarm Control Panels MORLEY-IAS
ZX1Se
ZX2Se
Document No. 996-175-000-1, Revision 01
commissioning
manual
ZX5Se
ZX10Se
This manual should not be left with the end user

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page i
Table of Contents
1INTRODUCTION...................................................................................................1
1.1 NOTICE........................................................................................................................................1
1.2 WARNINGS AND CAUTIONS............................................................................................................1
1.3 NATIONAL APPROVALS..................................................................................................................2
1.4 EN54 INFORMATION.....................................................................................................................2
2USER CONTROL LEVELS...................................................................................4
2.1 LEVEL DEFINITION ........................................................................................................................4
2.2 USER PASSWORDS.......................................................................................................................4
2.3 LEVEL 3 PASSWORD.....................................................................................................................4
3CONTROLS AND DISPLAYS...............................................................................5
3.1 CONTROL KEYS ............................................................................................................................5
3.2 FRONT PANEL LED INDICATIONS ..................................................................................................6
3.3 ALPHANUMERIC DISPLAY INDICATIONS...........................................................................................8
3.3.1 Normal Condition................................................................................................................8
3.3.2 Display Examples – Fire Alarms.........................................................................................8
3.3.3 Display Examples – Faults..................................................................................................8
3.4 MEMORY LOCK.............................................................................................................................9
3.5 ENABLING LEVEL 2 OR LEVEL 3 ACCESS .....................................................................................10
3.5.1 Selecting the commissioning option .................................................................................10
3.6 OVERVIEW OF MENU STRUCTURE ...............................................................................................11
4COMMISSIONING A NEW INSTALLATION.......................................................13
4.1 STEP 1 – GENERAL SETUP .........................................................................................................13
4.2 STEP 2 – CONFIGURE EACH SIGNALLING LOOP ...........................................................................13
4.3 STEP 3 – CONFIGURE PERIPHERALS (IF REQUIRED).....................................................................13
4.4 STEP 4 – CONFIGURE OUTPUTS (SOUNDERS AND RELAYS)...........................................................13
4.5 STEP 5 – CONFIGURE DAY MODE OPERATION (IF REQUIRED).......................................................14
4.6 STEP 6 – CONFIGURE NETWORK OPTIONS (IF REQUIRED)............................................................14
4.7 STEP 7 – COMMENCE NORMAL OPERATION.................................................................................14
5CONFIGURE OPTION ........................................................................................15
5.1 ACCESSING THE CONFIGURE OPTION ..........................................................................................15
5.2 SIGNALLING LOOPS ....................................................................................................................15
5.2.1 Auto Learn ........................................................................................................................16
5.2.1.1 Full Auto Learn............................................................................................................................16
5.2.1.2 Quick Status Check ....................................................................................................................16
5.2.2 Calibrate............................................................................................................................17
5.2.3 Zones................................................................................................................................17
5.2.4 Devices .............................................................................................................................18
5.2.4.1 Changing Device Information......................................................................................................19
5.2.4.2 Location Text ..............................................................................................................................20
5.2.4.3 Device Events.............................................................................................................................21
5.2.4.4 Alarm Thresholds (Device Sensitivity) ........................................................................................21
5.2.4.5 Restoring Sensitivity Defaults .....................................................................................................22
5.2.4.6 Device Actions............................................................................................................................23
5.2.4.7 Class Change .............................................................................................................................24
5.2.4.8 Groups / Group Disablements ....................................................................................................25
5.2.4.8.1 Group Assignment.................................................................................................................25
5.2.4.8.2 Group Disablement Input.......................................................................................................25
5.2.4.8.3 Operation...............................................................................................................................25
5.2.4.9 Apollo Ancillary Sounder Outputs ...............................................................................................25
5.2.4.10 Ancillary LED (Morley-IAS & System Sensor).............................................................................26
5.3 PERIPHERALS.............................................................................................................................27
5.3.1 Auto Learn ........................................................................................................................27
5.3.2 Calibrate............................................................................................................................28
5.3.3 Zones................................................................................................................................28

MORLEY-IAS ZX Fire Alarm Control Panels
Page ii Document No. 996-175-000-1, Revision 01 Commissioning Manual
5.3.4 Devices.............................................................................................................................28
5.3.4.1 Changing Device Information.....................................................................................................28
5.3.4.2 8-Way Input Units....................................................................................................................... 29
5.3.5 Remote Control ................................................................................................................29
5.3.5.1 Panel Status Outputs ................................................................................................................. 29
5.3.5.2 Simulating Control Keys............................................................................................................. 29
5.4 SOUNDERS................................................................................................................................30
5.4.1 Sounder Output Types.....................................................................................................30
5.4.2 Allocating Sounders .........................................................................................................30
5.4.2.1 Pattern ON ................................................................................................................................. 31
5.4.2.2 Pattern OFF................................................................................................................................ 31
5.4.2.3 Pattern DELAY........................................................................................................................... 31
5.4.2.4 Pattern PULSE........................................................................................................................... 32
5.4.2.5 Pattern DOUBLE KNOCK .......................................................................................................... 32
5.4.2.6 Pattern OFF-PULSE-ON............................................................................................................33
5.4.2.7 Pattern OFF-ON-ON .................................................................................................................. 33
5.4.2.8 Pattern PULSE-ON-ON.............................................................................................................. 34
5.4.3 Detector Loop Addressable Sounder Circuit Controller Units (SCC)...............................34
5.4.4 Peripheral Loop Addressable Sounder Circuit Controller Units.......................................34
5.4.5 Overriding Delays at Level 1............................................................................................35
5.4.6 Sounder Fault Monitoring.................................................................................................35
5.5 RELAYS.....................................................................................................................................36
5.5.1 Fault Relay .......................................................................................................................36
5.6 CONTROL KEYS DISABLE OPTION ...............................................................................................36
5.7 PC (REMOTE PROGRAMMING)....................................................................................................36
6INSPECT OPTION..............................................................................................36
7TIME / DATE OPTION ........................................................................................ 37
7.1 TIME / DATE ..............................................................................................................................37
7.2 SYSTEM (CLEAR MEMORY).........................................................................................................37
7.3 CRYSTAL...................................................................................................................................38
8PROGRAM INTEGRITY OPTION.......................................................................39
8.1 PROGRAM A PANEL FROM A PC USING THE ‘FIRE’ PROGRAM......................................................39
9POWER SUPPLIES OPTION .............................................................................40
10 PASSWORDS OPTION......................................................................................40
11 DAY MODE OPTION..........................................................................................42
11.1 DAY MODES ..............................................................................................................................42
11.2 DELAYED MODE.........................................................................................................................43
11.2.1 Commissioning Delayed Mode.........................................................................................43
11.3 SENSITIVITY MODE.....................................................................................................................44
11.3.1 Commissioning Sensitivity Mode...................................................................................... 45
11.4 VERIFICATION MODE..................................................................................................................45
11.4.1 Commissioning Verification Mode....................................................................................46
12 SETUP OPTION..................................................................................................47
12.1 EVENT LOG ...............................................................................................................................48
13 NETWORKS OPTION.........................................................................................49
13.1 PANEL NETWORKS.....................................................................................................................49
13.1.1 Network - Panel Network Address ...................................................................................49
13.1.2 Standard Network Settings for Shared Zones..................................................................49
13.2 PORT B PROTOCOLS .................................................................................................................50

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page iii
14 SYSTEM EVENTS OPTION................................................................................52
14.1 EVENT MODES ...........................................................................................................................52
14.1.1 General Events.................................................................................................................53
14.1.2 Event Logic.......................................................................................................................53
14.1.3 Define Event Outputs........................................................................................................54
15 NORMAL OPERATION.......................................................................................54
16 SUPPLEMENTARY INFORMATION ..................................................................55
16.1 LOCATING EARTH FAULTS...........................................................................................................55
16.2 OVERRIDING DELAYS ON INDIVIDUAL OUTPUTS ............................................................................56
16.3 OPTIONAL FEATURES (OPERATIONAL FEATURES WITH REQUIREMENTS).......................................56
16.3.1 Output to fire alarm devices:.............................................................................................56
16.3.2 Delays to Outputs: ............................................................................................................56
16.3.3 Coincidence Detection:.....................................................................................................56
16.3.4 Fault Signals from points: .................................................................................................57
16.3.5 Disablement of addressable points:..................................................................................57
16.3.6 Test Condition:..................................................................................................................57
16.3.7 Network Disablement / Enablement .................................................................................57
16.4 PRINTER SET-UP OPTIONS .........................................................................................................57
16.5 HOCHIKI MULTI-SENSOR SUPPORT..............................................................................................58
16.6 SYSTEM SENSOR/ MORLEY-IAS MULTI-SENSOR & LASER SUPPORT............................................58
16.6.1 System Sensor/ M-IAS Multi & Laser Diagnostics............................................................58
16.6.2 System Sensor/ M-IAS Multi-sensor & Laser detectors ...................................................59
Table of Figures
Figure 1 – ZX1Se /ZX2Se Controls and Displays....................................................................................5
Figure 2 – ZX5Se & ZX10Se Controls and Displays................................................................................5
Figure 3 – System Control LED Display...................................................................................................6
Figure 4 – Memory Lock Switch Location ................................................................................................9
Table of Tables
Table 1 – Control Key Functions..............................................................................................................5
Table 2 – Alphanumeric and Interactive Control Keys.............................................................................6
Table 3 – LED Functions..........................................................................................................................7
Table 4 – Menu Function Overview........................................................................................................12
Table 5 – Alarm Threshold Setting.........................................................................................................21
Table 6 – List of Device Actions.............................................................................................................24
Table 7 - Peripheral Relay Unit, remote control operation.....................................................................29
Table 8 - Peripheral 8-way Input card, remote control operation...........................................................29
Table 9 - PC Programming tool - software compatibility........................................................................39
Table 10 – Day Mode Options................................................................................................................42
Table 11 – Setup Options.......................................................................................................................48
Table 12 – Slave Panel Network Settings..............................................................................................49
Table 13 – Master Panel Network Settings............................................................................................50
Table 14 – Port B Protocol Settings .......................................................................................................51
Table 15 – General System Events........................................................................................................53

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page 1
1 Introduction
1.1 Notice
• The material and instructions covered in this manual have been carefully checked for accuracy and
are presumed to be correct. However, the manufacturer assumes no responsibility for inaccuracies
and reserves the right to modify and revise this document without notice.
• These instructions cover the programming of the Fire Alarm Control
Panel. Refer to the Installation Manual (P/N 996-174-000-X) for
details of how to install the system and refer to the User Manual
(P/N 996-182-000-X) for information on operation and use of the
panel.
• If System Sensor / Morley-IAS / Honeywell Multi-sensor or Laser devices are incorporated into your
installation, ensure that you have the current Universal Loop Driver card appropriate to the protocol
you are using. If you have any doubt as to the correct version to fit, please contact Technical Support.
• The ZX1Se, ZX2Se, ZX5Se and ZX10Se Fire Alarm Control Panels are 1, 1-2, 1-5 and 1-10 loop panels
for use with analogue addressable devices from the following detector manufacturers’ ranges:
Apollo
S90
Hochiki
Morley-IAS
Nittan
System Sensor
EN54
!
EN54-2
Nittan
The ZXSe Range of Fire Alarm Control Panels have not been
independently tested and certified as complying with the
requirements of EN54-2 when used with the Nittan range of
signalling devices.
If the Nittan loop driver card is installed, the LPCB logo MUST be
removed.
1.2 Warnings and Cautions
These instructions contain procedures to follow in order to avoid injury and damage to
equipment. It is assumed that the user of this manual has been suitably trained and is
familiar with the relevant regulations.
All equipment is to be operated in accordance with the appropriate standards applicable
For use with software
version 834 onwards

MORLEY-IAS ZX Fire Alarm Control Panels
Page 2 Document No. 996-175-000-1, Revision 01 Commissioning Manual
CAUTION: A Lithium Battery is used for Data Retention.
Replace only with the same or equivalent type. Contact the Service Organisation for
Replacement.
This symbol identifies that the panel uses a safety isolating mains transformer.
1.3 National Approvals
This equipment must be installed and operated in accordance with these instructions and the
appropriate national, regional and local regulations specific to the country and location of the
installation. Consult with the appropriate Authority Having Jurisdiction (AHJ) for confirmation of the
requirements.
1.4 EN54 Information
EN54
!
EN54-2 13.7
Maximum of 512
sensors / manual
call points per
panel.
• The ZX1Se, ZX2Se, ZX5Se and ZX10Se range of panels has many
features, which if used inappropriately, may contravene the
requirements of EN54. Where such a possibility may arise, a suitable
warning is given with brief details of the EN54 requirement and the
relevant section it pertains to. A typical EN54 non-compliance
warning is illustrated.
EN54
9
• This Fire Control Panel complies with the requirements of EN54-2/4 1997. In addition
to the basic requirements of EN54, the panel conforms to the following optional
functions.
Option EN54-2 Clause
Indication: Fault signals from points
Controls: Coincidence Detection
Delays of Actioning Outputs
Disablement of each address point.
Test condition
Outputs: Outputs to fire alarm devices
8.3
7.12
7.11
9.5
10
7.8
EN54
9
• The power supplies for the ZX1Se, ZX2Se, ZX5Se and ZX10Se range of panels
complies with the following clauses of EN54-4.
Power Supply Functions EN54-4 Clause
Derive power supply from main power source
Derive power supply from a standby battery source
Charge and monitor the standby battery source
Detect & signal power supply faults
5.1
5.2
5.3
5.4

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page 3
EN54
N/
A
• In addition to the functions required by EN54-2, the panel supports a number of
ancillary functions that are not required by EN54. These are outlined below:
Ancillary Function Manual Section
Day Mode Options: Sensitivity Mode &
Verification Mode 4.5, 11.3 & 11.4
Network Options: 4.6 & 13
Configure Peripherals 4.3 & 5.3
Device Events 5.2.4.3 & 14
Alarm Thresholds (Device Sensitivity) 5.2.4.4
Device actions 5.2.4.6
Groups & Group Disablement 5.2.4.8
Sounder Output Patterns 5.4.1
PC Remote Programming 5.7
Setup Options 12
Event Log 12.1
Printer Setup Options 16.4
Class Change Input 5.2.4.7
Group Disable Input 5.2.4.8
Ancillary Sounder Outputs (Panel software 826 & later) 5.2.4.9

MORLEY-IAS ZX Fire Alarm Control Panels
Page 4 Document No. 996-175-000-1, Revision 01 Commissioning Manual
2 User Control Levels
2.1 Level Definition
• The ZX1Se, ZX2Se, ZX5Se and ZX10Se Fire Alarm Control Panels have three user control levels.
• At all three levels, the LED Displays indicate the condition of the installation, the Zone LED Displays
indicate the location of any fire alarm or fault and the alphanumeric display gives more detailed fire
alarm or fault information.
• At USER LEVEL 1, all the displays are functional but the front panel control keys are inhibited.
• At USER LEVEL 2, all front panel controls are functional and some system operation parameters and
functions can be changed. User Level 2 is reached by entering a password from level 1.
• At USER LEVEL 3, all front panel controls are functional and full system configuration and
programming is possible. User Level 3 is reached by entering a password from either Level 1 or Level
2. User Level 3 is intended for use by the system installer / maintenance contractor.
2.2 User Passwords
• Up to ten USER LEVEL 2 passwords can be programmed into the panel.
• The USER LEVEL 2 passwords can be assigned / changed at Level 3 by the installer / maintenance
contractor. Level 2 passwords do not allow access to Level 3 functions.
The default Level 2 Password is 1234. This should be changed.
Caution: When changing the password DO NOT use ‘0’ as the first digit.
2.3 Level 3 Password
The Level 3 Password is 9898.

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page 5
3 Controls and Displays
3.1 Control keys
• The control panel has two groups of control keys.
• A bank of five keys contains the four system control keys: Sound Alarms, Silence / Resound, Mute,
Accept and System Reset.
• A bank of 17 keys contains interactive and alphanumeric keys.
A
0
3
6
9>
N
Q
T
W
P
S
V
Y
Z
O
R
U
X
D
H
K
G
J
B
1
4
7
E
C
2
5
8
F
I
L
M
<
1 2 3 4 5 6 7 8 9 1011121314151617181920
A
0
3
6
9>
N
Q
T
W
P
S
V
Y
Z
O
R
U
X
D
H
K
G
J
B
1
4
7
E
C
2
5
8
F
I
L
M
<
1
21
41
61
2
22
42
62
3
23
43
63
4
24
44
64
5
25
45
65
6
26
46
66
7
27
47
67
8
28
48
68
9
29
49
69
10
30
50
70
11
31
51
71
12
32
52
72
13
33
53
73
14
34
54
74
15
35
55
75
16
36
56
76
17
37
57
77
18
38
58
78
19
39
59
79
20
40
60
80
Figure 1 – ZX1Se /ZX2Se Controls and Displays Figure 2 – ZX5Se & ZX10Se Controls and Displays
Key Legend Symbol Function
Sound Alarms
Press to Turn on ALL Sounder Outputs (i.e. evacuate building
manually). NB: This will only function where EVAC (Evacuate
Enable) is Enabled in the Setup menu. The default state of EVAC is
Evacuate Enabled. If it has been disabled in a prior commissioning,
pressing this key will have no effect.
Silence /
Resound
Press to Turn off all activated sounders.
Press again to re-activate the sounders.
Mute Buzzer
Press to silence the internal buzzer.
Accept
Press to accept a Stage 1 Investigation Delay Alarm
System Reset
Press to cancel all alarm conditions and reset the panel.
Table 1 – Control Key Functions
• The alphanumeric keys normally function as a numeric keypad. During programming, these keys can
be toggled to Letter Keys by pressing the CHANGE key. This gives access to letters A-M. For access
to letters N-Z, press and hold the SHIFT key while pressing the appropriate letter key.
Alphanumeric Display
System Status LED
Display
Control Keys
Zone LED Display
Program / Interactive
Keys
Optional Zone LED
Display

MORLEY-IAS ZX Fire Alarm Control Panels
Page 6 Document No. 996-175-000-1, Revision 01 Commissioning Manual
Key Legend Symbol Function
0 to 9 Press to enter numbers 0-9 or letters A-J (N-W with Shift)
> Press to scroll through fire alarms or faults manually on the display or
letter K (X with Shift)
< Press to scroll back through fire alarms or faults manually on the
display or letter Z (Y with Shift)
Change
ZM
Press to change a display option (where allowed)
or letter M (Z with Shift)
Enter
Press to confirm entry of a multiple digit number
No
Press to answer No, or terminate a display option
Yes
Press to answer Yes, or step through a display option
Shift
Press to show user options on the display
Press, during programming, to allow entry of Letters N-Z
Table 2 – Alphanumeric and Interactive Control Keys
• The control keys are disabled at USER LEVEL 1. Pressing the SHIFT key will cause the display to
prompt for entry of the Level 2 password. The password must be entered to re-enable the control keys
at Level 2.
3.2 Front Panel LED Indications
• The Level 1 LED Indicators are divided
into two sections.
• The upper array of LED Indicators shows
the operational conditional of the panel
and the installation.
• The lower array of Zone LED indicators
shows the location of a fire alarm or fault.
• The standard Zone LED Indicators
provide identification for up to 20 zones.
On the ZX5Se and ZX10Se panels, this
can be extended by adding either a further
20 zones (to give a total of 40 zones) or a
further 60 zones (to give a total of 80
zones).
• The LED Indicators illuminate as red,
yellow or green to give a clear indication
of the panel status as follows:
FIR
E
FAUL
T
System / CPU Faul
t
A
cknowledge
d
Earth Faul
t
Disablemen
t
Tes
t
Sounder Faul
t
Delayed Mode
Relays Disable
d
Powe
r
Supply Faul
t
A
larms Silence
d
Sounders Disable
d
Figure 3 – System Control LED Display

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page 7
Indicator Colour Function How to Clear
FIRE Red The panel has detected a fire alarm
condition, or the ‘Sound Alarms’ key
has been pressed.
Identify and correct the condition
causing the alarm and then perform
a panel reset.
Fault Yellow The panel has detected a fault. Correct the condition causing the
fault and then perform a panel reset.
Acknowledged Yellow A fault or alarm has been
acknowledged and the internal
buzzer silenced.
Correct the condition causing alarm
or fault and then perform a manual
reset. NOTE: If another alarm or fault
occurs, the internal buzzer
automatically resounds.
Disablement Yellow Part of the system, either input or
output, has been disabled manually
by the user.
Re-enable the device or devices.
Refer to Disablement Function.
Test Yellow The system is in test mode. Zone
LED indicators show which zones
are being tested.
Cancel test when finished.
Sounder Fault Yellow This indicates a wiring fault with one
of the sounder output circuits. Correct the fault condition and then perform a panel reset.
Delayed Mode Yellow This indicates that the system is
operating with delays to the sounder
outputs and the delays are active (in
force).
The delays may be enabled or
disabled. Refer to Disablement
Function.
Relays Disabled Yellow The relay outputs have been
disabled. Refer to Disablement Function.
Earth Fault Yellow An earth connection fault has
occurred on a cable. Correct the fault condition and then perform a panel reset.
System / CPU Fault Yellow The CPU has reset or a system fault
has occurred. Correct the problem, if appropriate, and then perform a panel reset.
Sounders Disabled Yellow Some or all of the sounder1outputs
have been disabled. Refer to Disablement Function.
Alarms Silenced Yellow The sounder1outputs have been
silenced. Correct the alarm condition and then
perform a panel reset. NOTE: Press
SILENCE / RESOUND again to
reactivate the sounders. If a new
alarm occurs, the alarms will
resound.
Supply Fault Yellow There is a problem with the power
supply, battery or supply input. Correct the fault condition and then perform a panel reset.
Power Green STEADY: Indicates AC Power is
present. FLASHING: Indicates a loss
of AC Power.
See Supply Fault.
Zone FIRE Red FLASHING: The zone is in a fire
alarm condition. Correct the alarm condition and then perform a panel reset.
Zone Fault Yellow FLASHING: The zone contains faulty
devices.
STEADY: The zone is either disabled
or in test mode.
Correct the fault condition and then
perform a panel reset.
Re-enable devices or cancel test
mode.
Table 3 – LED Functions
1This includes loop-based sounders.

MORLEY-IAS ZX Fire Alarm Control Panels
Page 8 Document No. 996-175-000-1, Revision 01 Commissioning Manual
3.3 Alphanumeric Display Indications
• The alphanumeric liquid crystal display gives 160 characters of information on a 4-line display. The
display is illuminated to assist viewing under dim ambient light conditions. NOTE: Should the AC Mains
fail; the back lighting on the liquid crystal display will be turned off to conserve battery power.
• When the numeric keypad is not in use, the display will revert to automatically scrolling through any
fire alarm or fault conditions present on the panel. If there are no alarm or fault conditions, the display
will show the date and time.
• Pressing the SHIFT key will show a list of optional functions or prompt for the level 2 password.
[Panel ACTIVE Control Keys INHIBITED] [1]
Do you want to enable the control keys?
3.3.1 Normal Condition
03-Mar-2007 11.38
All devices are inside working limits
3.3.2 Display Examples – Fire Alarms
1 of 1 FIRE
ALARM RAISED FROM CONTROL PANEL
[Active] 1)Commission 2)Test 3)Time [1]
4)Enable 5)Disable 6)Print 7)View
1 of 1 FIRE
2 of 2 FIRE MCP L2 A002 [1]
< - Zone Text - > < - Device Text - >
3.3.3 Display Examples – Faults
1 of 1 [1]
OPEN CIRCUIT ON SOUNDER B
For service phone (telephone no.)
2 of 8 No reply L2 A001 [1]
< - Zone Text - > < - Device Text - >
For service phone (telephone no.)

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page 9
3.4 Memory Lock
• To make changes that affect the
configuration of the system, such as
adding detectors, the system
memory must first be unlocked.
• Open the enclosure door and move
the memory lock switch to the open
position.
• The Memory Lock Switch is located
on the CPU Board.
• The figure opposite shows the
interior of the ZX1Se and ZX2Se
Fire Alarm Control Panels. The
ZX5Se and ZX10Se Fire Alarm
Control Panels use the same CPU
Board and have a similar
arrangement.
ISOLATE
ELSEWHERE
F1: T 2A H 250V
N
L
EARTH
EARTH BATT MON
AC MON
+25V
A
UX
O/P RELAY1
RELAY 1 RELAY 2
RELAY2
SOUNDER
OUTPUTS
POWER
LIMITED
+24V 0V A- A+ B- B+
COM COM N/C N/C N/O N/O
Printer Port
Port A:
Programming / Printer
Header Memory Lock
Figure 4 – Memory Lock Switch Location
Ensure that the Memory Lock Switch is in the open position prior to performing any
programming.
Ensure that the Memory Lock Switch is in the lock position before returning the panel to
normal operation (wait for prompt on display).

MORLEY-IAS ZX Fire Alarm Control Panels
Page 10 Document No. 996-175-000-1, Revision 01 Commissioning Manual
3.5 Enabling Level 2 or Level 3 Access
• To enable Level 2 or Level 3 operation, press the SHIFT key. The display will then show:
03-Mar-2007 11.38
All devices are inside working limits
[Panel ACTIVE Control Keys INHIBITED] [1]
Do you want to enable the control keys?
• Press the ‘Yes’ key and the display will prompt for entry of the password.
03-Mar-2007 11.38
All devices are inside working limits
[Panel ACTIVE Control Keys INHIBITED] [1]
Please Enter Password
• Enter the 4-digit, Level 2 password. The display then shows the Main Menu of user options.
[ Keypad available for user access ]
----------------------------------------------
[ACTIVE] 1)Commission 2)Test 3)Time [1]
4)Enable 5)Disable 6)Print 7)View
• If a key has not been pressed for a certain period, the display will revert to the normal Level 1 display
showing the system status message. To re-show the menu display, press the ’SHIFT’ key.
• If a key has not been pressed for a specified period of time, (normally 5-minutes – programmable),
then ‘Level 2’ access will be automatically cancelled. It will be necessary to re-enter the password to
re-activate Level 2 functions.
Note: As a commissioning aid the level 2 automatic timeout can be disabled at access level 3
(refer to Section10 Passwords Option). Leaving the panel in this state is not recommended
and must only be done with the written agreement of the local fire officer.
• For detailed information on the Level 2 user options, refer to the User Manual (P/N 996-182-000-X).
3.5.1 Selecting the commissioning option
• To access the commissioning functions in the panel, press ‘1’ to select the commission option.
• The display will prompt for entry of the Level 3 password. Enter the Level 3 password using the
numeric keys.
• The display will then show the commissioning menu options.

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page 11
3.6 Overview of Menu Structure
• The commissioning menu options are presented in three different screens (Pages). When the
commissioning menu option is selected, the display will show:
PAGE 1
03-Mar-2007 11.38
All devices are inside working limits
1)CONFIGURE YES)More Options [1]
2)Inspect 3)NORMAL OPERATION
• To move between the three commissioning screens, press the ‘Yes’ key.
PAGE 2
03-Mar-2007 11.38
All devices are inside working limits
1)Time/Date 2)Program Integrity [1]
3)Power Supplies 4)Passwords
PAGE 3
03-Mar-2007 11.38
All devices are inside working limits
1)Day Modes 2)Setup Options 3)Network [1]
4)Events
Page Option Function
Configure To configure the connection and operation of the signalling loop devices,
peripheral devices, sounder circuits and relay outputs.
Also provides configuration for upload / download of configuration data from
a PC.
Inspect Provides the same functionality as the configure option but with view only.
This allows the data to be inspected without risking any inadvertent changes.
1
Normal Operation To return the panel to normal operation – Level 2.
Time / Date To allow the date and time and other clock functions to be changed.
Also allows the system memory to be cleared to return the panel back to
factory default settings.
Program Integrity To show the version of the software installed in the panel.
To show the status of the operating program and configuration memory.
Power Supplies Shows the current state of the AC Mains and Battery supply conditions.
2
Passwords To define the number of User Level 2 passwords.
To define the value of each Level 2 password.
To define the maximum time the panel will remain at Level 2, without any key
pressed, before inhibiting the keys and returning to Level 1 operation.

MORLEY-IAS ZX Fire Alarm Control Panels
Page 12 Document No. 996-175-000-1, Revision 01 Commissioning Manual
Day Modes To define which, if any, of the following day modes are in operation.
Delayed Mode
Sensitivity Mode
Verification Mode
To define the effective times of operation, (i.e. start and finish).
Setup Options To define system setup parameters.
Network To define and configure the operation of the panel in a networked system.
3
Events To define system events that provide a more flexible cause and event
function than that available from standard zone-based,0 ringing options.
Table 4 – Menu Function Overview

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page 13
4 Commissioning a New Installation
• This section provides a guide to the steps that are required to commission a new installation.
• Precise details on how to perform each step, and on the functionality of each programming option, are
given in appropriate sections of this manual.
4.1 Step 1 – General Setup
• Ensure that the panel configuration memory is cleared and returned to factory settings. Refer to Time /
Date – System on Page 2 of the Commissioning Menus.
• Select the ‘Setup options’ from Page 3 of the Commissioning Menus. Press ‘Yes’ to step through each
item to inspect the factory default settings and to make changes as required. For example, to enter
service telephone number and company name.
4.2 Step 2 – Configure Each Signalling Loop
• Select the CONFIGURE option from Page 1 of the Commission Menus and then perform the
following.
1. Select ‘Signalling Loop 1’.
2. Perform an ‘Auto Learn’
3. Select ‘Devices’ and change sensor location text as required.
4. Assign Zones.
• Repeat actions 1-4 above for each signalling loop connected to the panel.
• Enter Zone descriptions.
NOTE:
1. If using a PC to program the panel, actions 3 and 4 above will already have been defined on the PC.
2. When using ZX panel software version 826, or later, and the Apollo
protocol with ancillary sounders fitted, refer to Section 5.2.4.9.
3. When using ZX panel software version 834, or later, and Morley-IAS or
System Sensor protocol with ancillary LEDs fitted, refer to Section
5.2.4.10.
4.3 Step 3 – Configure Peripherals (if required)
• Select the CONFIGURE option from page 1 of the Commission Menus and then perform the following.
1. Select ‘Peripheral’.
2. Perform an ‘Auto Learn’.
3. Select ‘Devices’ and change each unit’s location text as required.
4. Assign Zones and set the operation of the unit.
4.4 Step 4 – Configure Outputs (sounders and relays)
• Select the CONFIGURE option from page 1 of the Commission Menus and then perform the following.
1. Select ‘Sounders’, if zoned ringing patterns are required and program accordingly.
2. Select ‘Relays’, if zoned operation is required and program accordingly.
For use with software
version 826 onwards
For use with software
version 834 onwards

MORLEY-IAS ZX Fire Alarm Control Panels
Page 14 Document No. 996-175-000-1, Revision 01 Commissioning Manual
• Finally, select the INSPECT option from page 1 of the Commission Menus. Compare the
commissioning data entered against the installation sheets. This facility allows the data to be
inspected without risking any inadvertent changes.
4.5 Step 5 – Configure Day Mode Operation (If required)
EN54
!
EN54-2 7.11
Delays to Outputs
• Select the DAY MODES option from Page 3 of the
Commission Menus and then perform the following.
1. Select ‘Delayed Mode’, if the sounders and outputs are to be
delayed. (NOTE: Must be enabled at Level 2 to activate).
2. Select ‘Sensitivity Mode’, if the detectors are to have different
pre-alarm and fire alarm settings during day / night.
3. Select ‘Verification Mode’, if the analogue signals are to be
verified before the panel registers a fire alarm.
• Program the required mode as required.
4.6 Step 6 – Configure Network Options (If required)
• Select the ‘NETWORK’ option from page 3 of the Commission Menus. Press ‘Yes’ to step through
each item to inspect the factory default settings and change as required. For example, panel address,
number of slave panels, etc.
4.7 Step 7 – Commence Normal Operation
• Before finally commencing normal operation, perform the following.
1. Select ‘PASSWORDS’ from page 2 of the Commission Menus. Set the number of Level 2 passwords
and define the value of each password.
2. Select ‘PROGRAM INTEGRITY’ from page 2 of the Commission Menus. Check and record the
program checksums.
• Select ‘NORMAL OPERATION’ from page 1 of the Commission Menus.
Remember to lock the memory!!!

ZX Fire Alarm Control Panels MORLEY-IAS
Commissioning Manual Document No. 996-175-000-1, Revision 01 Page 15
5 Configure Option
5.1 Accessing the Configure Option
• Page 1 of the Commission menu is shown below:
[ Panel in Commissioning mode ]
----------------------------------------------
1)CONFIGURE YES)More Options [1]
2)Inspect 3)NORMAL OPERATION
• The CONFIGURE option allows the Signalling Loops, peripherals, sounders and relays to be
programmed. It also enables the function to allow the panel to be programmed by a PC.
• Press ‘1’ to select the ‘CONFIGURE’ option.
The CONFIGURE option and all sub menu options require the Memory Lock to
be open.
• The display then shows a menu of options as follows:
[ Panel in Commissioning mode ]
----------------------------------------------
CONFIGURE : Loop 1) 2) 3) 4) 5) [1]
6)Peripherals 7) Sounders 8)Relays 9)PC
NOTE:The menu will only show the number of signalling loops programmed during setup (Refer to the Setup
Option). The ZX2Se can only have two loops maximum.
5.2 Signalling Loops
• After selecting a loop from the configure menu, the display will present a list of options as follows:
[ Panel in Commissioning mode ]
----------------------------------------------
CONFIGURE : Loop 1) 1)Zones [1]
2)Devices 3)Auto Learn 4)Calibrate
The words ‘CONFIGURE: Loop 1’ on the top line of the menus provides a reminder that
panel is in configuration mode, with loop 1 selected.
• Select the required option by pressing the appropriate numeric key.
• When commissioning a new panel, start by performing an ‘Auto Learn’. This will cause the panel to
search for all devices installed on the loop.

MORLEY-IAS ZX Fire Alarm Control Panels
Page 16 Document No. 996-175-000-1, Revision 01 Commissioning Manual
5.2.1 Auto Learn
• This facility saves considerable time and effort when installing a system, or when changing sensor
configuration. It allows the system to learn for itself what devices have been installed on a particular loop.
• Press ‘3’ from the CONFIGURE menu to select ‘Auto Learn’. The display will respond with the message:
[ Panel in Commissioning mode ]
----------------------------------------------
Auto Learn finds ALL device addresses
and types on loop 1. Shall I do this ?
5.2.1.1 Full Auto Learn
• To proceed with ‘Auto Learn’, press the ‘Yes’ key. The system will confirm your command with the
message ‘Program running’ on the display. It may take several minutes to learn a complete loop. Each
possible sensor address is checked to see if any detector is installed at that address. If a detector has been
installed, the panel determines the type of the detector. If more than one detector is located at a single
address, or the detector type code is invalid, a warning message will appear on the display.
• Do not press any key until the display changes from the ‘program running’ message.
• Once the system has finished learning, it will respond with a display giving a summary of the detectors
found on the loop. For example.
[ Panel in Commissioning mode ]
---------------------------------------------
Ion Opto Temp Sounder MCP Zone-Mon Other
37 24 2 8 14 2 3
• This display should be checked, against the installation sheets, to ensure that the system has found
the correct number of devices.
• Pressing any key then restores the display to the normal commissioning menu.
• The Auto Learn sequence should be repeated for each loop on the system. It can be used as many times
as required and does not affect the text description used to describe the location of each sensor.
Always verify that the system has found all devices correctly. Use the ‘Devices’ option to
obtain detailed information on the device type and to see the address of each device
found on the loop.
5.2.1.2 Quick Status Check
• To perform a ‘Quick Status Check’, press the ‘No’ key instead when prompted to perform the Auto
Learn. The system will respond immediately with a display giving a summary of the detectors already
programmed for this loop. For example.
[ Panel in Commissioning mode ]
---------------------------------------------
Ion Opto Temp Sounder MCP Zone-Mon Other
37 24 2 8 14 2 3