Honeywell NOTIFIER ID62 Instruction sheet

ID61/62 installation,
commissioning &
configuration
manual
997-457-000-8, Issue 8 January 2010

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Contents
i 997-457-000-8, Issue 8
January 2010
Contents
1 Introduction 1
1.1 Manual Purpose 1
1.2 System Design and Planning 1
1.3 General 2
1.3.1 Date-dependent Functions 2
1.4 CE Marking 2
1.5 EN54 Functions 3
1.6 Ancillary Functions 4
1.7 Related Documents 5
1.8 Warnings and Cautions 5
1.9 Tips 5
1.10 Glossary of Icons 6
2 Installation Guide 7
2.1 How to Use this Section 7
2.2 Pre-Installation Check List 7
2.2.1 Some DO’s and DON’T’s 7
2.3 Transient Protection 8
2.4 Product Inspection 9
2.4.1 Checking Your Panel for Damage 9
2.4.2 What to do if Panel is Damaged or Suspect10
2.5 Dismantling the Panel 11
2.5.1 Removing the Cover(s) 11
2.5.2 Removing the Panel Electronics 12
2.5.3 Back Box Fixing 13
2.5.4 Flush Mounting Bezel (Optional) 14
2.6 Assembling the Panel 15
2.7 RS485 Communications Link 16
2.7.1 Fitting the RS485 Interface Module PCB 16
2.8 RS232 Interface Connections 17
3 Cabling 18
3.1 Cabling Instructions 18
3.1.1 Cable Terminations 19
3.2 Cable Installation Notes 20
3.2.1 Introduction 20
3.2.2 Quality of Cable and of Cable Installation 20

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Contents
ii997-457-000-8, Issue 8
January 2010
3.3 EMC Considerations 21
3.3.1 Screen Termination 21
3.3.2 Ferrite Sleeves (Optional) 21
3.4 MICC Cables 21
4 Commissioning 22
4.1 Introduction 22
4.2 Preliminary Checks 22
4.3 Internal Checks 23
4.3.1 Jumper Link Options 23
4.4 External Wiring Checks 24
4.4.1 Loop Wiring 24
4.4.2 RS485 Communications Link 25
4.4.3 DC Auxiliary Output 25
4.4.4 Sounder Circuit Outputs A and B 26
4.4.5 CFG Outputs C and D 27
4.4.6 -VE Outputs 28
4.4.7 Digital / ÜE Inputs 28
4.4.8 Switch Connections 28
4.5 Powering the Panel 29
4.5.1 Start-up Language Selection 29
4.5.2 Batteries 30
4.6 Configuration and Handover 31
4.7 Commissioning Tests 32
4.7.1 Test LEDs 32
4.7.2 Test LCD 32
4.7.3 Test Zones 32
4.7.4 Test Auto High Test 32
4.7.5 Test Outputs 32
4.7.6 Test Buzzer 32
4.7.7 Test Keyboard 32
4.8 Sensors and Modules 33
4.8.1 EN54 Requirements 33
4.8.2 Loop Wiring Testing 33
5 Configuration 35
5.1 Introduction 35
5.2 Navigation and Number Entry 35
5.3 Level 2 Configuration Options 35
5.4 Level 3 Configuration Options 36
5.5 Setup Options 37

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Contents
iii 997-457-000-8, Issue 8
January 2010
5.5.1 Panel Options 37
5.5.2 Site Details 43
5.5.3 Device Options 44
5.5.4 Peripheral Options 51
5.5.5 Day/Night Settings 59
5.6 Circuit Options 65
5.6.1 Signalling Line Circuit (SLC) - Devices 65
5.6.2 Signalling Line Circuit (SLC) - Learn 74
5.6.3 On-Board Circuits 77
5.7 Control-By-Event Output Rules 79
5.7.1 Output Type 82
5.7.2 Filter-by-type 83
5.7.3 Evacuation 84
5.7.4 Silence 84
5.7.5 Interrupt Delay 85
5.7.6 Class Change 85
5.7.7 Two Zone 86
5.7.8 Zones 87
5.7.9 Device Inputs 88
5.7.10 Soak Timer 89
5.8 Zone Texts 89
5.9 Access Options 90
5.10 System Options 92
5.10.1 Crystal Frequency 92
5.10.2 Wipe Memory 92
5.11 Normal 93
Appendix 1 - Specifications A1-1 to A1-6
Appendix 2 - ID61/62 Single Loop Panel
Differences A2-1 to A2-5
Appendix 3 - Fault Messages & Meanings A3-1 to A3-4
Appendix 4 - EN54-2 Options with
Requirements A4-1 to A4-4
Appendix 5 - Configuration of a Fault Routing
Output Using a Zone Monitor A5-1

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Introduction
1 997-457-000-8, Issue 8
January 2010
1 Introduction
1.1 Manual Purpose
The purpose of this manual is to provide the user with all
recommended procedures and full technical details for
the successful installation, commissioning and
programming of a NOTIFIER ID61/62 Series Panel.
Features of the ID61/62 Series fire control such as
VIEW™, Optiplex/SMART 2, SMART 3 and SMART 4
sensors, which require a fuller explanation of their
enhanced fire detection capabilities, are described in
Appendix 2 of this manual.
Procedures described in this manual include appropriate
warnings and cautions to guide the user towards adopting
safe and methodical work practices during the installation,
commissioning and programming phases.
The ID61/62 Series panels support OPAL protocol
devices. These devices support both OPAL and CLIP
loop polling protocols so they can be added to an existing
CLIP protocol loop. However, when OPAL protocol is
enabled on a loop a maximum of 10 CLIP devices
addresses can be supported as part of the total of 99
sensors and 99 modules.
Important Note
This manual must be read, and its content clearly
understood, before proceeding with any work relating to
the ID61/62 Series Panel. Damage to the control panel
may result from NOT following the recommended
procedures described in this manual.
This manual provides all necessary instructions for the ID61/
62 Series Panel and applies only to fire panels fitted with
compatible software.
CAUTION: In particular, care must be taken when
powering up/down any repeaters.
If there are any areas of doubt, consult your supplier
before continuing with the system installation,
commissioning and programming.
1.2 System Design and Planning
It is assumed that the system, of which the ID61/62 Series
Panel equipment is a part, has been designed by a
competent fire alarm system designer in accordance with
the requirements of EN 54 Part 14 and any other local
codes of practice that are applicable.
The design drawings should clearly show the positions
of all the ID61/62 Series Panel control equipment and
field devices.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Introduction
2997-457-000-8, Issue 8
January 2010
1.3 General
The ID61 and ID62 range of fire control panels is designed
for use with NOTIFIER’s range of addressable analogue
sensors, control and monitoring modules and addressable
call points. A unique signalling protocol is used, having
digital address and control signals and analogue pulse
width monitoring for the reply data from devices.
The serial communications interface operates under
RS485 protocol and enables communications between
the fire panel and repeaters.
While every effort is made to ensure the accuracy of the
content of this manual, the manufacturer reserves the
right to change the information without notice.
Installation
The ID61/62 Panel is easy to install providing the
recommended procedures described in this manual are
followed. To avoid inadvertent contamination of the PCB
Assembly, the manufacturer recommends it be installed
in the back box only after all other trades have completed
their tasks.
Commissioning
To commission the ID61/62 Panel, follow the recommended
procedures described in this manual. The manufacturer
recommends that during commissioning and maintenance,
ALL RS485 signal cables are disconnected at the Panel
end, BEFORE powering down the system and are
connected AFTER powering up the system.
Configuration
To configure the panel and system, carefully read and
follow the procedures given in this manual. These
procedures describe the menus that are displayed on
the Liquid Crystal Display (LCD) Unit.
Refer to the ID61/62 Series Operating Manual (ref: 997-
458-000-X) for a description of compatible addressable
Signalling Loop Circuit (SLC) analogue devices.
1.3.1 Date-dependent Functions
The calendar end date for this product is 31/12/2063
(two thousand and sixty three) and it will perform correctly
up to this date.
The calendar function has not been tested beyond
this date.
1.4 CE Marking
CE
This panel is CE Marked to show that it conforms to the
requirements of the following European Community
Directives
Only fit the electronics
module after all the other
trades have completed
their tasks!
Only suitably-qualified
engineers must install,
commission and
configure this product

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Introduction
3 997-457-000-8, Issue 8
January 2010
:The EMC Directive 2004/108/EEC, by the application of
the following EMC Standards:
EN 61000-6-3: Electromagnetic Compatibility (EMC)
Generic emission standard for Residential,
Commercial and Light industrial environments
EN 50130-4: EMC Product family standard: Immunity
requirements for components of fire, intruder and
social alarm systems.
Low Voltage Directive 2006/95/EEC, by the application
of the safety standard:.
EN 60950-1: Safety of information technology
equipment.
The Construction Products Directive 89/106/EEC, by the
application of the following standards:
EN 54-2:1998, (Amd. 1 & 2): Fire detection and fire
alarm systems - Control and indicating equipment.
EN 54-4: 1998 (Amd. 1 & 2): Fire detection and fire
alarm systems - Power supply equipment.
1.5 EN 54 Functions
This fire control panel is designed to comply with the
requirements of EN 54 Part 2/4. In addition to the basic
requirements of EN 54-2, the panel may be configured to
conform with the following optional functions - the applicable
clauses of EN 54-2 are referenced as follows:
Options Clause
Indications:
Fault signal from fire protection equipment 7.10.4
Recording of the number of entries
into fire alarm condition 7.13
Fault signals from points 8.3
Controls:
Delay to Outputs 7.11.1
Manual or automatic switching of delays to outputs 7.11.2
Dependency on more than one alarm signal, Type B 7.12.2
Disablement of each address point 9.5
Test condition 10
Outputs:
Fire alarm device(s) 7.8
Fire alarm routing equipment 7.9.1
Fire alarm routing equipment with alarm confimation 7.9.2
Automatic fire protection equipment: Type A 7.10.1
Automatic fire protection equipment: Type C 7.10.3
Fault warning routing equipment 8.9

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Introduction
4997-457-000-8, Issue 8
January 2010
The following features are provided by the Power Supply Unit
(PSU) of the ID61/62 Series Panel to comply with EN 54-4.
Features of the ID61/62 EN 54-4
Power Supply Unit (PSU) Clause
Derive power from the mains supply 5.1
Derive power from and monitor a
standby battery source 5.2
Derive power supply from and monitor a
standby battery source 5.3
Detect and signal various PSU faults 5.4
1.6 Ancillary Functions
The following is a list of ancillary functions that are provided
by the ID61/62 Series panel in addition to the those
required by EN 54-2/4. These functions are described in
the section of this manual as referenced (except those
marked thus ‘*’ which are described in 997-458-000-X,
ID61/62 Series Panel - Operating Manual):
Ancillary Manual
Functions Section Refs.
Site Specific Setup Options 5.5
Access Options 5.9
Voltage Indications *4.11.7
Control-by-Event 5.7
Output modes 5.7.1
Input type pattern 5.7.9
Disable/enablement *4.9
Repeater interface 2.7
Self-learn configuration - manual 5.6.1
Self-learn configuration - auto 5.6.2
Module supervision options 5.6.1
Module silence options 5.7.4
Text editing 5.8
Sensor LED blinking on/off 5.5.7
Bell pulsing ratio 5.5.8
Display of alarm count *4.11.6
Extend delay timer 5.5.3
Sounder Volt-free contact options 4.4.5
Relay drive output option 4.4.6
Extinguishing system features 5.5.3.7, 5.5.3.8, 5.5.3.9
5.7.1, 5.7.2, 5.7.10
CAUTION:
This product is not compliant
with EN 12094-1.
EN
12094-1
!
EN
12094-1
!
Fire extinguishing installations in
Europe are required to be certified as
compliant to this standard.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Introduction
5 997-457-000-8, Issue 8
January 2010
1.7 Related Documents
This manual only describes the installation,
commissioning and configuration of the ID61/62 Series
Panel. All operating functions are covered by the:
ID61/62 Series Panel Operating Manual (ref: 997-458-
000-X)
The Panel can support repeaters via the RS485
communications link. This manual does not provide
details about the repeaters or Compact Mimics; these
are described in:
IDR-2A, -2P & -6A Repeaters User Manual
(ref: 997-411-000-X).
IDR Mimic Installation and Commissioning Manual
(ref: 997-412-000-X).
Compact Mimic Installation Instructions (ref. 997-497-
000-X).
Note: The ‘000’ part of the manual reference is the UK
country code for the manual.
The ID51/52 Panel can also support the VIEWTM sensor.
This manual does not attempt to cover all the VIEWTM sensor
programming and calibration issues as these are described
in some detail in the following document, which is available
from NOTIFIER’s Technical Support Department:
VIEWTM Application Guide (ref: 997-198).
1.8 Warnings and Cautions
Where appropriate, the manual includes advisory
warnings and cautions to remind you to consider safety
at all times, especially when following the procedures
described herein.
You are alerted to any areas where high voltage [i.e. non-
Safety Extra-Low Voltage (SELV)] is present, or where
there may be a risk of damage to static-sensitive devices
if the recommended procedures described in this manual
are not followed.
An example of a high voltage warning and an anti-static
caution is provided to the left of this paragraph.
The ID61/62 Series Panel incorporates some features
which, if used inappropriately, may contravene the
requirements of EN 54. Where there is a possibility of
such an occurrence, a suitable warning is given with brief
details of the EN 54 requirement. A typical EN 54 non-
compliance warning is illustrated at left.
1.9 Tips
‘Handy tips’ are included, where appropriate, to assist
you in following quick and safe procedures for fire
detection system installation and integration.
Look for the ‘TIP!’ icon and supporting text, typically
illustrated at left.
Magnetise the tip of your
screwdriver to help when
offering small screws to
holes in confined spaces.
WARNING: High Voltage!
Take suitable precautions to
avoid electric shock.
EN 54-2:-8.8
One hardware-
configurable output
must be configured
as a fault relay.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Introduction
6997-457-000-8, Issue 8
January 2010
1.10 Glossary of Icons
Throughout this manual, and the other related ID61/62
Series Panel manuals, a number of icons are used either
as part of the illustrated process descriptions, or in the
main text to help clarify, or simplify, particular
configuration procedures.
The following icons are used to advise or indicate:
a. DO follow the recommended procedure or method.
b. DO NOT use this procedure or method.
c. Inspection of an item or sub-assembly is required at
this point.
d. Following a defined process meets/does not meet
the required approval/inspection criteria or standards.
e. Additional items to be considered.
f. This icon placed next to a pushbutton requires you to
press it while configuring the panel. Where two or
more icons are used, a number may be placed on or
near each hand to indicate the order of selection: 1
coming before 2.
g. Activity process step - flow arrow for single action or
iterative actions.
h. Leader arrow - used with activity processes.
i. Internal buzzer operating/not-operating or silenced.
j. Sounder operating/not-operating or silenced.
k. Power connected and switched ON/disconnected and
switched OFF.
l. Manual Call Point (MCP)/Sensor.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
7 997-457-000-8, Issue 8
January 2010
2 Installation Guide
2.1 How to Use this Section
This Installation Guide provides guidelines on how to
install an ID61/62 Series Panel quickly and safely.
For each stage in the panel installation and
commissioning procedures a brief description is given of
its purpose, complete with detail drawings, flow diagrams
and/or other graphics to make the instructions easy to
follow. Where required, procedures may be broken down
into one or more related diagrams, the number being
dependent upon the complexity of the defined task.
2.2 Pre-installation Check List
Before installing the ID61/62 Series Panel or fitting
sensors, you must first ensure that the following criteria
have been met. Failure to do this may not only result in
damage to the equipment, but may also cause problems
when commissioning the equipment or adversely affect
its performance.
2.2.1 Some Panel DO’s and DON’T’s
Before selecting a location for the ID51/52 Series Panel,
DO make sure that:
a. The operating ambient temperature is in the
recommended range:
+5oC to +35oCand
b. The relative humidity is between:
5% and 95%
c. The panel is wall mounted in a position which allows
clear visibility of displays and easy access to operating
controls. The height above floor level should be
chosen such that the LCD is just above normal eye
level (approximately 1.5 metres).

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
8997-457-000-8, Issue 8
January 2010
d. DO NOT locate the panel where it is exposed to high
levels of moisture.
e. DO NOT locate the panel where there are high levels
of vibration or shock.
f. DO NOT site the panel where there would be restricted
access to the internal equipment and cabling/wiring
connections.
2.3 Transient Protection
This equipment contains transient-protection devices.
Although no system is completely immune from lightning
transients and interference, for these devices to function
correctly, and to reduce susceptibility, this equipment
must be earthed correctly.
As with all solid state devices, this system may operate
erratically or can be damaged if subjected to lightning-
induced transients.
The use of overhead or outside aerial wiring is not
recommended due to the increased susceptibility to
nearby lightning strikes.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
9 997-457-000-8, Issue 8
January 2010
2.4 Product Inspection
The ID61/62 Series Fire Control Panels are relatively
simple to install providing the recommended procedures
described in this Installation Guide are followed.
Follow all installation instructions described in this
manual. These instructions must be understood and
the manufacturer’s recommendations followed to
avoid damage to the control panel and associated
equipment.
2.4.1 Checking Your Panel for Damage
It is important to check all supplied equipment for
damage before proceeding with the installation!
Before attempting to install your ID51/52 Series Panel,
you should do the following:
1After removing the panel, from its packing, and before
you proceed with installing it in its chosen location,
check for any damage that may have been caused
during transit.
Note: In the unlikely event that the panel supplied has
been damaged, you MUST NOT install it but return
it to your supplier. The procedure for returning faulty
items is described in Section 2.4.2, What to do if
Your Panel is Damaged or Suspect.
2If you are satisfied that the panel has NOT been
damaged you can now proceed with the installation
procedure. This manual addresses the recommended
installation methods of the panel. Refer to the relevant
sections that apply to your configuration requirements.
To prevent unnecessary damage to the electronic
components, the back box should be installed without
the electronics fitted. Refer to Sections 2.5.1 to 2.5.3
for details.
To avoid damage to the
control panel ensure that
you follow these
instructions
1
2

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
10997-457-000-8, Issue 8
January 2010
2.4.2What to do if Panel is Damaged or Suspect
If you have problems regarding the quality of any supplied
order items including the control panel, its ancillaries or
this manual or items are missing, follow the procedure
below:
1DO NOT continue with the installation but contact your
supplier for advice on what to do next.
Similarly, if the product is found to be faulty during
installation or while in use contact your supplier
immediately.
2To aid your supplier and the manufacturer, you are
requested to:
a. Quote the manufacturer’s unique batch reference
number which can be found on the packaging or
on the right-hand side of the electonics chassis.
b. With reference to PCB’s, quote the part number
and revision level which can be found along one
edge of the PCB - refer to the applicable section
of this manual for specific details.
c. Note all the details relevant to your complaint, date
of receipt, packaging condition, etc. and forward
this to your supplier.
3Where the product needs to be returned to your
supplier, you are requested to use the original
packaging, or suitable anti-static equivalent,
wherever possible.
0
0..9
3
12
46
7
5
[
98
12345678910 11 12 13 14 15 16
NNN - NNN
AAA AAAAA AAAAAAAAAAAAAAA
Serial Number:
nnnnnn / nn / nnnn / nnn
Thhshj iidjdhhh
Thhshj iidjdhhh
Adfddd jhjhgdjsfff iiiiojh
yudjdfh jfklrlkruuu uui
hjfjufhf jjjk k,kljk uu ulg
efjkfjkjk
Adfddd jhjhgdjsfff iiiiojh
yudjdfh jfklrlkr uuu uui
hjfjufhf jjjk k,kljk uu ulg
efjkfjkjk
1
2
3

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
11 997-457-000-8, Issue 8
January 2010
2.5 Dismantling the Panel
For installation purposes, it is recommended that the
cover(s) is(are) removed from the back box and stored
in a safe place until ready for commissioning.
If any other trades, e.g. plasterers or decorators, will be
working in the vicinity after fitting the ID61/62 Series Panel,
it is strongly recommended that before re-fitting the
cover(s) you remove the panel electronics and store in a
safe place until ready for commissioning. The main
components within the ID61/62 Series Panel are shown
below.
ID61/62 Series Panel Assembly
A Back box (ID61 or ID62)
B Chassis assembly
C Cover (ID61/62)
D Cover (ID62 only)
2.5.1 Removing the Cover(s)
To remove the ID61/62 Series Panel cover(s), it is
recommended that the following procedure is carried out
on a work bench BEFORE siting the panel on the wall:
1Use a 4mm hexagonal socket key to unscrew each
of the M6 screws.
2Carefully withdraw the cover away from the back box,
until the earth blade terminal within the cover (top right-
hand corner) is accessible.
3Carefully detach the shrouded earth lead spade
terminal from the earth blade terminal located on the
inner side wall of the cover.
Note: All blade connections to earth incorporate a locking
barb. To make a connection push the shrouded
receptacle on to the earth blade (1). To remove this
connection, pull the shroud (2), NOT the earth wire.
4Remove and store the cover(s) in a safe place.
The power supply ratings label (view ‘A’) is affixed to the
inside face of the fire control panel cover.
Before installing the back box, remove the panel
electronics (see Section 2.5.2, Panel Electronics).
A
B
C
D
‘A’
NOTIFIER
by Honeywell
NF30 ID51
ID52
ID61
ID62
NF50
NF30-S
NF50-S
230VAC, 50Hz, 1.6A
A

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
12997-457-000-8, Issue 8
January 2010
2.5.2 Removing the Panel Electronics
The ID61/62 Series Panel comprises a removable metal
chassis to which the following assemblies are fitted:
a. Main PSU PCB assembly (which also supports the
user interface fascia and LCD unit)
b. PSU3A assembly.
The Main PSU, user interface fascia/LCD are supplied
as one spared item (kit PN: 020-649). The PSU3A is
supplied as a separate spared item (kit PN: 020-648)
The combined assemblies are located within the back
box, but should ONLY be removed when installing the
back box or if any of the listed items above require
replacement.
CAUTION: The electronic circuits of the ID51/52 Series
Panel use CMOS devices which can be damaged by
static discharge. Suitable precautions MUST be taken
when handling circuit boards.
Procedure
When installing the back box (A), or if it becomes
necessary to remove the Main PCB (B) or PSU3A (C)
assemblies for another reason, follow this recommended
procedure:
1Remove the cover(s) and store in a safe place, see
Section 2.5.1, Removing the Cover(s). Then make
a back-up of the current system configuration,
remembering to disconnect the Earth Fault Monitoring
jumper link (D) at JP6 on the Main PCB.
Note: The earth connection to the cover fitted in back
boxes incorporates a locking barb (E). To remove
this connection, pull the shroud, NOT the earth
wire, from the earth blade terminal.
2When fitting any spared items listed above, isolate
the mains power supply and disconnect the battery
interlink wire.
3At the two-part connector J3, located on the left-hand
side of the bottom edge of the PSU PCB, use a
constant pulling action to disconnect the battery power
supply and thermistor wiring.
4At the PCB assembly, note the polarity and
connections of all cables and any jumper configuration
settings. Use a screwdriver to loosen all the connector
securing screws. Carefully secure all external cable
tails away from the electronics and from the back box.
5Using a cross-headed screwdriver, remove the eight
M3 x 10mm SEM screws from the PCB assembly.
Gently lift the PCB assembly clear of the supporting
pillars, place it in an anti-static bag and store safely.
Note: If the PCB is to be returned to the manufacturer
note its Serial Number and Revision Level (located
along one edge).
TEMPSNSR
+-
AE
1
D
JP6
E_FLT
JP6
E_FLT
CHGRINHN/C N/O COM
+-

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
13 997-457-000-8, Issue 8
January 2010
2.5.3 Back Box Fixing
The ID61/62 Series Panels are 133mm deep (PN: 020-
472-XXX) and 232mm (PN: 020-474-XXX) - external
dimensions including fixing dimples. Where required, the
deeper back boxes allow the fitting of high-capacity-rated
batteries as defined in Section 4.6.2 Batteries.
The back box must be fixed to the wall with screws at
three fixing locations (see drawing) using the procedure
given below.
The back box must only be installed when the panel
electronics have been removed (see Section 2.5.2,
Removing the Panel Electronics).
Wall Flatness
To prevent distortion, the back box MUST be installed on
the wall as flat as possible, i.e. with a maximum flatness
deviation between any two points of 3mm. Where the wall
is out of tolerance, use appropriate packing pieces when
installing the back box to meet the above requirements.
Failure to comply with this requirement will result in
the misalignment of the cover’s securing screws,
which may cause difficulties in fitting the cover.
Procedure
When a suitable location has been found for installing
the panel and the panel electronics have been removed,
fix the back box to the wall as follows:
1Using the centrally-positioned keyhole to temporarily
hold the back box in the required position on the wall,
mark the position of the fixing holes while ensuring
the panel is level.
2Using a suitable-sized drilling bit - for holes to take up
to 6mm (No. 12-sized) wood screws - drill the required
number of holes.
3Prepare apertures (20mm knockouts) required for
cable access.
4Secure the back box to the wall using all fixing holes
and appropriate-sized screws (up to 6mm
[No. 12-sized] round or pan-head screws - do not use
countersunk screws).
The number of screws required for either back box option
is shown at left and in the table below:
Back Box Part Number Screw Quantity
020-472-XXX 4
020-474-XXX 6
DO NOT use the back
box as a guide when
drilling.
All dimensions are in millimetres. Fixing
hole diameters are 6mm.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
14997-457-000-8, Issue 8
January 2010
2.5.4 Flush Mounting Bezel (Optional)
If flush mounting of the ID61/62 Series Panel is required,
a recess 110mm deep for the ID61 back box, or 208mm,
for the ID62 back box, and just large enough to
accommodate the back box must be cut in the wall (refer
to Section 2.5.3 Back Box Fixing for dimensions).
To fit the bezel:
1Before continuing, remove panel electronics and
batteries (if fitted) - see Section 2.5, Dismantling the
Panel.
2Offer the bezel (A), flat sideways towards you, to the
front of the back box (B) and position it so the bezel
front face (C) is lined up with the front face of the
back box shoulder (D).
3With the bezel held in position, use the slotted holes
(E) on the bezel side plates as guides to drill eight
3mm holes. Remove any swarf created.
4Secure the bezel using M3 self-tapping screws.
Note: The ID61/62 Series Panel back box must be fixed
to a solid vertical surface, or sub-frame inside the
recess, using its rear fixing holes. DO NOT rely
on the bezel as a means of fixing.
5Fit the back box with attached bezel to the wall recess
and re-assemble the panel, see Section 2.6
Assembling the Panel.
Before drilling the back
box, make sure that no
equipment is fitted.
All dimensions in millimetres

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
15 997-457-000-8, Issue 8
January 2010
2.6 Assembling the Panel
With the back box secured to the wall and all external cabling
ready for termination, assemble the panel as follows:
1Ensure that all power to the panel is isolated and
observe ALL safety and anti-static precautions when
installing the PCB assembly.
2Taking suitable anti-static precautions, offer the four slotted
holes of the chassis to the back box and, with it adequately
supported, connect the chassis earth lead to the earth blade
connectors in the back box.
3Locate the back box on the M4 SEM screws. Once in position,
use a cross-headed screwdriver to tighten the screws.
4Fit the labels. They may require the application of a
low tack adhesive:
i Apply low tack adhesive to hatched area indicated.
ii Slide each label into position.
iii Apply slight pressure to the area along the bottom
edge of the fascia to ensure the labels are secure.
5Insert the IEC mains plug into the socket on the top of
the PSU and apply mains power supply - then connect
the batteries. Check the PCB assembly operates
correctly and then isolate all power to the panel.
6At the Main PCB assembly:
i Noting the cable polarity, connect all cables and
secure at the correct termination blocks, see Cables
& Wiring below.
ii Set all required hardware jumper configurations,
refer to the Section 4 Commissioning.
7Fit the RS485 Interface Module PCB, if applicable, refer to
Section 2.7 RS485 Communications Link.
8Re-apply the mains power supply and then connect
the batteries.
9Disconnect the links at the earth fault monitoring jumper
E_FLT (JP6) and configuration lock MEM (JP7). Then
connect the RS232 9-way ‘D’ type Data Transfer Lead
(PN 082-173) to the panel at the RS232 socket
connector, SK3. Using the Support Tool, transmit the
latest system configuration to the panel.
10 Remove the lead and fit the links at JP6 and JP7, then
fit the cover.
Note: Connect the earth wire to the inner side wall of the
cover at the tag marked with the earth symbol.
Cables & Wiring
i ÜE/Sounder Output A and Sounder Output B (TB1)
ii CFG Outputs C and D (TB2)
iii Digital / ÜE Inputs (TB3)
iv 24 V Auxiliary Power Supply (TB4)
v Loop Cable Output/Input (TB5)
vi -VE Outputs (TB6)
vii Keyswitch
viii PSU Input (SK4, SK5)
ix FBF Communications Cable (TB9)
x FBF Power Supply (TB8)
xi RS232 Port (printer option)
xii RS485 Communications Cable (SK1).
0
0..9
3
12
46
7
5
[
98
12345678910 11 12 13 14 15 16
124-391 ID50+ PCB
CRYSTAL
FREQUENCY (XT2)
i
xi
xii
xix viii
viii
vii
ii iii iv vvi
1
1&5
1 & 5
2
7
TEMPSNSR
+-
4
JP6
E_FLT
JP6
E_FLT
JP7
MEM
JP7
MEM
9
9
8

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual
Installation Guide
16997-457-000-8, Issue 8
January 2010
2.7 RS485 Communications Link
The RS485 Interface PCB (PN: 124-247) enables the panel to
communicate with a maximum of sixteen (16) repeaters (active
IDR-2Aor passive IDR-2P) or mimic panels (IDR-M) (for further
details concerning the repeaters refer to 997-411, IDR-2A, -2P
& -6A Repeaters User Manual or 997-412, IDR Mimic
Installation and Commissioning Manual). The Isolated
RS485 PCB is located within a recess on the left-hand side of
the Main PCB. The PCB is fitted to the chassis using three
nylon snap-top spacers, provided with the Isolated RS485
Interface PCB Kit (PN: 020-479), and secured with a provided
M3 SEM screw to the metal spacer provided by the chassis.
To fit the Isolated RS485 Interface PCB follow the
instructions below.
Before starting, make sure you have a PC back-up of
the panel’s current configuration data.
Ensure you take appropriate anti-static precautions
before undertaking this procedure.
With the front cover(s) removed (see Section 2.5.1) and
ALL power disconnected, proceed as follows:
1Fit the nylon spacers (A) into the three provided holes
(B) in the chassis (C) - top right-hand position and both
bottom positions - by pushing them firmly into place until
they snap into position.
2Observing anti-static precautions, remove the RS485
Interface PCB from its packaging. If, after inspection,
no damage has occurred in transit and with it correctly
orientated, carefully offer the PCB to the three snap-
top spacers fitted in step 1. Working in a clockwise
direction, carefully push the PCB onto the snap-top
spacers (positions D) until the PCB is secure.
3Use the M3 x 8mm SEM screw (E) to secure the Isolated
RS485 PCB to the metal spacer (position F).
4Make all necessary wiring connections to the Isolated
RS485 Interface PCB - see details below.
5If the ID51/52 panel is NOT an end station, ensure the
jumper link is fitted in position JP1/2/4 (OFF) on the
Isolated RS485 PCB - this disconnects the line
terminating resistor. If the panel is an end station,
ensure the jumper link is fitted in position JP3/5/6 (ON).
With the IDR Series repeater, ensure the jumper link is
fitted as follows: an intermediate station - position JP1/
3/5 (TERM OFF); an end station - JP2/4/6 (TERM ON).
6If no other PCBs require fitting re-connect mains
power and the batteries and replace the front cover(s).
7To replace the Isolated RS485 Interface PCB, first reverse
the above procedure, steps 2 to 6, and then fit the
replacement RS485 Interface PCB using steps 2 to 6.
2.7.1 Cables and Wiring
8Make the following wiring connections to the Isolated
RS485 Interface PCB:
i Ribbon cable at socket SK2 from the Main PCB socket SK1.
ii Cable at socket SK1 from the next station on the
network (as applicable).
Make sure you
have a PC back-up
of the current
configuration data.
WARNING -
Disconnect ALL power
from the ID61/62 panel
when carrying out this
procedure.
ii
D
DD
i
F
124 - 247
S/No.
SK2
SK1
A
B
M1
JP1 JP3
JP2 JP5
JP4 JP6
F
B
C
Ax3
E
Upper Edge
Lower Edge
2
5
RS485 PCB - Part Number 124-247