Honeywell Notifier ID3000 Series User manual

fire panel
configuration tool
manual
ID2000
ID3000/
997-291 Version 3.05b November 2010

ID3000/ID2000FirePanelConfigurationToolManual
Contents
ii 997-291,Version 3.05
November2010
Quick Contents Reference by
Section
6 Networking
5 Time-of-Day
Programs
4 Control Matrix (CBE)
2 Panel Settings
3 Loop Devices
1 Introduction
CLICK HERE
FOR FULL
CONTENTS LIST
A
C
A
B
BC

ID3000/ID2000FirePanelConfigurationToolManual
Contents
iii 997-291, Version3.05
November2010
Contents
1 Introduction 1-1
1.1 PC Specification 1-2
1.2 Installation 1-2
1.3 Starting the Tool 1-3
1.3.1 AuthenticationOption 1-3
1.4 Connecting a PC to the Panel 1-4
1.5 Tool Overview and Menus 1-5
1.5.1 ToolLanguage Setting 1-5
1.5.2 ToolWindow 1-5
1.5.3 FileMenu 1-6
1.5.4 PanelMenu 1-7
1.5.5 RepeaterMenu 1-9
1.5.6 ViewMenu 1-12
1.5.7 EditMenu 1-12
1.5.8 CommunicationsMenu 1-14
1.5.9 SystemParameters Menu 1-17
1.5.10 ToolsMenu 1-19
1.5.11 External SystemsMenu 1-21
1.5.12 HelpMenu 1-22
1.5.13 Toolbar Options 1-22
1.5.14 LoopDisplay 1-23
Page

ID3000/ID2000FirePanelConfigurationToolManual
Contents
iv 997-291,Version 3.05
November2010
2 Panel Settings Configuration 2-1
2.1 Specification Tab 2-1
2.2 Loop Setting Tab 2-2
2.3 Port/Printer Options Tab 2-6
2.4 Pulse Options Tab 2-8
2.5 ÜE Configuration Tab 2-10
2.6 Remote Fire Outputs Tab 2-12
2.7 Tests Tab 2-14
2.8 Disablements Tab 2-15
2.9 Day/Night Mode Tab 2-18
2.10 Other Options Tab 2-20
2.11 Extinguishing System Tab 2-23
2.12 Alarm Coincidence Tab 2-24
2.13 VdS Network Options 2-25
3 Loop Devices Configuration 3-1
3.1 Select a Device 3-1
3.2 Edit Device 3-5
3.2.1 Sensors 3-5
3.2.2 Modules 3-16
3.2.3 DefineSounder Tone Slots 3-21
4 Control Matrix Configuration 4-1
4.1 Introduction 4-1
4.1.1 EN54Requirements 4-1

ID3000/ID2000FirePanelConfigurationToolManual
Contents
v 997-291,Version3.05
November2010
4.1.2 InputEvent Statement 4-2
4.1.3 OutputEvent Statement 4-5
4.1.4 ExtinguishingSystem Function 4-8
4.1.5 LogicOperations with Transfer
Flags 4-12
4.2 Review/Edit Control Matrix
Entries 4-16
4.2.1 ReviewEntries 4-16
4.2.2 Amend/Create/DeleteEntry 4-16
4.2.3 PrintMenu 4-17
4.2.4 ThermalAlarm Verification
Delay 4-17
4.3 Defining a Control Matrix Rule 4-18
4.3.1 InputEvent 4-18
4.3.2 OutputEvent 4-25
5 Time-of-day Configuration 5-1
5.1 Introduction 5-1
5.2 Manual Override 5-2
5.3 Editing Procedure 5-3
6 Network Configuration 6-1
6.1 Introduction 6-1
6.2 Master/Slave Network 6-2
6.2.1 Introduction 6-2

ID3000/ID2000FirePanelConfigurationToolManual
Contents
vi 997-291,Version 3.05
November2010
6.2.2 Procedure 6-4
6.3 ID2net Peer-to-Peer Network 6-8
6.3.1 Introduction 6-8
6.3.2 Procedure 6-11
6.3.3 SectorConfiguration 6-13
Appendix 1 Historic & Data Log Tool
Appendix 2 Database Query Utility
Appendix 3Additional Logic Example

ID3000/ID2000FirePanelConfigurationToolManual
Introduction
1 - 1 997-291,Version3.05
November2010
1 Introduction
The ID3000/ID2000 Fire Panel Configuration
Tool (PN: 020-558) allows the userto:
a. Configurepanel settings, loop devices,the
ControlMatrix and anetwork by usinga PC
remotefrom the fire panel.
b. Receivethe existing configuration from the
fire panel to the PC, and send a new or
edited configuration from the PC to the fire
panel.
c. Configure an IDR-6Arepeater.
ThroughoutthismanualtheID3000/ID2000Fire
Panel Configuration Tool is referred to as ‘the
Tool’ and the fire panel as ‘the panel’.
Be aware that...
Thismanualisnotintendedtobeafiredetection
system design guide and should only be used
by (or under the supervision of) a qualified
systemdesign engineer.
It is assumed that the system has been
designedin accordance with the requirements
of EN54 Part 14, BS 5839 Part 1:1988 and
otherlocalcodesofpracticethatareapplicable.
Some features of the panel may, if used
inappropriately,contravenetherequirementsof
EN54. This manual includes warnings (see
exampleopposite)wherethereisthepossibility
ofsuch an occurrence.
EN54-2:13.7
Maximumof512
Sensorsand/orMCPs
perpanelunless ELIBs
areused.
Cross-references(inbold
type)inthismanual
includelinks.For example,
click on (see Section 4)
togoto thatSection.

ID3000/ID2000FirePanelConfigurationToolManual
Introduction
1 - 2 997-291,Version3.05
November2010
1.1 PC Specification
The minimum specification for the PC is:
a. PentiumClass Processor.
b. Windows XP with service pack 2 with
128MBmemory.
c. 120MB disk space available.
d. CD-ROM.
e. SVGA 1024 x 768 colour display.
Note: To ensure that the Tool’s windows are
all displayed correctly, the PC’s Control
Panel/Display/Appearancetab/Scheme
option must be left at its default setting.
1.2 Installation
To install the Tool:
1TheCD should auto-run (if it does not, click
on‘Setup.exe’).
2Follow the on-screen prompts to complete
the process.

ID3000/ID2000FirePanelConfigurationToolManual
Introduction
1 - 3 997-291,Version3.05
November2010
1.3 Starting the Tool
Doone of:
a. Double-click on the Tool icon.
b. Select ‘Programs/Notifier/ID Series
ConfigurationTool’fromthePC’s‘Start’menu.
The Tool uses standard windows methods of
opening, closing, selecting etc.
1.3.1 Authentication Option
IftheToolis authenticated, upon firstcommuni-
cation with any panel using panel software
version4.21eoraboveanauthenticationcode
is sent to the panel. Subsequently, that panel
can only communicate with an authenticated
version of the Tool. If panel authentication is
not required, do not authenticate the Tool. To
authenticatetheTool:
1Note the customer code and send it to your
company’sauthorisedrepresentative.Onlythe
authorisedrepresentativemayapplyforthe
authenticationlicencekey.Thecustomercode
may be submitted (together with the other
requesteddata)usinganelectronicAuthentication
passcoderequest,availablebye-mailfrom:
[email protected]
2Notifier will e-mail the electronic passcode
request form back yo your company’s
authorised representative with the licence
key (valid for a specific PC only).
IftheToolislaterinstalledonadifferentphysical
driveor partition, orif a licence expiry warning
is displayed (given at 30 and 7 days), the
registrationprocedure mustbe repeated.
1
2
See ‘Help’ menu ‘About’ option for the current
authentication status of theTool.

ID3000/ID2000FirePanelConfigurationToolManual
Introduction
1 - 4 997-291,Version3.05
November2010
1.4 Connecting a PC to the Panel
Useasuitabledatacommunicationscable.The
panel requires a male RS232 9-way D-type
connectionfrom thecable.Toconnect the PC:
Caution: Direct connection of a PC to the panel’s
RS232 connector P1 will cause an earth
fault with potential damage to the PC.
Either use an isolated RS232 link or
(temporarily) disable the fault monitoring
circuit (steps 1 and 2 below). If an earth
fault already exists (LED next to link JP1
illuminated yellow), DO NOT connect
additional equipment likely to cause earth
faults as damage may result (i.e. inhibiting
the monitoring will not protect the
equipment).
1Disablethe earth fault monitoring circuit by
removing the jumper link on JP1 (A) at the
topright-hand corner ofthe Base PCB.The
PCB is marked ‘EFD’ above the link.
2Wait for at least one minute after disabling
thefaultmonitoringcircuit,thenusethedata
communications cable to connect the PC
tothe RS232 connectorP1 (B)on the Base
PCB.
3When the data transfer is complete (either
from panel to PC or PC to panel, see
Section 1.5.7),disconnect the PCfrom the
panel.
4Enable the earth fault monitoring circuit by
replacingthejumperonJP1.Tocomplywith
EN54-2: 8.2.4c,earthfaultmonitoringMUST
beenabled.
EN54-2:8.2.4c
EarthFaultMonitoring
isrequired.
Incorrectconnectionscould
resultin damagetothe
commsportofthePC.The
panel’sRS232connector
P1isNOTanisolatedport.