Honeywell Notifier FCM-1-REL User manual

WIRING
NOTE: All wiring must conform to applicable local codes, ordinances, and
regulations.
1. Install module wiring in accordance with the job drawings and appropri-
ate wiring diagrams.
2. Set the address on the module per job drawings.
3. Secure module to electrical box (supplied by installer), as shown in
Figure 2.
IMPORTANT: When using the FCM-1-REL for Class B applications, remove
Jumper (J1) and discard. The Jumper is located on the back as shown in
Figure 1B.
FIGURE 2. MODULE MOUNTING:
C1060-00
NO-460-002 1 I56-2992-004
FCM-1-REL Releasing Control Module
BEFORE INSTALLING
This information is included as a quick reference installation guide. Refer to
the control panel installation manual for detailed system information. If the
modules will be installed in an existing operational system, inform the opera-
tor and local authority that the system will be temporarily out of service. Dis-
connect power to the control panel before installing the modules.
NOTICE: This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
FCM-1-REL Releasing Control Modules are intended for use in intelligent, two-
wire systems, where the individual address of each module is selected using
the built-in rotary switches. This module is used to switch an external power
supply, which can be a DC power supply to a solenoid. It also supervises the
wiring to the connected load and reports the status to the panel as NORMAL,
OPEN, or SHORT CIRCUIT. The FCM-1-REL has two pairs of output termination
points available for fault-tolerant wiring and a panel-controlled LED indicator.
COMPATIBILITY REQUIREMENTS
To ensure proper operation, this module shall be connected to a compatible
Notifier system control panels only (list available from Notifier). In addition,
please refer to Notifier Device Compatibility document number 15378 for the
list of compatible solenoids.
MOUNTING
The FCM-1-REL mounts directly to 4-inch square electrical boxes (see Figure
2). The box must have a minimum depth of 21/8inches. Surface mounted elec-
trical boxes (SMB500) are available (for indoor dry applications only).
FIGURE 1A. CONTROLS AND FIGURE 1B. JUMPER LOCATION:
INDICATORS:
J1
C1059-00 C0910-00
I56-2992-004
SPECIFICATIONS
SLC
Normal Operating Voltage: 15 to 32 VDC Nominal
Average Operating Current: 700µA (LED flashing)
Maximum Activation Current: 9.0 mA (red LED on)
External Supply
Normal Operating Voltage: 24 VDC Nominal
Maximum Line Loss: 2.3 VDC (total allowable loss from power supply to module and from module to solenoid)
Minimum Operating Voltage to Activate Solenoid: 18 VDC (at solenoid)
Standby Current: 6.4 mA
Activation Current: 10 mA
Maximum Activation Current: 2 A
Solenoid
Supervisory Loop Voltage: 3.3 V
Supervisory Loop Current (Normal): 30 mA
Maximum Activation Current: 2 A
Temperature Range: 14°F to 140°F (-10°C to 60°C)
Humidity: 10% to 95% RH Non-condensing
Dimensions: 41/2˝ H × 4˝ W × 11/4˝ D; (106 mm H × 108 mm W × 31 mm D)
Accessories: Wall cover plate (included); SMB500 Surface Mount Electrical Box (for indoor dry applications only)
12 Clintonville Road
Northford, CT 06472-1653
Phone: [phone]
INSTALLATION AND MAINTENANCE INSTRUCTIONS

FIGURE 3. TYPICAL CLASS B, SOLENOID CONFIGURATION:
(+)
(-)
(+)
(-)
(+)
(-) (-)
(+)
24 VDC CIRCUIT
DO NOT LOOP WIRE ON TERMINALS 10 & 11. BREAK WIRE
RUN TO PROVIDE SUPERVISION OF CONNECTIONS.
TO NEXT
MODULE
24 VDC POWER SUPPLY
ISOLATED, REGULATED,
POWER LIMITED PER NFPA
70. UL 864 LISTED FOR
RELEASING DEVICE
SERVICE USE WITH
BATTERY BACKUP.
POWER SUPPLY
SUPERVISION BY
MODULE
CONNECT MODULES TO LISTED
COMPATIBLE NOTIFIER
CONTROL PANELS ONLY
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
ALL WIRING SHOWN IS SUPERVISED
AND POWER LIMITED
RELEASING
CONTROL
MODULE
FROM
PANEL OR
PREVIOUS
DEVICE
TO NEXT
DEVICE
OUTPUT TO A UL LISTED FIRE
ALARM RELEASING SOLENOID
(REFER TO PANEL MANUFACTURER'S
INSTALLATION DOCUMENT)
C0996-00
FIGURE 4. TYPICAL CLASS A, SOLENOID CONFIGURATION:
(+)
(–)
(+)
(–)
(+)
(–)
(+)
(–)
ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED
POWER SUPPLY
SUPERVISION BY
MODULE
TO NEXT
MODULE
TO NEXT
DEVICE
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
CONNECT MODULES TO
LISTED COMPATIBLE
NOTIFIER CONTROL
PANELS ONLY
FROM
PANEL OR
PREVIOUS
DEVICE
24 VDC CIRCUIT
DO NOT LOOP WIRE ON TERMINALS 10 & 11. BREAK WIRE
RUN TO PROVIDE SUPERVISION OF CONNECTIONS.
24 VDC POWER SUPPLY
ISOLATED, REGULATED,
POWER LIMITED PER
NFPA 70. UL 864 LISTED
FOR RELEASING DEVICE
SERVICE USE WITH
BATTERY BACKUP.
RELEASING
CONTROL
MODULE
OUTPUT TO A UL LISTED FIRE
ALARM RELEASING SOLENOID
(REFER TO PANEL MANUFACTURER'S
INSTALLATION DOCUMENT)
C0997-00
NO-460-002 2 I56-2992-004
©2008 Notifier