Honeywell Myers Park 51861 User manual

Myers Park Ceiling Fan
User Manual
Read and save these instructions before use
Home
Model #51861

EN I2
PACKAGE CONTENTS
HARDWARE CONTENTS
Mounting Bracket Screw (x4)
Mounting Bracket
Canopy
Downrod
Downrod Clip
Downrod Pin
Blade Arm (x5)
Blade (x5)
Yoke Cover
Set Screw (x 2) Yoke
Motor Assembly
Light Pan
Fitter Plate
Light Pan
Screw (x3)
Fitter Plate
Screw (x 3)
Light Kit
Bulb (x2)
Glass Bowl Remote Kit Blade Balancing Kit
36-Inch Lead Wire
Blade Screw (x15) Blade Washer (x15) Motor Screw (x10) Lead Wire
Wire Connector
Note: Some extra hardware may be included. The quantity listed above is the number required for installation.
Secondary Spring
Washer
Support Washer Push-in Connector
(x2)
Secondary Support Screw

EN I3
SAFETY INFORMATION
THANK YOU
Please read and understand this entire manual before attempting to assemble, operate or install the product.
• Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code and ANSI/NFPA 70-
199. Hire an electrician or consult a do-it-yourself handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum of 7 feet from the blades to the floor and at least 30 inches from
the tip of the blades to any obstruction.
• RATED FOR INDOOR USE. This fan is not suitable for damp or outdoor locations
• The weight of the fan is 18.81 pounds.
DANGER: When using an existing outlet box, make sure it is securely attached to the building structure and can support
the full weight of the fan. Failure to this can result in serious injury or death. The stability of the outlet box is essential in
minimizing wobble and noise in the fan after installation is complete.
WARNING: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
WARNING: Using a full-range dimmer switch to control fan speed will cause a humming sound from the fan. To reduce the
risk of fire or electric shock, do NOT use a full-range dimmer switch to control fan speed.
WARNING: To reduce the risk of fire, electric shock or personal injury, mount the fan to an outlet box marked
“ACCEPTABLE FOR FAN SUPPORT” and use the mounting screws provided with the outlet box. Most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt. Secure the outlet box directly to the building structure. The outlet box and its support must be able to
support the moving weight of the fan (at least 35 lbs.).
WARNING: To reduce the risk of fire, electric shock or personal injury, wire connectors provided with this fan are designed to
accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and/or there is
more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use.
WARNING: To reduce the risk of fire, electric shock or personal injury, do not bend the blade arms when installing them,
balancing the blades or cleaning the fan. Do not insert objects between the rotating fan blades.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts other than those
provided with this fan will void the warranty.
CAUTION: Be sure the outlet box is properly grounded or a ground (green or bare) wire is present.
CAUTION: Carefully check all screws, bolts, and nuts on the fan assembly ensure they are secured.
Honeywell Ceiling Fans feature a collection of fans in various sizes and specifications to ensure your choice of indoor or outdoor
fan delivers optimum performance for your room’s size. You can trust the quality of Honeywell Ceiling Fans to deliver maximum
airflow and stylish lighting options. Honeywell Ceiling Fans use high-quality materials that are long lasting and durable to
deliver a great look and last for years to come.

EN I4
CARE AND MAINTENANCE
At least twice each year, lower the canopy to check the downrod assembly and tighten all screws on the fan. Clean the motor
housing and blades with a soft brush or lint-free cloth to avoid scratching the finish.
Bulb Replacement: Use 60-watt max. B11, E26-base LED, CFL or incandescent bulbs. Halogen bulbs are not recommended for
this item.
Battery Replacement for Remote: Use CR2032 lithium batteries. Exhausted batteries should be removed from remote. Non-
rechargeable batteries should not be recharged. Do not dispose of batteries in fire, as they may explode or leak.
Important: Shut off the main power supply before you begin any maintenance task. Do NOT use water or a damp cloth to clean
the fan.
SAFETY INFORMATION
CAUTION: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device (if applicable).
CAN ICES-003 (B) / NMB-003 (B)
CAN ICES-005 (B) / NMB-005 (B)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Please note changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
HKC-US
3350 Players Club Parkway #225
Memphis, TN 38125
1-877-361-3883

EN I5
D
D
INITIAL INSTALLATION
PREPARATION
Before beginning the assembly of this product, ensure all parts are present. Compare all parts with the package contents list
and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated assembly time: 2 hours
Tools required (not included): Flat-head and Phillips Screwdriver, Safety Glasses, Step Ladder, Wire Cutters and Wire Strippers.
1. Turn off power to the fan at the breaker box and the wall switch (Figure 1.1). DANGER: Failure to disconnect the power supply
prior to installation may result in serious injury or death.
2. Choose one of the following mounting options (Figure 1.2) :
Standard Mount - best suited for ceilings 8 feet or higher. For very high ceilings, use a longer downrod (not included).
Angle Mount - best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to ensure proper blade
clearance. Ensure the ceiling angle is not steeper than 16 degrees.
Flushmount Installation - not available for this model.
Closemount Installation - not available for this model.
3. Ensure the blades will be at least 30 inches from any obstructions. Also check the downrod length to ensure the blades will be
at least 7 feet above the floor (Figure 1.3).
1. Loosen all four mounting bracket screws and completely remove the two screws from the round holes in the canopy. Save the
screws for later. Remove the canopy from the mounting bracket (Figure 2.1).
2. Install the mounting bracket to the outlet box (not included) using the screws and washers provided with the outlet box.
WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to the outlet box marked “acceptable for fan
support” and use the mounting screws and washers provided with the outlet box (Figure 2.2).
3. Discard the orange packing material from the top of the motor assembly (Figure 2.3).
Figure 1.1
Figure 2.1
Figure 1.2
Standard
Mount
Angle Mount
Orange Packing
Material
Figure 2.2
Figure 1.3
Figure 2.3
Standard Mount
Flushmount
Angle Mount
Closemount
Mounting
Bracket Screw
Canopy
7 feet
minimum
30 in.
minimum

EN I6
STANDARD OR ANGLE MOUNT INSTRUCTIONS
1. Remove the downrod clip and downrod pin from the downrod. Then partially loosen the set screws in the yoke at the top of
the motor assembly (Figure 3.1).
2. Insert the downrod through the canopy and yoke cover. Feed the wires and braided cable from the fan through the downrod.
Depending on the length of downrod you use, you may need to use the 36-inch lead wire to accomodate a 36 or 48-inch
downrod (sold separately). When necessary, connect the 3-pin connector extending from the center of the downrod to one
end of the 36-inch lead wire. Note: The downrod included with this fan will not utilize the 36-inch lead wire (Figure 3.2).
3. Slide the downrod into the yoke of the motor assembly, align the holes, then re-install the downrod pin and downrod clip.
Secure with the two set screws and slide the yoke cover down until it rests on top of the motor assembly (Figure 3.3).
4. Install the ball end of the downrod into the opening of the mounting bracket. Rotate the downrod until the tab in the
mounting bracket is seated in the slot in the downrod ball (Figure 3.4). WARNING: The fan and/or downrod should not rotate
in the mounting bracket, if installed correctly. Failure to align the slot in the downrod ball with the tab on the mounting
bracket may result in fan falling causing serious injury or death.
Figure 3.1
Downrod Clip
Mounting
Bracket
Downrod
Downrod
Downrod Pin
Set Screw
Downrod
Tab
Canopy
Slot
Yoke Cover
Figure 3.2 Figure 3.3
Figure 3.4
Set Screw
Downrod Clip
Downrod Pin
36” Lead Wire

EN I7
FINAL INSTALLATION
1. Use push-in connectors to connect the supply wires from outlet box to the lead wires according to the wiring diagram and the
following instructions (Figure 5.1):
• Push the White (neutral) supply wire and the white wire from lead wire into the the holes of one push-in connector.
• Push the Black (hot) supply wire and the black wire from lead wire into the the holes of one push-in connector.
WARNING: After the connections have been made, the connected wires should be turned upward and pushed carefully up
into the outlet box. Place the Black and White wire connections on opposite sides of the outlet box.
2. Connect the 3-pin connector extending from the downrod to the 3-pin connector on lead wire. Then, connect the green/bare
(ground) supply wire to the green wires from the downrod and the mounting bracket (Figure 5.2).
3. Raise the canopy, ensure the two mounting bracket screws are aligned with the J-shaped slots in the canopy. Then turn the canopy
in a clockwise direction until the mounting bracket screws are completely engaged in the J-shaped slots. Then, install the two
previously removed mounting bracket screws in the round holes. Securely tighten all mounting bracket screws (Figure 5.3).
Figure 5.2Figure 5.1 Figure 5.3
Mounting
Bracket Screw
Figure 4.2Figure 4.1 Figure 4.3
Braided Cable
Brace
Open Loop Secondary Support Screw
Support
Washer
Spring
Washer
Secondary
Support Screw
SECONDARY HANGING SYSTEM INSTRUCTIONS
1. WARNING: Secondary support is required for this product. Failure to follow the steps below could result in property damage
and/or personal injury. Feed the loop of the braided cable, preassembled to the motor assembly, up through the outlet box
mounted in the ceiling (Figure 4.1).
2. Install secondary support screw, spring washer and support washer partly into the side of the brace installed in the ceiling.
Then loop the braided cable up and over the ceiling brace and place the open loop of the braided cable around the secondary
support screw. Note: The ceiling support brace may not be accessible from below. If not, it must be accessed from above.
Important: The braided cable must make a complete circle around the support brace to secure the fan (Figure 4.2).
3. Tighten the secondary support screw, securing the braided cable (Figure 4.3).
For installation in the United States: Building codes in the U.S.A. do not require installation of a Secondary Hanging System. If
desired, the braided cable can be cut and removed using wire cutters (sold separately). Skip to FINAL INSTALLATION.
For installation in Canada: In compliance with building codes in Canada, installation of the Secondary Hanging System is required.
Black (hot)
White (neutral)
White
Black
Bare/Green (ground)
Wire Connector
3-Pin
Connector

EN I8
FINAL INSTALLATION
4. Partially insert the blade screws along with the blade washers through the blade and into the blade arm. Tighten each blade screw
with a Phillips screwdriver (not included), starting with the one in the middle. Repeat this step for the remaining blades and blade
arms (Figure 5.4).
5. Insert blade arm through slots in the side of the motor assembly. Align the holes of one blade arm with two motor screw holes in
underside of the motor assembly. Secure with two motor screws. Repeat this step for the remaining blade arms (Figure 5.5).
6. Remove one of the three fitter plate screws preassembled to the fitter plate and loosen the other two but do not remove. Feed
the 6-pin connector through the center hole in the light pan. Align the keyhole slots in the light pan with the loosened screws in
the fitter plate. Turn light pan clockwise and replace the previously removed fitter plate screw. Tighten all screws (Figure 5.6).
7. Remove one of the three light pan screws from the light pan and loosen the other two but do not remove. Connect the 6-pin
connector from the light pan to the 6-pin connector from the light kit. Lift the two keyhole slots in the light kit over the two
loosened light pan screws and turn in a clockwise direction. Then, use the previously removed light pan screw to secure the
light kit to the light pan. Tighten all screws (Figure 5.7).
8. Install the E26-base LED bulb into the socket of the light kit. Important: Make sure you allow the bulb and light kit to cool
before you replace the bulbs. Attach the glass bowl to the light kit by twisting the glass bowl firmly in a clockwise direction
until it is secure. CAUTION: Avoid cross-threading the glass during installation. Improper installation could cause the glass
bowl to be difficult to remove or fall, which could cause serious injury (Figure 5.8).
9. If desired, the wall bracket in remote pack can be installed to a wall using the provided mounting screws. The remote can be
stored in the wall bracket for easy access (Figure 5.9).
Turn on power to fan at breaker box and the wall switch. Assembly is complete.
Figure 5.5Figure 5.4 Figure 5.6
Blade Screw
Blade Washer
Blade Arm
Blade Arm
Slot
Motor Screw
Light Pan
6-pin
Connector
Fitter Plate Screw
Blade
Figure 5.8 Figure 5.9Figure 5.7
Light Pan Screw
Light Kit
Bulb
Glass Bowl
6-pin
Connector
Keyhole Slot
Wall Bracket
Mounting
Screw

EN I9
Figure 6.3Figure 6.1 Figure 6.2
Reverse Switch
OPERATING INSTRUCTIONS
Battery
Battery Cover
1. Remove the battery door from the back of the remote using a flat-head screwdriver (not included). Insert the two CR2032
batteries into the remote; ensure the positive pole of the batteries face up (as pictured) and then replace the battery door
(Figure 6.1).
2. To operate the fan using the remote, press and release the following buttons (Figure 6.2):
Fan Off - Turns the power to fan off.
High Speed - Turns on fan at high speed.
Medium Speed - Turns on fan at medium speed.
Low Speed - Turns on fan at low speed.
Light Control: Dimmable Bulbs - Press light control to turn lights off and on. Press and hold light control to dim or brighten
the lights. Non-dimmable Bulbs -Turns the lights on and off. Note: The dimmer function does not work with non-dimmable
bulbs.
Light Delay Off mode - Light stays on for 60 seconds to allow for safe exit from room. Tap Light Delay once to activate. Fan
light blinks once to confirm Light Delay is active. Press any button to cancel.
Variable Breeze - Simulates a breeze in nature. Press and hold button to activate. Press any fan speed button to cancel.
Home Shield™ - Simulates occupancy while away from home. Fan remains off and the light randomly turns on for a
minimum of five minutes and a maximum of 20 minutes. The light remains off for 60 minutes between events. Press and
hold button to activate. Light will blink twice to confirm Home Shield is active. Press any button to cancel.
LED Indicator - should illuminate when any remote button is pressed. If not, replace the DC3V, CR2032 batteries.
LEARN Button - Syncs remote to receiver (see TROUBLESHOOTING for instructions). Note: To access LEARN button,
remove battery door from back of the remote using a flat-head screwdriver.
3. Using a ceiling fan will allow you to raise your thermostat setting in summer and lower your thermostat setting in winter
without feeling a difference in your comfort (Figure 6.3).
In warmer weather, push the reverse switch toward the center of the light kit, which will result in downward airflow creating a
wind chill effect.
In cooler weather, push the reverse switch away from the center of the light kit and the fan to low, which will result in upward
airflow that can help move stagnant, hot air off the ceiling area.
Important: Wait for the fan to stop before moving the reverse switch located on the light kit. The reverse switch must be set
either completely left or right in order for the fan to function correctly. If the reverse switch is set in the middle position, the
fan will not operate.

EN I10
TROUBLESHOOTING
The fan does not
move.
The fan is noisy.
The fan wobbles
excessively.
The fan operates
correctly but the lights
are not working.
Remote does not
work.
1. Firmly push the reverse switch completely left or right.
2. Make sure the wall switch is turned on.
3. Turn the power on or check the fuse (breaker).
4. Turn the power off and check all connections at the ceiling outlet box.
1. Check and tighten all screws that hold the fan blades to the blade arms and the motor.
2. Replace the cracked blade.
3. Do not use a full range dimmer switch to control the fan speed.
4. Ensure the outlet box is secured to the building structure.
5. Ensure the mounting bracket is secured to the outlet box and that the screws are tight.
1. Ensure the 6-pin connectors are properly secured.
2. Turn the power off and check all connections at the ceiling outlet box.
3. Replace the bulbs
1. Check and tighten all screws that hold the fan blades to the blade arms and the blade arms to the
motor.
2. Switch one blade with a blade from the opposite side, or balance the fan using the blade
balancing kit.
3. Turn off the power. Loosen the canopy and verify that the mounting bracket is secure to the
electrical outlet box. The bracket must be flush without movement against the outlet box. Verify
the outlet box is secure.
4. Use a longer downrod (sold separately) or move the fan to another location.
5. Lift up the yoke cover and tighten the set screws on the yoke until secure.
PROBLEM CORRECTIVE ACTION
If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are
experiencing difficulty in installation, please contact Customer Service: 1-877-361-3883, Monday - Friday, 8am - 5pm, Central.
WARNING: Shut off the power supply before you begin any maintenance task.
1. Power surge may have cleared the memory and remote needs to be resynced to the receiver.
Syncing instructions: Turn off the main power, then turn it back on. Within 30 seconds, press and
hold the HIGH SPEED and LOW SPEED buttons (or the “LEARN” button, located in the battery
compartment) for 5 seconds. Fan will turn on at low speed and light off. This confirms the syncing
process is successful.
2. Insert new CR2032 batteries in battery compartment of the wall control.
3. If there are several remote fans in proximity, turn the power off to those fans and re-sync the fan.

EN I11
LIMITED LIFETIME WARRANTY
Set forth below, the manufacturer, Hong Kong China Electric Appliance Company (HKC) warrants the fan motor for this ceiling
fan to be free from defects in workmanship and material for the life of the product. Also, subject to the limitations below, HKC
warrants all ceiling fan parts (“ceiling fan parts” excludes the motor and parts made in whole or in part with glass) to be free
from defects in workmanship and material for a period of one year after the date of purchase by the original purchaser at retail.
All claims must be made by the original purchaser, whether such purchaser purchased the product through a store or
contractor. Ceiling fan part defects must be reported within the first year from the date of purchase. Parts made in whole or in
part with glass and the finishes of metal and other surfaces are not warranted.
Purchasers are responsible for all costs of removing and reinstalling the product. Any damage to any part caused by ordinary
wear and tear, accident, misuse, or improper installation, is not covered by this warranty. HKC assumes no responsibility
whatsoever for fan installation. Any service performed by a non-licensed electrician will render the warranty invalid.
HKC’s sole responsibility shall be to repair or replace the motor, parts, or product within the terms stated above. HKC shall not
be liable for any loss or damage of any kind, including any incidental or consequential damages resulting directly or indirectly,
from any breach of warranty, express or implied, or any other failure of this product. Some states do not allow the exclusion or
limitation of incidental or consequential damages so this limitation may not apply to you.
If the original purchaser ceases to own the fan, this warranty is voided.
Should the purchaser encounter a problem with your fan related to defects in workmanship or materials within the warranty
period associated with the defective part, HKC agrees to replace the defective part without charge, or at its option, to replace the
ceiling fan with a comparable or superior model.
HKC’s warranties are limited to the written warranties set out in this HKC ceiling fan limited lifetime warranty. All other express
and implied warranties, including, without limitation, the implied warranty of fitness for a particular purpose and the implied
warranty of merchantability are disclaimed. Some states do not allow the disclaimer of implied warranties, so this disclaimer
may not apply to you.
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department 1-877-361-3883. Monday-Friday, 8am - 5pm, Central Time.
A B C D HW
The Honeywell Trademark is used under license
from Honeywell International Inc.
Honeywell International Inc. makes no
representations or warranties with respect to
this product.
This product is manufactured for
Hong Kong China Electric Appliance, LTD.
3350 Players Club Parkway, Suite 225
Memphis, TN 38125
1 [phone]
9861 • 020323
A Glass Assembly 4A167580001
B Blade Arm (x5) 4A074540001
C Blade (x5) 4A086190001
D Remote Pack 4A000024900
HW Hardware Bag 4A000022450
51861
Home