Honeywell NOTIFIER ID2000 Series User manual

ID2000 operating
manual
997-434-000-4, Issue 4 May 2010

ID2000 Series Operating Manual
Contents
i 997-434-000-4, Issue 4
May 2010
Contents
1 Introduction 1
1.1 Associated Documents 1
1.2 The ID2000 Panels 1
1.3 Cleaning 2
2 Panel Controls and Indicators 3
3 Automatic Alarms - what to do 4
3.1 Fire 4
3.2 Pre-alarm 5
3.3 Fault 6
4 Operator Actions at Panel 7
4.1 Introduction 7
4.1.1 Top Level Display 8
4.1.2 Passcodes 9
4.2 Mute Buzzer 9
4.3 Accept 10
4.4 Evacuate 11
4.5 Silence (and Re-start) Sounders 12
4.6 Reset 12
4.7 Lamp Test and Display Control 13
4.7.1 Lamps Test In Sequence 13
4.7.2 All Lamps Lit and LCD Adjust 13
4.8 System Test 14
4.8.1 Zone Walk Test 16
4.8.2 Control Output Test 18
4.8.3 Sensor Automatic Test 20
4.8.4 Replace (VIEW) Sensor 21
4.9 Disablement and Enablement 23
4.9.1 Individual Device 25
4.9.2 Complete Zone 26
4.9.3 Outputs 27
4.9.4 Complete Zone via Remote Switch 28
4.9.5 Time-of-Day Control 28
4.10 Display, Log and Print 29
4.10.1Display and/or Log Device Data 30

ID2000 Series Operating Manual
Contents
ii997-434-000-4, Issue 4
May 2010
4.10.2Print Device Data 34
4.10.3Display and Re-Print Event Log 36
4.10.4Printer Control Modes 37
4.11 Setting the Clock 38
4.12 Select Day or Night Mode 39
4.13 Set Language 39
5 Non-latched Input Operation 40
APPENDIX 1 Status Summary A1-1 to A1-12

ID2000 Series Operating Manual
Introduction
1 997-434-000-4, Issue 4
May 2010
1 Introduction
This manual contains operating instructions for the
ID2000 Series of Intelligent Fire Detection Panels.
Users of this manual are assumed to be working with a
panel that has already been installed and configured
appropriately for the area under its supervision.
1.1 Associated Documents
This manual does not cover details on the installation or
configuration of ID2000 Series panels. For information
on these topics, refer to the ID2000 Series Installation
and Commissioning Manual (997-433-XXX) and the
ID2000 Series Panel Configuration Manual
(997-435-XXX) respectively.
Note: ‘XXX’ is the country code for the manual (000 for
the UK).
1.2 The ID2000 Panels
The ID2000 Series is a very powerful and versatile range
of Fire Alarm panels, which may be connected to up to
eight loops of addressable analogue detectors and
modules. In some installations, panels may also be
connected together in a network of up to eight panels
plus repeaters making a total of up to 32 stations.

ID2000 Series Operating Manual
Introduction
2997-434-000-4, Issue 4
May 2010
The range of ID2000 Series panels, as supplied by
NOTIFIER, are designated as follows:
a. ID2000 Basic panel - 2-loop, 16-zone Analogue
Addressable Panel. Up to three 2-loop boards can
be added, to give a maximum of eight loops.
b. ID2000 Extension panel - adds a further 64 zones, to
give a maximum of 80 zones.
Each loop has the capacity for up to 99 analogue sensors
plus up to 99 modules. Details of the available sensor
and module types are given in Appendix 1.
The ID2000 Series control panel is compatible with the
laser-based Very Intelligent Early Warning (VIEW) sensor
(FSL-751E or LPX-751). Special considerations apply
when these sensors are installed or replaced (see
Section 4.8.4).
All panels have a powerful CONTROL MATRIX feature.
This is a set of logic instructions, stored in the panel’s
internal software. It determines exactly which control
outputs (sounders, etc.) are to operate on the occurrence
of any specific Fire Alarm input, and in what manner.
Examples of the large range of options that may be
configured in a particular panel include:
a. Zoned evacuation patterns.
b. Operation of plant controls.
c. Pulsed sounder operation for alert purposes.
d. Sounders operating after a delay, or change of mode
after a delay, so as to allow time for investigation, etc.
All the control and operation functions described in this
manual can be carried out using the pushbuttons on the
front of the panel.
1.3 Cleaning
The panel case may be cleaned periodically by wiping
with a soft, damp lint-free cloth. Do not use any solvents.

ID2000 Series Operating Manual
Panel Controls and Indicators
3 997-434-000-4, Issue 4
May 2010
2 Panel Controls and Indicators
LCD display - refer to Section 4.1 for further information.
MUTE BUZZER - Refer to Section 4.2 for further information.
ACCEPT - Refer to Section 4.3 for further information.
EVACUATE - Refer to Section 4.4 for further information.
SILENCE SOUNDERS and RESOUND SOUNDERS - Refer
to Section 4.5 for futher information.
RESET - Refer to Section 4.6 for further information.
- Used to move around the LCD menus. Press
and hold to advance the printer paper (maximum of 20 lines
are advanced for a single press of this pushbutton).
- Used to confirm changes during system configuration.
0 to 9 - Used for menu selection and for data entry.
- Used to confirm an entry.
- Used to cancel an entry.
FIRE - LEDs indicate a fire condition.
ZONE FIRE - LEDs indicate affected zone(s).
FAULT - LEDs indicate a fault condition.
ZONE FAULT DISABLE/TEST - LEDs indicate affected zone(s).
Status LEDs:
DISABLEMENT PRE-ALARM REMOTE OUTPUT DISABLED
TEST SOUNDERS DISABLED REMOTE OUTPUT FAULT
EARTH FAULT SOUNDER FAULT
REMOTE OUTPUT OPERATED
POWER SUPPLY FAULT DELAY ACTIVE
SYSTEM FAULT DAY MODE
POWER
789
456
123
0
19
513
311
715
210
614
412
816
MUTE
BUZZER
MUTE
BUZZER ACCEPT
SILENCE
SOUNDERS
SILENCE
SOUNDERS
RESOUND
SOUNDERS
RESOUND
SOUNDERS
EVACUATE RESET
STATUS: NORMAL FRI 09-JUL-04 14:48:40
NOTIFIER ID2000 FIRE ALARM SYSTEM
STATUS: NORMAL FRI 09-JUL-04 14:48:40
NOTIFIER ID2000 FIRE ALARM SYSTEM
DISABLEMENT
TEST
DELAY ACTIVE
DELAY ACTIVE
DAY MODE
DAY MODE
REMOTE OUTPUT DISABLED
REMOTE OUTPUT DISABLED
REMOTE OUTPUT FAULT
REMOTE OUTPUT FAULT
REMOTE OUTPUT OPERATED
REMOTE OUTPUT OPERATED
SOUNDER FAULT
SOUNDER FAULT
SOUNDERS DISABLED
SOUNDERS DISABLED
EARTH FAULT
EARTH FAULT
POWER SUPPLY FAULT
POWER SUPPLY FAULT
SYSTEM FAULT
SYSTEM FAULT
POWER
PRE-ALARM
ID2000 FIRE CONTROL PANEL
Complies With EN54-2/4 1997
ID2000 FIRE CONTROL PANEL
Complies With EN54-2/4 1997
FAULT
ZONE FAULT
DISABLE/TEST
ZONE FAULT
DISABLE/TEST
FIRE
ZONE FIRE
ZONE FIRE

ID2000 Series Operating Manual
Automatic Alarms - What to do
4997-434-000-4, Issue 4
May 2010
3 Automatic Alarms - what to do
The following assumes that access passcode 2 is active,
or that a user interface door is fitted and is open (refer to
Section 4.1.2).
3.1 Fire
Automatic panel actions - If the system detects a fire
alarm, the panel always does the following automatically:
a. Operates the internal (high-pitched) buzzer.
b. Flashes the red FIRE lamp and numbered red FIRE
ZONE lamp.
c. Displays and prints (if printer is installed and enabled)
information about the event.
d. Operates the fire transfer relay, for fire brigade alert.
e. Operates the sounder circuits and remote Control
modules according to the panel’s Control Matrix
(configured when the system was commissioned).
f. If any delayed sounders are incorporated in the Control Matrix
program, a warning message appears on the text display
every 4 seconds, indicating how much time is left until the
first delayed control will be activated. The DISABLEMENT
LED, if configured to light, is lit steady, whilst the DELAY
ACTIVE LED state changes from steady to flashing mode.
Note: Once the timer has run out and the sounders activated,
the DELAYACTIVE lamp goes out if there are no other
disablements on the system. When the sounders are
silenced the DELAYACTIVE LED and DISABLEMENT
LED (if configured to light) light steady again.
g. Any pre-alarm indications are suppressed when the
panel enters the FIRE alarm state. In the FIRE alarm
state, the panel will give no further indication of pre-
alarm occurrences. Point information on pre-alarms
may be accessed at the LCD but are suppressed by
the fire event information.
Recommended operator actions:
1Press the ACCEPT pushbutton. More information about
the alarm appears on the display. Flashing lamps
change to steady operation. The internal buzzer changes
to intermittent operation (once every 12 seconds).
2Follow prescribed instructions for evacuation of
premises, notification of Fire Brigade and investigation
of source of Fire.
3If additional sounder operations are required to
achieve a complete and immediate evacuation of the
premises, press the EVACUATE pushbutton.
4Once evacuation of premises is achieved, or at the
direction of an authorised person, the Alarm sounders
may be silenced by pressing the SILENCE
SOUNDERS pushbutton. Any delayed operations for
which the timer has not yet expired are also cancelled
by pressing SILENCE SOUNDERS.
5To re-start sounders after having pressed SILENCE
SOUNDERS, press the RESOUND SOUNDERS
pushbutton.
6When cause of alarm has been removed and call
points and input devices have been locally reset, the
system may be returned to NORMAL by pressing the
RESET pushbutton.
EVACUATE
SILENCE
SOUNDERS
SILENCE
SOUNDERS
RESOUND
SOUNDERS
RESOUND
SOUNDERS
RESET
FIRE
ZONE FIRE
ZONE FIRE
12
ACCEPT
ACCEPT
If the panel is configured
with extendable sounder
delays: To extend the
delay, operate ACCEPT.
have different effects if the
panel is set to DAY MODE.
See Sections 4.3, 4.4 and 4.12
ACCEPT and EVACUATE pushbuttons
With panel software v.4.66, or later, the
common DISABLEMENT LED may or
may not light when the DELAYS
ACTIVE LED is lit. By default, the
DISABLEMENT LED is not lit but may
have been configured to light during
commissioning.

ID2000 Series Operating Manual
Automatic Alarms - What to do
5 997-434-000-4, Issue 4
May 2010
3.2 Pre-alarm
This is the condition when one or more input devices
has signalled a PRE-ALARM to the panel - i.e. a reading
which is higher than normal but not yet at the FIRE level.
Automatic panel actions:
a. Steady operation of the internal (high-pitched) buzzer.
b. Flashing of amber PRE-ALARM lamp.
c. Operation of those programmed control outputs which
are associated with pre-alarm events (if there are any
specified in the Control Matrix configuration).
d. Display and printing (if printer is installed and enabled)
of the event.
Recommended operator actions:
1Press the ACCEPT pushbutton. The internal buzzer
changes to intermittent operation (once every
2 minutes). More information about the pre-alarm
appears on the display. Flashing PRE-ALARM lamp
changes to steady operation.
2Check condition of detector indicated and check area
for possible fire. If the cause cannot be determined
notify authorised Servicing company.
3When cause of pre-alarm has been cleared, press
RESET pushbutton.
PRE-ALARM
RESET
ACCEPT

ID2000 Series Operating Manual
Automatic Alarms - What to do
6997-434-000-4, Issue 4
May 2010
3.3 Fault
Automatic panel actions - If the system identifies a fault,
the panel always does the following automatically:
a. Operates the internal FAULT buzzer.
b. Flashes one or more amber FAULT lamps, including
numbered amber ZONE Fault lamp(s) if appropriate.
c. Operates any control outputs which are associated
in the Control Matrix with fault events.
d. Displays and prints (if printer is installed and enabled)
information about the event.
Note: For a sensor fault, only the point of origin or a brief
reference appears on the text display.
e. Operates the fault transfer relay (for automatic alert
to a service centre).
Recommended operator actions:
1Press the ACCEPT pushbutton. More information
about the fault appears on the display. Flashing lamps
change to steady operation. The internal fault sounder
changes to intermittent operation (once every
2 minutes).
2If the fault relates to a specific sensor or module,
investigate device to see if cause of fault is
immediately apparent and can be corrected.
3In all other cases, note full description of fault and
notify authorised Servicing company.
4When cause of fault has been cleared, press the
RESET pushbutton.
Note: If the scrolling or static display messages are difficult
to read, adjust the display contrast (see
Section 4.7.2).
1
EARTH FAULT
EARTH FAULT
POWER SUPPLY FAULT
POWER SUPPLY FAULT
SYSTEM FAULT
SYSTEM FAULT
FAULT
ZONE FAULT
DISABLE/TEST
ZONE FAULT
DISABLE/TEST
RESET
ACCEPT

ID2000 Series Operating Manual
Operator Actions at Panel
7 997-434-000-4, Issue 4
May 2010
4 Operator Actions at Panel
4.1 Introduction
The panel controls and LCD display allow the following
actions to be carried out:
a. Mute the panel buzzer.
b. Accept a fire or fault condition.
c. Evacuate (and override delay to outputs, if delay is
active).
d. Silence and re-start the alarms.
e. Reset the panel.
f. Test the lamps and control the LCD display contrast.
g. Carry out system tests.
h. Disable and enable devices, zones or all outputs.
i. Display, log and print data.
j. Set the time of day clock.
k. Select Day or Night Mode for remote fire outputs.
l. Set the language displayed on the LCD.
All of these actions are security-controlled by means of
a user interface door (if fitted) or a passcode (see
Section 4.1.2).