Honeywell HZ-605 Series User manual

IMPORTANT SAFETY
INSTRUCTIONS
WARNING – READ AND SAVE THESE
OPERATING AND SAFETY INSTRUCTIONS
BEFORE USING THIS HEATER. IF YOU DO
NOT UNDERSTAND THESES INSTRUCTIONS OR
PRODUCT LABELS PLEASE CALL
OUR CUSTOMER REPRESENTIVIES AT
[phone] FOR ASSISTANCE BEFORE
USING THIS PRODUCT.
Warning – Failure to follow any of these safety
instructions could result in fire, injury or death.
YOUR RESPONSIBILITIES
Electrical appliances may expose people to
hazards that can cause severe injury as well as
death. The use of electrical products may create
hazards that include, but are not limited to,
injury, fire, electrical shock and electrical system
damage. These instructions are intended to
provide you with the information you need to
use the product and to avoid such hazards.
When using electrical appliances, basic
precautions should always be followed to
reduce risk of fire, electric shock, and injury
to persons including the following:
1. Warning – Read all instructions before using
this heater.
2. Warning – This heater is hot when in use.
To avoid burns, do not let bare skin touch
hot surfaces. If, provided, use handles
when moving this heater. Keep combustible
materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at
least 3 feet (0.9 m) from the front of the
heater and keep them away from the sides
and rear.
3. Warning – Extreme caution is necessary
when any heater is used by or near children
or invalids, and whenever the heater is left
operating and unattended.
4. Warning – Always unplug heater when not
in use.
5. Warning – Do not operate any heater with
a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged
in any manner. Discard heater or return
heater to authorized service facility for
examination and/or repair.
6. Warning – For residential use only.
7. Warning – Do not use outdoors.
8. Warning – This heater is not intended for
use in bathrooms, laundry areas and similar
indoor locations. Never locate heater where
it may fall into a bathtub or other water
container.
9. Warning – Do not run cord under carpeting.
Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange cord
away from traffic area and where it will not
be tripped over.
10. Warning – Connect to properly grounded
outlets only.
Oil-Filled Heaters
HZ-605/HZ-680/HZ-690 Series
HZ-709/HZ-710 Series
The Honeywell trademark is used by Kaz USA, Inc. under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product.

2
11. Warning – This heater is for use on
120 volts. The cord has a plug as shown in
Fig. 1, and an adapter, as shown, is available
for connecting three-blade grounding-type
plugs to two-slot receptacles. The green
grounding lug extending from the adapter
must be connected to a permanent ground
such as a properly grounded outlet box.
The adapter should not be used if a three-
slot grounded receptacle is available. Do
not circumvent the safety features of the
grounding-type plug. Do not modify the
power cord.
12. Warning – This heater draws 12.5 amps
during operation. To prevent overloading a
circuit, do not plug the heater into a circuit
that already has other appliances working.
13. Warning – It is normal for the plug to feel
warm to the touch; however, a loose fit
between the AC outlet (receptacle) and plug
may cause overheating and distortion of
the plug. contact a qualified electrician to
replace loose or worn outlet.
14. Warning – To disconnect the heater, first
turn off the product, then grip the plug body
and pull it from the wall outlet. Never pull by
the cord.
15. Warning – Do not insert or allow foreign
objects to enter any ventilation or exhaust
opening as this may cause an electric shock
or fire, or damage the heater.
16. Warning – To prevent a possible fire, do not
block air intakes or exhaust in any manner.
Do not use on soft surfaces, like a bed, or
where openings may become blocked.
17. Warning – A heater has hot and arcing or
sparking parts inside. Do not use it in areas
where gasoline, paint or flammable liquids
are used or stored.
18. Warning – Use this heater only as
described in this manual. Any other use
not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons.
19. Warning – Always plug heater directly into
a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap
(outlet/power strip).
20. Warning – Never tamper with this product
or attempt to fix it. Any tampering with, or
modification of, this product can result in
serious injury, death, or fire. Risk of electric
shock. Do not open. No user serviceable
parts inside.
21. Warning – Do not remove product labels
that contain warnings or safety instruction.
22. Caution – The output of this heater may vary
and its temperature may become intense
enough to burn exposed skin. Use of this
heater is not recommended for persons with
reduced sensitivity to heat or an inability to
react to avoid burns.
23. Caution – Before cleaning, or storage, or
when not in use, turn the product’s controls
to the OFF position and unplug the heater
from the electrical outlet and allow to cool.
24. Caution – Place the heater on a firm, level,
open surface free from obstructions and
at least 3 feet (0.9 m) away from any
combustible materials. DO NOT use on an
unstable surface such as bedding or deep
carpeting. Be sure the heater is not in a
position where it may be tripped over by
small children or pets. The heater’s rubber
feet will hold it firmly in position.
25. Caution – If your home has aluminum
wiring have a licensed electrician check
your receptacle’s connections. When
using a 1500 watt heater, aluminum wire
connections can cause a safety issue.
26. SAVE THESE
INSTRUCTIONS

3
IMPORTANT SAFETY INSTRUCTIONS REGARDING THE PLUG ON YOUR PRODUCT
Fig. 1
ELECTRICAL RATINGS
This product is rated 12.5 Amps
(1500 Watts) at 120 VAC, 60 Hz except
for the HZ-605C which is 8.33 Amps
(1000 Watts) at 120 VAC, 60Hz.
SET-UP WHEEL BASE ASSEMBLY
NOTE: DO NOT OPERATE THE HEATER WITHOUT THE WHEEL BASE
ASSEMBLIES IN PLACE. THE HEATER MUST ALWAYS BE USED IN AN
UPRIGHT POSITION. DO NOT OPERATE THE HEATER IF THE WHEELS
ARE NOT ASSEMBLED CORRECTLY.
• Make sure the heater is unplugged and in the OFF position.
• Turn the heater upside down to install wheels.
• Push wheels into each wheel base pin, until you hear them snap into
position.
• While the heater is still upside-down, position the wheel base assemblies
between the end ns. Attach them to the U-bolts on the heater and
tighten using the wing nuts provided (Fig. 2).
• Turn heater right-side up. Your heater is now ready for use.
• Place the heater on a rm, level surface free from obstructions, and at
least 3ft. (0.9m) away from any wall or combustible material.
If the controls are located at the bottom and the Honeywell logo
is upside down you have installed the wheels incorrectly (Fig. 3).
NOTE: These heaters contain oil that is permanently sealed and will
never require relling or replacing.
NOTE: THESE MODELS MAY TAKE UP TO SEVERAL MINUTES TO REACH
NORMAL OPERATIONAL TEMPERATURE.
Fig. 2 (Bottom of Unit)
Wheel Base Wheel Base Pin
Wing Nuts
U-bolts
Fig. 3
Correct Incorrect
PRODUCT SPECIFICATIONS
Models HZ-709/HZ-710 Series, HZ-605C Series,
HZ-680/HZ-690 Series
Amps 12.5 8.33
Unit Voltage 120V, 60Hz 120V, 60Hz
Max Watts 1500 1000
Max BTUs 5118 3412
Unit dims 13.6” L x 9.5” W x 25.2” H (assembled) 10”L x 9.5”W x 25.2”H (assembled)

4
HZ-680 SERIES OPERATION
• With the power switches in the OFF position, plug the heater into a 120V outlet.
• Never leave an operating unit unattended.
• Turn the thermostat control fully clockwise to its highest setting.
• This heater has 3 levels of heating. Press I for Low setting. Press II for Medium setting and press
both I and II for the High setting (Fig. 4a: l for 600W/LOW, Fig. 4b: ll for 900W/MED, or Fig.
4c: III for 1500W/HIGH). You can select the proper setting to accommodate your comfort level.
Because the Low and Medium heat settings do not require as much electricity to operate, they
are more energy ecient and may be better options if you are concerned about the amperage
draw on a circuit when the heater is in the High setting.
• Turn the power switches to ON. They will illuminate, and the heater is now in use.
• When the room reaches a comfortable temperature, slowly turn the adjustable thermostat
knob counter-clockwise until the heater goes o. This is the point where the thermostat
setting equals the room temperature. At this setting, the
thermostat will automatically maintain your desired room
temperature by cycling the heater on and o. The power
indicator will remain on when the unit is cycling on and o.
Just the heating element will actually turn on and o.
• Turning the thermostat clockwise will always increase the
“set” temperature; turning the thermostat counter-clockwise
will decrease the “set” temperature.
• Turn the power switches to OFF ( ) and unplug heater when
nished using the heater.
NOTE: THIS HEATER WILL COOL DOWN SLOWLY AFTER THE POWER IS SHUT OFF. BEFORE MOVING THE HEATER USING THE
BUILT IN HANDLE, ALLOW THE HEATER TO COOL.
Fig. 4a
Adjustable
Thermostat
Power
Level
Switches
Fig. 4b Fig. 4c
HZ-605 SERIES/HZ-690 SERIES OPERATION
• With the power control knob in the OFF ( ) position, plug the heater into
a 120V outlet.
• Never leave an operating unit unattended.
• Turn the heater ON by turning the power control knob clockwise to the desired
position. The power light will illuminate. Turning the unit on High and leaving the
unit on this setting for approximately 1 hour will speed up the heat output.
• You can then select the proper setting to accommodate your comfort level. This
heater is equipped with three dierent heat settings (Fig. 5).
The HZ-690 Series, the Low setting ( ) uses 600 watts of power, the Medium
setting ( ) uses 900 watts of power and the High setting ( ) uses 1500 watts
of power.
The HZ-605 Series uses 400 Watts of power on the Low setting ( ), 600 watts
of power on the Medium setting( ) and 1000 watts of power on the High
setting ( ).
• Turn the thermostat control fully clockwise to its highest setting.
• Because the Low and Medium heat settings do not require as much electricity
to operate, they are more energy ecient and may be better options if you are
concerned about the amperage draw on a circuit when the heater is in the
High setting.
Fig. 5
Power
Control
Power
Indicator
Light
Adjustable
Thermostat

5
• When the room reaches a comfortable temperature, slowly turn the adjustable thermostat knob counter-clockwise until the
heater goes o. This is the point where the thermostat setting equals the room temperature. At this setting, the thermostat
will automatically maintain your desired room temperature by cycling the heater on and o.
• Turning the thermostat clockwise will always increase the “set” temperature; turning the thermostat counter-clockwise will
decrease the “set” temperature.
• Turn the power control knob OFF ( ) and unplug heater when nished using the heater.
NOTE: THIS HEATER WILL COOL DOWN SLOWLY AFTER THE POWER IS SHUT OFF. BEFORE MOVING THE HEATER, USING THE
BUILT IN HANDLE, ALLOW THE HEATER TO COOL.
HZ-605 SERIES/HZ-690 SERIES OPERATION (Continued)
HZ-709/HZ-710 SERIES OPERATION
STEP 1: POWER
• Press the Power button to start the heater. Your heater will automatically start on
High power, continuous run. The display will be illuminated and will reect the
current room temperature (Fig. 6).
• To turn your heater OFF simply press the Power button again.
• Never leave an operating unit unattended.
STEP 2: HEAT OUTPUT
• This heater is equipped with three dierent heat settings. The Low setting (—)
uses 600 watts of power, the Medium setting (—
—) uses 900 watts of power and
the High setting (— —
—) uses 1500 watts of power.
You can select the proper setting to accommodate your comfort level. Because
the Low and Medium heat settings do not require as much electricity to operate,
they are more energy ecient and may be better options if you are concerned
about the amperage draw on a circuit when the heater is in the High setting.
• To change your heat setting, press the heat setting control button up or down
(Fig. 7).
• Once you have selected your desired power level the display will go back to
showing the current room temperature after 3 seconds.
STEP 3: TIMER CONTROL – AUTO SHUT-OFF
• You can set your timer for up to 18 hours automatic shut-o.
This function should only be used if you desire that the heater
be automatically shut-o after a certain period of time.
• Press the Timer button up or down to set the heater operation time
(Fig. 8). You can set the timer in increments of 1 hour up to 18 hours.
• When the display indicates your desired time, the display will
revert back to showing the current room temperature after 3 seconds.
• The heater will automatically turn-o when the set time has elapsed.
NOTE: If you wish to change your timer setting or check to see how much time is
left, simply press the timer button once and it will show you the time left. If you
want to change the time remaining, continue to push the button up or down until
you have reached your desired time. Again, after 3 seconds the display will revert
to showing the current room temperature.
Fig. 6
Desired
Temperature
Light
Heat Setting
Control
Timer
Control
Temperature
Control
Fig. 7
Fig. 8

6
HZ-709/HZ-710 SERIES OPERATION (Continued)
STEP 4: SET TEMPERATURE
• You can set your desired temperature level in 1° increments anywhere from
45° to 85° F.
• To set your desired temperature, press the temperature button.
• When the display indicates your desired temperature, the display will revert
back to showing the current room temperature after 3 seconds.
• Once you have set your desired temperature the unit will operate under this
desired setting until the unit is turned o.
• When your desired room temperature has been reached your unit will shut o
and the house icon on the top of your display will illuminate (Fig. 9). It will
stay illuminated until the room temperature decreases below your desired
temperature level, at which time your unit will turn back on.
NOTE: If you wish to change your temperature setting or check to see what you set, simply press the temperature button once and
it will show you the set temperature. If you want to change it, continue to push the button up or down until you have reached your
new desired temperature. Again, after 3 seconds the display will revert to showing the current room temperature.
FAHRENHEIT/CELSIUS SETTING
This heater oers the option to read the temperature setting in either Fahrenheit or Celsius.
• The heater will default to the Fahrenheit setting when turned on.
• The heater can only be changed from Fahrenheit to Celsius when initially turned on.
• After turning the heater on the letter F will briey be displayed on the LED screen. While the F is displayed press the
temperature button down. At this point the letter “C” will be displayed and the heater temperature settings will be
displayed in Celsius.
NOTE: THIS HEATER WILL COOL DOWN SLOWLY AFTER THE POWER IS SHUT OFF. BEFORE MOVING THE HEATER, USING THE
BUILT IN HANDLE, ALLOW THE HEATER TO COOL.
Fig. 9
TIP-OVER SWITCH FEATURE (HZ-709/HZ-710 SERIES ONLY)
This heater is equipped with a tip-over switch that disables the heater if it is tipped sideward. To restore power to the heater:
• Place the heater in the upright position.
• Press the Power button.
• The LED display will activate and normal operation will resume.
TROUBLESHOOTING
If your heater shuts o unexpectedly:
• Be sure the heater is plugged in and that the electrical outlet is working.
• Check your temperature setting. The heater may simply be o because you
have reached your desired temperature setting or your timer setting may
have elapsed.
• Check to make sure your heater is assembled correctly. If your heater is
assembled and operating incorrectly it could result in a burning odor and
smoke (Fig. 10).
For more troubleshooting tips, visit our website at: www.kaz.com
Correct Incorrect
Fig. 10

7
You should rst read all instructions before attempting
to use this product.
A. This 3 year limited warranty applies to repair or
replacement of product found to be defective in material
or workmanship. This warranty does not apply to damage
resulting from commercial, abusive, unreasonable use or
supplemental damage. Defects that are the result of normal
wear and tear will not be considered manufacturing defects
under this warranty.
KAZ USA, INC. IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY.
Some jurisdictions do not allow the exclusion or limitation
of incidental or consequential damages or limitations on
how long an implied warranty lasts, so the above limitations
or exclusions may not apply to you. This warranty gives you
specic legal rights, and you also may have other rights
which vary from jurisdiction to jurisdiction. This warranty
applies only to the original purchaser of this product from
the original date of purchase.
B. At its option, Kaz USA, Inc. will repair or replace this product
if it is found to be defective in material or workmanship.
Thereafter, while within the warranty period defective
product may be returned to Kaz USA, Inc.
C. This warranty does not cover damage resulting from any
unauthorized attempts to repair or from any use not in
accordance with the instruction manual.
D. Return defective product to Kaz USA, Inc. with a brief
description of the problem. Include proof of purchase and
a $10 US/$15.50 CAN check or money order for handling,
return packing and shipping charges. Please include your
name, address and a daytime phone number.
You must prepay shipping charges. We suggest having
tracking or delivery conrmation. Send to:
I n U.S.A.
Kaz USA, Inc.
Attn: Returns Department
4755 Southpoint Drive
Memphis, TN 38118
USA
In Canada:
Kaz Canada, Inc.
Attn: Returns Department
510 Bronte Street South
Milton, ON L9T 2X6
Canada
Please go to www.kaz.com and register your product under
the Customer Care Center and receive product information
updates and new promotional oers.
3 YEAR LIMITED WARRANTY
©2011 Kaz USA, Inc. All Rights Reserved.
US Patent No. 7,403,702
P/N: 31IM0709192
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY. DO
NOT RETURN THE HEATER TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING
YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE PRODUCT OR PERSONAL INJURY.
IF YOU HAVE ANY QUESTIONS REGARDING THIS HEATER, PLEASE CALL OR WRITE:
Kaz USA, Inc. • Consumer Relations Department
250 Turnpike Road, Southborough, MA 01772
Toll Free: 1-800-477-0457 • E-mail: consumerrela[email protected]
TROUBLESHOOTING (Continued)
CLEANING AND STORAGE
CLEANING
We recommend that the heater be cleaned at least once a month and before o-season storage.
• Turn the heater OFF and unplug it. Allow it to cool completely.
•
Use only a dry cloth to clean the external surfaces of the heater. DO NOT USE WATER, WAX, POLISH, OR ANY CHEMICAL SOLUTION.
STORAGE
• Clean your heater using he above mentioned steps.
• Wrap the cord around the cord wrap on the unit, place it in its original box and store in a cool, dry area.

8

9
CONSIGNES
DE SÉCURITÉ
IMPORTANTES
AVERTISSEMENT – LISEZ CES CONSIGNES
D’EMPLOI ET DE SÉCURITÉ AVANT D’UTILISER
LE RADIATEUR ET GARDEZ-LES. SI VOUS NE
COMPRENEZ PAS LES INSTRUCTIONS OU LES
ÉTIQUETTES APPOSÉES SUR L’APPAREIL,
APPELEZ NOTRE SERVICE À LA CLIENTÈLE
AU [phone] POUR OBTENIR DES
EXPLICATIONS ET CECI, AVANT DE VOUS
SERVIR DE L’APPAREIL.
AVERTISSEMENT – L’inobservation de ces
consignes de sécurité pourrait résulter en un
incendie, des blessures, voire la mort.
VOS RESPONSABILITÉS
Les appareils électriques peuvent exposer à des
dangers aptes à causer des blessures graves
et même la mort. Leur utilisation peut entraîner
des risques, y compris mais sans s’y limiter,
de blessures, d’incendies, de choc électrique
et de dommages à l’installation électrique.
L’objectif de ces instructions est de fournir
les renseignements nécessaires pour utiliser
l’appareil et éviter ces dangers.
L’emploi d’appareils électriques requiert
l’observation de précautions de base pour
réduire les risques d’incendies, de choc
électrique et de blessures corporelles, dont les
suivantes :
1. Avertissement – Lisez toutes les
instructions avant d’employer le radiateur.
2. Avertissement – Un radiateur qui marche
est chaud. Pour ne pas vous brûler, veillez
à ce que votre peau nue ne touche pas les
surfaces chaudes. Utilisez les poignées du
radiateur pour le déplacer, s’il en possède.
Gardez les corps combustibles – meubles,
oreillers, literie, papiers, vêtements et
rideaux, par exemple – à au moins 0,9 m
(3 pi) de l’avant du radiateur et éloignez-les
des côtés et de l’arrière.
3. Avertissement – Redoublez de vigilance
lorsque le radiateur est utilisé par des
enfants ou en leur présence et près de
personnes handicapées, ainsi que lorsqu’il
fonctionne sans surveillance.
4. Avertissement – Débranchez toujours un
radiateur qui ne sert pas.
5. Avertissement – N’employez pas un
radiateur dont le cordon ou la fiche est
abîmé, qui a mal fonctionné, a été échappé
ou endommagé d’une manière quelconque.
Jetez-le ou apportez-le à un centre de
services agréé pour le faire vérifier et/ou
réparer.
6. Avertissement – Ne convient qu’à
l’utilisation résidentielle.
appareils de cHauFFage à l’Huile
Série HZ-605/HZ-680/HZ-690
Série HZ-709/HZ-710
AVERTISSEMENT
La marque de commerce Honeywell est utilisée par Kaz USA, Inc. avec l’autorisation de Honeywell International Inc.
Honeywell International Inc. ne fait aucune assertion et n’offre aucune garantie en ce qui concerne ce produit.

10
7. Avertissement – Ne pas l’employer en plein
air.
8. Avertissement – Ce radiateur n’est pas
destiné aux salles de bains et de lavage ou
autres pièces intérieures de ce genre. Ne
le posez jamais au-dessus d’une baignoire
ou d’une cuve d’eau dans laquelle il puisse
tomber.
9. Avertissement – N’acheminez pas le cordon
sous tapis ou moquette. Ne le recouvrez
pas de carpettes, tapis de corridor, ou
autres. Ne le passez ni sous des meubles ni
sous des appareils. Éloignez-le du passage
afin qu’il ne puisse pas faire trébucher.
10. Avertissement – Ne le branchez que sur
prise convenablement mise à la terre.
11. Avertissement – Ce radiateur se branche sur
120 volts. Le cordon est équipé de la fiche
illustrée à la fig. 1. Un adaptateur, illustré,
est disponible pour brancher les fiches
tripolaires (avec terre) sur prises bipolaires.
L’ergot vert en saillie de l’adaptateur
doit être connecté à une mise à la terre
permanente, une boîte de sortie à la terre
telle, par exemple. Un adaptateur ne doit pas
être employé quand une prise de courant
tripolaire est disponible. Ne pas contourner
le dispositif de sécurité de la fiche tripolaire
et ne pas modifier le cordon.
12. Avertissement – Ce radiateur prélève 12,5
ampères au réglage haut. Afin de ne pas
surcharger le circuit, ne branchez pas le
radiateur sur un circuit qui alimente déjà
d’autres appareils en marche.
13. Avertissement – Il est normal que la fiche
soit un peu chaude au toucher ; une
connexion prise de courant alternatif et fiche
mal assujettie peut surchauffer et déformer
la fiche. Demandez à un électricien de
remplacer les prises ayant du jeu ou usées.
14. Avertissement – Pour débrancher le
radiateur, éteignez-le puis tenez la fiche
entre le pouce et l’index pour la sortir de la
prise. Ne tirez jamais sur le cordon.
15. Avertissement – Veillez à ce qu’aucun
corps étranger ne pénètre dans les orifices
d’aération ou d’évacuation, sous peine de
provoquer choc électrique ou incendie et
d’abîmer l’appareil.
16. Avertissement – Pour éviter tout risque
d’incendie, ne bouchez les orifices
d’admission d’air ou d’évacuation en aucune
façon. Ne posez pas le radiateur sur une
surface molle, un lit par exemple, qui
pourrait boucher les orifices.
17. Avertissement – Un radiateur renferme des
pièces chaudes et produisant des étincelles.
Ne l’employez pas dans les lieux où sont
utilisés ou entreposés essence, peinture ou
liquides inflammables.
18. Avertissement – N’utilisez le radiateur que
tel que décrit dans ce guide. Tout autre
emploi que ne conseille pas le fabricant peut
être source d’incendie, de choc électrique ou
de blessures corporelles.
19. Avertissement – Branchez toujours le
radiateur directement sur la prise murale.
N’employez ni cordon prolongateur ni prise
déplaçable (barre multiprise).
20. Avertissement – N’altérez pas le radiateur et
n’essayez pas de le réparer. Toute altération
ou modification pourrait entraîner blessures
graves, mort ou incendie. Risque de choc
électrique. Ne l’ouvrez pas, il ne contient pas
de pièces que vous puissiez réparer.
21. Avertissement – N’enlevez pas les étiquettes
de mise en garde ou d’instructions de
sécurité.
22. Attention – Le rendement du radiateur peut
varier et sa température être assez élevée
pour brûler la peau nue. Il est déconseillé
d’employer le radiateur aux sujets dont