Honeywell MIWI350 User manual

MIWI350 Solar Power Quick Start Guide
Product Features
•Internal or External Mounted Display
•Optional Backup Battery for Uninterrupted EVC Functionality
Power Supply Options
General Safety Precautions
Warning
Caution
Safety and Hazardous Information
Product Overview
Solar Power with rechargeable Sealed Lead-Acid Battery (Refer to FD-612)
Battery - Alkaline Packs (Dual/Quad) (Refer to FD-613)
External DC Supply Input (7.5V to 24V)
Modem Power Control
Available in UMB (Universal Mounting Bracket), Wall, Pipe, and Portable mounting options
Compatible with MasterLink and Power Spring software
CSA C/US Class 1, Division 2, Group C & D
or Electronic Recorder
A built-in electronic cellular modem
This quick-start guide covers Solar Power with rechargeable Sealed Lead-Acid Battery option only.
Close the door of the MIWI350 device properly
Check the lock and latchet, and lock the MIWI350 device properly
Check the padlock properly while locking the MIWI350 device
(Refer to FD-614)

Cable Gland Entries
Unpacking
2
Lead-Acid or Alkaline Battery Pack
Internal/External Display Cable gland location for
Pulse Output and
Pulse Input
Modem
Pressure Transducers
P1 and P2
Power D
istribution
Board
Latch and Lock
Case Assembly
Optional Backup
Battery Pack
Solar Charge ControllerDoor Assembly
Terminal block to connect to
external incoming power
UMB Mount on the Meter
Wall Mount
Pipe Mount
mounting options:
Instrument Mounting Options
Portable Mount
P1 Pressure
Transducer
Temperature
Probe
Ground/Earthing
Incoming Power
P2 Pressure
Transducer
Pulse Input
Pulse Output
P3 Pressure
Transducer (Future)

Setting up the MIWI350 Device
02
Release the door latches of
the device one at a time, and
open the door of the device
Install UMB on Instrument Drive
gas meter
(if applicable)
3
Route the pulse input/output cables
through the glands (if applicable)
04
3
01
0
05
Install the temperature probe to the
pipeline and tighten the nut to avoid
leakage (if applicable)
Route the external power cable
through the 05 gland and connect
to power terminal block
03
05
04

10
4
06 07 08
09
11
For a fresh Lead-Acid Battery, the No Load Voltage is expected to be between 12.5–13.5VDC.
WARNING: Please perform the No Load Battery Voltage measurement in an area rendered
Non-Hazardous. Please Exercise Caution to ensure the Battery Terminals do not come in
contact in any metal other objects during the measurement/handling.
Configure modem/EC/ERX350/HMI settings
(For more information, refer MIWI350 Installation and Operational Manual - FD-610)
(-cw)
(+cw)
check
Battery Installation

Solar Power Supply Wiring with MIWI350-EC or MIWI350-ER
Reference Wiring Diagrams
Solar Power Supply Wiring without MIWI350-EC or MIWI350-ER
5
SOLAR POWER with 7Ah BATTERY SOLAR POWER with 21Ah BATTERY
Note: The cable color code/pin mapping are only for illustration purpose and don’t match the actual cables.
40-6169-2
40-6169-1
CONNECT
TO
SOLAR
PANEL
POWER
CONNECTOR
CONNECT
TO
SOLAR
PANEL
POWER
CONNECTOR
40-6169-1
40-6169-3
SOLAR POWER With 7Ah BATTERY SOLAR POWER With 21Ah BATTERY
Note: The cable color code/pin mapping are only for illustration purpose and don’t match the actual cables.
40-6169-2
40-6169-1
CONNECT
TO
SOLAR
PANEL
POWER
CONNECTOR
CONNECT
TO
SOLAR
PANEL
POWER
CONNECTOR
40-6169-1
40-6169-3

For more information:
To learnmore outoneywell s Smart Gas
Metering Solutions, visit
www oneywellprocess com or contact your
eywell Process Solutions representative
Honeywell Process Solutions
128 Kemper Me ow Drive Cincinnati,
O
NOTES
Description
Part Number
SOL C LOAD O/P CABLE
21Ah LEAD-ACID BATTERY CABLE
7Ah LEAD-ACID BATTERY CABLE
©2019 Honeywell International Inc
April 2019
List of associated cable assemblies pre-installed in the device