Honeywell RAE Systems NeutronRAE II User manual

NeutronRAE II
User’s Guide
www.raesystems.com
Personal Radiation Monitor
P/N 047-4204-100
Revision B, January 2013

Read Before Operating
This manual must be carefully read by all individuals who
have or will have the responsibility of using, maintaining,
or servicing this product. The product will perform as
designed only if it is used, maintained, and serviced in
accordance with the manufacturer’s instructions.
CAUTION!
To reduce the risk of electric shock, turn off power and remove
batteries before removing the monitor cover. Never operate this
monitor while the cover is removed. Remove monitor cover and
sensor modules only in an area known to be non-hazardous.
WARNING
To prevent ignition of flammable or combustible atmospheres,
disconnect power before servicing.
WARNING
Do not mix old batteries with used batteries or mix batteries
from different manufacturers.
WARNING
Substitution of components may impair performance.
!
!
!
!
This product complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept
any interference received, including intereference that may cause
undesired operation.

1
www.raesystems.com
Warnings
For safety reasons, this equipment must be operated
and serviced by qualified personnel only. Read
and understand the user manual completely before
operating or servicing.
Computer Interface
Do not transfer data by means of the Bluetooth®interface in
hazardous atmospheres.
Static Hazard
Clean only with a damp cloth.
Long-Term Storage
Reliable performance of this radiation detector is based upon
regular usage. For long-term storage, the battery should be
disconnected. Preparation for use after long storage requires
installation of the batteries and a warm-up period of at least
10 minutes for the sensors to equilibrate. The user should
recognize that sensor life is based upon the purchase date.
!
!
!
!
!

2NeutronRAE II
Avertissements
Pour des raisons de sécurité, cet équipement doit
être utilisé, entretenu et réparé uniquement par un
personnel qualifié. Étudier le manuel d’instructions
en entier avant d’utiliser, d’entretenir ou de réparer
l’équipement.
Câble de Computer
Ne transférez pas les données au moyen de l’interface de
bluetooth en atmosphères dangereuses.
Danger Risque D’origine Electrostatique
Nettoyer uniquement avec un chiffon humide.
Stockage à Long Term
Le fonctionnement durable de ce détecteur de rayonnement
est conditionné par une utilisation régulière de celui ci. Lors
d’un stockage à long terme, la batterie doit être déconnectée.
Le rédémarrage aprés une longue période d’arrêt, nécessite la
réinstallation de la batterie, et une période de chauffage de 10 mn
afin que les capteurs se mettent à l’équilibre. L’utilisateur doit être
conscient que la durée de vie indiquée pour le capteur démarre à
sa date d’achat.
!
!
!
!
!

3
www.raesystems.com
Contents
NeutronRAE II Features .......................................4
General Information ...........................................5
Inserting & Replacing Batteries..................................6
User Interface ...............................................7
User Interface Icons ...........................................8
Turning the NeutronRAE II On and Off ...........................8
Flipping the Screen ..........................................12
Operation ..................................................13
Normal Operating Mode ...................................13
NORM ................................................14
CAL ..................................................14
PEAK .................................................15
MIN ..................................................15
DOSE .................................................16
STAT .................................................16
COMM ................................................17
TEST .................................................18
Programming Mode .......................................20
Alarm Set ..............................................21
Datalog Set .............................................22
Monitor Set ............................................23
Back Lite .............................................24
Buzz & Lite ...........................................25
Vibrate mode ..........................................25
Temp Unit ............................................25
Gamma Unit ..........................................26
Change Date ..........................................26
Change Time ..........................................26
Quit .................................................27
Default Settings and Parameter Ranges ..........................27
Specications ...............................................29
Limited Warranty ............................................34

4NeutronRAE II
LED alarm
LCD showing operation
parameters and
radiation measurements
MODE key for
selecting mode
and function
Buzzer alarm
SET key for
selecting
or setting
parameters
Battery
compartment
cover screw Belt clip
Battery
compartment
LED alarm
Front View
Rear/Side View
Sensor location

5
www.raesystems.com
General Information
The NeutronRAE II is a rapid detector
of γ-ray (gamma) and neutron radia-
tion sources. Because of its high
sensitivity, it can alert rst responders
to the presence of a radiation threat
well before they might be exposed
to health-threatening levels. This
personal radiation detector features a
loud audible alarm, big, bright ashing
LEDs, and a vibration alarm. For stealth
operations, law enforcement personnel can disable each
alarm separately.
NeutronRAE II’s water-resistant design makes for reliable
operation in wet environments. Its sensitive Cesium Iodide
(CsI) and Lithium Iodide (LiI) scintillators provide fast
response to radiological threats.
The NeutronRAE II accumulates dosage. Stored dosage data
can be cumulative or cleared and reset for each use period.

6NeutronRAE II
NeutronRAE II Features
Inserting & Replacing Batteries
NeutronRAE II uses two AA alkaline batteries as
its power source (use only Duracell MN1500 or
Energizer E91). To change the batteries:
1. Use a coin or
screwdriver to open
the cover on the
side of the unit.
Turn the screw
counterclockwise to
loosen the screw, and
then tilt the cover off.
2. Insert batteries into the compartment
according to the legend on the rear of
the NeutronRAE II, making sure the
batteries’ polarity is correct.
3. Replace the cover and turn the screw
clockwise to secure the cover.

7
www.raesystems.com
User Interface
NeutronRAE II’s user interface consists of the display, LEDs,
alarm transducer and two buttons, labeled MODE and SET.
The LCD display provides visual feedback that includes
time, functional mode, battery condition, and gamma and
neutron radiation measurements.
LCD display
Current time
Gamma alarm
information
Battery status
Functional
mode
Gamma radiation
measurement
Unit of
measure
(gamma)
S
E
T
M
O
D
E
MODE and SET switches
Datalog indication
Neutron radiation
measurement
Neutron reading
sign
Unit of
measure
(neutron)
Neutron alarm
information

8NeutronRAE II
User Interface Icons
Icon Indication
Battery Voltage low
Battery Low alarm triggered
Battery fully charged
Low Gamma alarm triggered
High Gamma alarm triggered
Gamma Over-Range (reading over 20 mR/h)
Gamma Overload
Low Neutron alarm triggered
Neutron Over-Range (reading over 100 cps)
Neutron Overload
Bluetooth®communication active
Datalogging active (ashing)