Honeywell Xenon XP 1952g User manual

Xenon™ XP 1952g/1952g-BF
CCB01-010BT/CCB01-010BT-BF
CCB-H-010BT/CCB-H-010BT-BF
Cordless Area-Imaging Scanner and Charge Bases
Quick Start Guide
1952-52BF-EN-QS-01 Rev (a)

1
Agency Model: 1952/1952-BF/ CCB-H-010BT/ CCB-H-010BT-BF
Note: Refer to your User Guide for information about
cleaning your device.
Getting Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
When the base is connected and powered up, put the scanner in
the base to establish a link. The green LED on the base flashes
to indicate the scanner’s battery orcharge pack is charging.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.

2
Connecting the
Scanner
USB:
Note: If you are charging the scanner using the USB cable, the
current available for charging is reduced and charge times
are increased. Charging via the power supply is faster.
CCB01-010BT or CCB01-010BT-BF Base:
CCB-H-010BT or CCB-H-010BT-BF Base:

3
Keyboard Wedge:
CCB01-010BT or CCB01-010BT-BF Base:
CCB-H-010BT or CCB-H-010BT-BF Base:

4
RS232 Serial Port:
CCB01-010BT or CCB01-010BT-BF Base:
CCB-H-010BT or CCB-H-010BT-BF Base:

5
RS485:
CCB01-010BT or CCB01-010BT-BF Base:
CCB-H-010BT or CCB-H-010BT-BF Base:

6
Reading
Techniques
The view finder projects an aiming beam that
should be centered over the bar code, but it
can be positioned in any direction for a good
read.
Note: If the scanner beeps 3 times when
scanning a bar code, the link has not
been established. If the scanner beeps
once, the link has been established.
Standard Product Defaults
The following bar code resets all standard product default set-
tings.
Standard Product Defaults

7
RS485
Interface
The RS485 interface defaults to port 5B. If you have an IBM POS
terminal using port 9B, scan the appropriate code below to pro-
gram the terminal, then power cycle the cash register.
IBM Port 9B HHBCR-1
Interface
IBM Port 9B HHBCR-2
Interface
Note: For additional RS485 interface selections, see the
User Guide for your product.
USB Serial
If you are using a Microsoft® Windows® PC, you must
download a driver from the Honeywell website. The
driver will use the next available COM Port number.
Scan the following code to program the scanner to emulate a
regular RS232-based COMPort.Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automati-
cally use a class driver.
USB Serial
Note: No extra configuration (e.g., baud rate) is necessary.

8
USB PC
Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Keyboard
Country
USB PC Keyboard
Scan the appropriate country code below to program the key-
board layout for your country or language. By default, national
character replacements are used for the following characters:
#$@[\]^‘{|}~ Refer to the ISO 646 Character Replacements chart
in your User Guide to view the character replacements for each
country.
USA (Default)
Belgium
Denmark
Finland

9
France
Great Britain
Norway
Switzerland
Germany/Austria
Italy
Spain
Note: For a complete list ofcountry codes, see the UserGuide for
yourproduct.