Honeywell HD3USX User manual

Document 800-13599 – Rev B – 12/2012
Configuration Guide
HD3US(X)
Ultra Wide Dynamic
Indoor Minidome Camera

2
Revisions
Issue Date Revisions
A 11/2012 New document.
B 12/2012 Change to document title. UL/CSA certification added to
Specifications section.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
DO NOT OPEN
RISK OF ELECTRIC SHOCK

3
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Programming the Camera. . . . . . . . . . . . . . . . . . . . . . . . . 4
Exposure Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Color Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Day&Night Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Function Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Motion Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Privacy Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Sync Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4
Introduction
This document provides instructions for configuring the HD3US(X) minidome camera
settings. These instructions are intended for system installers, administrators, and
operators. For information about installing the camera, refer to the HD3US(X) Ultra WDR
Indoor Minidome Camera Quick Installation Guide (800-13598).
Programming the Camera
The camera is programmed using the on-screen display (OSD) menus. You can connect a
portable monitor during installation using the supplied adapter cable.
To show the OSD main menu, press the OSD
controller joystick located on the camera
control board.
Move the joystick up or down to navigate
through the menu options. Move the joystick
right to change a menu setting.
When a menu option or setting is followed by
two dots (..), press the joystick to access the
next screen. To go back to the main menu,
select RETURN.., and then press the joystick.
UP
DOWN
RIGHTLEFT

5
The camera has the following OSD menu structure:
1. EXPOSURE
LENS
AE PREFERENCE
BLC
WDR
AGC
SENSE-UP
METER ZONE
EXIT JUMP
2. COLOR
WB MODE
COLOR GAIN
EXIT JUMP
3. DAY&NIGHT
D&N MODE
BW BURST
EXIT JUMP
4. FUNCTION
MIRROR
SHARPNESS
GAMMA
3D DNR
D-ZOOM
EXIT JUMP
5. MOTION
MOTION
MOTION ZONE
EXIT JUMP
6. PRIVACY
PRIVACY MASK
MASK COLOR
EXIT JUMP
7. SYNC
INT1
INT2
LL
EXIT JUMP
8. SETUP
PC CONTROL
TITLE
LANGUAGE
OMNI LENS
FLUORESCENT
DIGITAL VIDEO OUTPUT
EXIT JUMP
9. EXIT
EXIT
SAVE&EXIT
FACTORY SET

6
Exposure Menu
EXPOSURE LENS
Select DC or MANUAL. Press the OSD controller joystick to set the lens FOCUS METER.
Set the FOCUS METER to the maximum value for a clear image.
DC:
DC GAIN adjusts iris speed (0–255). AI THOLD defines the gain level (-48–60).
MANUAL:

7
EXPOSURE AE PREFERENCE
Set AE PREFERENCE to INDOOR or OUTDOOR depending on the camera environment.
EXPOSURE BLC (Backlight Compensation)
Set BLC to ON or OFF. When BLC is ON, adjust SHADOW GAIN as desired. A higher value
decreases foreground brightness; a lower value increases it.

8
EXPOSURE WDR (Wide Dynamic Range)
Set WDR to LOW, NORMAL, MEDIUM (default), HIGH, or CUSTOM.
CUSTOM mode lets you adjust BIAS and LIMIT as desired. BIAS defines the WDR level in
the range of LIMIT (-30–30). LIMIT defines the WDR level (0–36).
CUSTOM MODE

9
EXPOSURE AGC (Auto Gain Control)
Set AGC to LOW, MEDIUM, or HIGH (default). A high AGC setting produces a brighter
image in low light but also produces more noise.
EXPOSURE SENSE-UP
SENSE UP automatically activates slow shutter function when a scene is too dark. Select a
value from X2 to X64 to set the frame integration level. The default setting is X4.

10
EXPOSURE METER ZONE
Note For advanced users only.
METER ZONE defines the specific zone to which AE or WB is applied.
WHITE: Adjust the location of the zone.
GREEN: Reduce the zone area.
RED: Enlarge the zone area.
Press and hold down the joystick to exit.