Honeywell HICC-1600TVI User manual

Honeywell
i
Honeywell
HD Network IR Bullet Camera
Operation manual
HICC-1600TVI
HICC-2600TVI

Honeywell
i
Contents
1 Introduction...........................................................................................................................................1
Performance Characteristics Features................................................................................1
2 Hardware Installation..........................................................................................................................2
System requirement................................................................................................................2
Installation environment.........................................................................................................2
Installation environment requirements..........................................................................2
Recommend operating environment.............................................................................2
Hardware installation steps.............................................................................................2
Network connection..........................................................................................................4
Connection instruction............................................................................................................4
3 Operating Guide for IP Camera........................................................................................................5
Set the IE Browser..................................................................................................................5
Download and Install ActiveX................................................................................................5
Login .........................................................................................................................................7
Live view...................................................................................................................................8
System specification setting................................................................................................10
Device Info.........................................................................................................................10
PTZ setting........................................................................................................................10
Display settings................................................................................................................. 11
Encoding............................................................................................................................12
Video Parameters............................................................................................................. 12
Motion Detection............................................................................................................... 13
Video Tampering..............................................................................................................14
Video Mask........................................................................................................................15
Network Settings..............................................................................................................16
DDNS Setting....................................................................................................................17
NTP Settings.....................................................................................................................18
Email Settings...................................................................................................................18
FTP Settings......................................................................................................................19
Alarm Input........................................................................................................................19
Alarm Output.....................................................................................................................20
Exception Settings...........................................................................................................21
User Info............................................................................................................................22
System Update.................................................................................................................23
Storage Management......................................................................................................23
Restore...............................................................................................................................24
Local Setting......................................................................................................................24
File management...................................................................................................................25
Log search..............................................................................................................................26
4 Appendix.............................................................................................................................................27
SPECIFICATIONS................................................................................................................27
Network Interface of IP Camera.........................................................................................28
Default Network Parameters...............................................................................................28
IP Camera DDNS............................................................................................................. 29
Visit IP camera under different network environments...................................................29
LAN.....................................................................................................................................29

Rev. A
Static IP..............................................................................................................................29
Dynamic IP........................................................................................................................30
Internet...............................................................................................................................30
Frequently asked questions................................................................................................34

Honeywell
iii
CAUTION
•Non-technician should not try to operate this camera before reading this manual carefully. (This manual are subject to change
without prior notice.)
•Cut the power supply off before operating the device to avoid damage caused by mal-operation.
•Interior of the camera are precision optical and electrical instruments. Heavy pressure, shock and other incorrect operations
should be prevented. Otherwise, may cause damage to product.
•Please do not use the product under circumstances where the limits exceed the maximum specified temperature, humidity or
power supply specifications.
•Contents in this manual may be different from the edition that you are using. Should any unsolved problem occur given that the
product is used according to this manual, please contact our technical support department or your product suppliers.
•This manual content will be updated unscheduled, our company reserves the right to do manual contents update without
further notice.
•The default username for this device is “admin”, and the password is blank. Default IP address is 192.168.1.188, HTTP port is
80, device port is 5050.

Honeywell
v
PACKING LIST
Check if the packing contents match the packing list on receiving the products. The packing list is as below.
Part Quantity
HICC-1600TVI / HICC-2600TVI 1
Mounting kit 1
Operation manual 1
Certificate of approval 1
CD 1
Contact your local retailer if anything is missing in your package.

Honeywell
1
1 Introduction
Performance Characteristics Features
•720P @ 30fps [HICC-1600TVI]
1080P @ 30fps [HICC-2600TVI]
•H.264, and MJPEG simultaneously (Dual-encoders)
•H.264 high profile – saves bandwidth and storage
•Built-in IR LED and ICR for day & night surveillance without color shift
•WDR, 3DNR, DC IRIS, and Anti-flicker
•Comprehensive I/O ports: audio in, audio out, video out, Alarm In, Alarm Out, RJ45, TF, RS485
•Built in Power over Ethernet (PoE); 100Base-T Ethernet
•Event triggering – camera tampering, Motion detection, Network lose, Alarm Input, Video Lose
•Event trigger action – SNAP, Record video in TF, send to FTP, send to Email, External output activation, voice alert, go preset and tour,
notify to CMS.
•Compatible with Honeywell Universal Surveillance (HUS) Platform and NVRs
•ONVIF Profile S compliant, IP66

Honeywell
2
2 Hardware Installation
System requirement
•LAN or WAN Internet to connect server, via PC Ethernet ( network card or network cable) TCP/IP protocol （Windows
/NT/2000/XP) connect , suggest Internet Explorer 5.0 version or later.
•Monitor and PC configuration:
CPU: PⅢor latter, RAM: 512M or latter( Above DirectX8.1)
•Monitor: 17",1024×768 resolution
•Operation system: Windows NT, Windows2000, Windows XP
Installation environment
Installation environment requirements
Far away from high-temperature resource and environment; improper place for ventilation; avoid install on shaky place.
Recommend operating environment
Temperature:-20 ~ +55℃
Humidity: Max 85%RH
Hardware installation steps
Please make sure LAN and WAN are working order before installation of the IP camera . After checked all the network system in good
condition, keep your hands clean and dry, following the steps bellow.
•Unpack the box to check the goods
•Take out all goods which needed for installation from the box
•Take off the camera rod cover, demount the screws on the lamp panel and insert the SD card. Please refer to the SD card
installation steps below.
Figure 2 1 HICC-1600TVI
Micro SD card installation
site

Honeywell
3
Figure 2 2 HICC-1600TVI
Figure 2 3 HICC-2600TVI
Figure 2 4 HICC-2600TVI
•Connect related cables according to actual need (Power line, network line, audio line etc.)
•Connect the power supply
Please read the Note carefully, any question you should contrast us without hesitation.
Note:
•When open the box, please check all of parts carefully, confirm the parts in the box as same as packing list.
•Please read the user manual carefully before the installation.
•Make sure to turn off all the power when install the camera
•Please confirm the power transformer, avoid the device damage with unmatched power source
Micro SD card installation
site
Insert Micro SD card
following the direction shown
in Figure 2-4
Insert Micro SD card
following the direction shown
in Figure 2-2

Honeywell
4
Network connection
•LAN connection
Use one network line to connect IP camera with concentrator or switchboard of the LAN.
•WAN connection
Use one network line to connect IP camera with Router or XDSL Modem/Cable Modem. as shown bellow.
•Connect the power
After connect the power source, the network camera will start operation automatically.
Connection instruction
Analog video output
Powe
r
su
pp
l
y
in
p
ut
RJ45
Alarm output, 485 A/B port
Audio input
Audio output
2 channels Alarm
input

Honeywell
5
3 Operating Guide for IP Camera
Set the IE Browser
If you visit IP camera for first time, Please set the IE browser.
Setting method: Open the IE browser, click Internet Option into the "Security" page, click the "Custom Level", and then follow steps to set the
IE browser
Download and Install ActiveX
You need to install ActiveX Control when you visit IP camera for the first time through IE browser.
ActiveX installing method:
Download installation
Input the IP address of IP camera (default address http://192.168.1.188.) in Internet Explorer to enter into login page, users can refer to
the “ NETWORK SETTINGS” under “SETUP” menu to set the network.
Notice the below information hint, click “ Install”. As Figure 3-1

Honeywell
6
Figure 3 1
A file download dialog will pop out, click “Next” to installation. As figure 3-2.
Figure 3 2
Select the ActiveX installation and storage file, the default installation and storage file is c:\Program Files\webactivex, and click “Next” to enter
next dialog. As figure 3-3
Figure 3-3
Click “ Install” to enter into the next dialog. As figure 3-4.

Honeywell
7
Figure 3-4
Click “Finish” to complete the ActiveX installation. As figure 3-5.
Figure 3-5
Login
Reopen Internet Explorer after ActiveX installation completes, input IP address ( http://192.168.1.188,)oftheIPcameratoturntologinpage,
enter username (default setting is admin) and password (default setting is 123456), click login to enter into main interface(see Figure 3-6):
Figure 3 6

Honeywell
8
Live view
Live preview interface as figure 3-7.
Figure 3 7
In the Live view interface, users can do operations such as voice intercom, listen, full-screen preview, video record, alarm information check,
PTZ and lens control, brightness, contrast, preset setting, cruise, track setting and etc.
zVoice intercom：Connect sound pick-up device on the audio input port and active loudsperker on the audio outport port, then click
the talkback icon. Turn on the voice intercom switch and the icon shows as , the talkback between PC and IP camera can
be performed. Audio input setting as default mode.
zSNAP: click button, snap the current image and save it in .JPG format automatically to the storage directory of snapped
images. The default path is C:\Program Files\PREVIEW, and the storage path is changeable.
zFull Screen: Live preview in full screen, press keyboard ESC to exit from full screen display.
zRecord: ON/ OFF selectable. When select ON, the icon turn blue as ., and device do video recording and saved in the
appointed files as I8 format
zAlarm Info: Warns light flashing when camera device inform alarm. Support kinds of alarms record, and setup or remove the alarm
setting,clear the alarm information.
zZoom-in: Use the mouse to do local zoom for the video display area by scrolling the mouse wheel.
zPTZ control: Up/ down/ left/ right/ auto/ adjust the PTZ rotate speed, etc. As figure 3-8.
zLens control: Do scaling, focus, iris operation, as figure 3-8.
zBrightness: Adjust the image brightness. As figure 3-9.
zContrast: Adjust the image contrast. As figure 3-9.
zPTZ setting: Set the preset, cruise, tracking, etc. As figure 3-10.
Preset setting: Adjust the camera to the appointed angle and location through directional buttons, and then select a preset
number on the preset drop down list, click to set it.
Clear preset:Select a preset number which needed to delete on the preset drop down list, then click to clear it.
Call preset: Select a preset number which needed to call on the preset drop down list, then click to call it.

Honeywell
9
Cruise: 255 presets addable, cruise time 1-255s adjustable, cruise speed 1-10 levels selectable. All cruise tracking can
be call and delete independently.
Tracking path setting: Select a tracking number on the tracking drop down list, then click , after a series PTZ
operation, click to complete and storage the tracking.
Clear tracking path: Select a tracking number on the tracking drop down list, click to clear it.
Call tracking path: Select a tracking number on the tracking drop down list, click to call it.
•Cyclotron arrow: Restore the default parameters. As figure 3-10.
Figure 3 8
Figure 3-9
Figure 3 10

Honeywell
10
System specification setting
Device Info
IP Camera “Device Info” interface as figure 3-11.
Figure 3 11
zDevice Name: Edit the camera name
zDevice Sn: Display the device Sn
zDevice Type: Display the device type
zSerial No. : Display the product serial No.
zMaster Version: Display the software version date
zHardware Version: Display the hardware version number
zFormat: Switch to select the PAL and NTSC image scanning system
zDevice Time: Set and display the device current time
After all parameters setting completed, click “Save” and then it comes into effect immediately.
PTZ setting
IP Camera “ePTZ Set” interface as figure 3-12.

Honeywell
11
Figure 3-12
zProtocol: Support Pelcod，Pellcop，PellcoF protocol
zAddress: 0-255 adjustable
zBaud Rate: Serious baud rate selectable
zOperation method: Connect analog high speed dome at the IP camera AB port, set the protocol and baud rate, and control the high
speed dome through IPC preview interface
After all parameters setting completed, click “Save” and the it comes into effect immediately.
Display settings
IP Camera “Display settings” interface as figure 3-13.
Figure 3-13
zName:Modify the appointed channel name

Honeywell
12
zTime Format: Select different time display mode for the appointed channel
zDate Format: Select different date display mode for the appointed channel
zBright: Adjust the brightness for the appointed channel
zContrast: Adjust the contrast for the appointed channel
zSaturation: Adjust the saturation for the appointed channel
zHue: Adjust the hue for the appointed channel
zTitle Location: Set the channel title location for the appointed channel
zDate Adjustment: Set the channel date location for the appointed channel
zCyclotron arrow: Restore the default parameters
After all parameters setting completed, click “Save” and the it comes into effect immediately.
Encoding
IP Camera “Encoding” setting interface as figure 3-14.
Figure 3-14
zCompress type: Main Stream(Normal)/ Sub Stream/ Main Stream(Event) selectable
zStream: Including complex stream/ video stream two types
zResolution: According to the front camera supported, how the camera resolution type supported, the corresponding resolution will
selectable
zBitrate Type: Constant/ Variable selectable
zBitrate: Set different bitrate for different channels
zFrame Rate: Select different frame rate in the drop-down list,, default is “Full Frame”
zQuality: Select different image quality according to your need, default is “Highest”
zVideo Encode: H.264/ MJPEG two kinds of video encode format
zI frame Interval: Set the I frame internal time
After all parameters setting completed, click “Save” and the it comes into effect immediately. ( “Setup” setting will change the front
camera parameters directly)
Video Parameters
IP Camera “video Parameters” setting interface as figure 3-15.

Honeywell
13
Figure 3-15
zDay&Night Mode: Outside Trigger/ Auto/ Color/ Black White four kinds of mode selectable. Non infrared IP cameras default mode is
Auto, and infrared IP cameras default mode is Outside Trigger. According to the IP camera type and actual scene to select the
Day&Night mode.
zSwitch time: Day&Night switch delay time, 0-30s selectable, and default is 3s.
zDay-Ni-Threshold: 0-255 selectable, users adjust it according to the need, default is 44.
zNi-Day-Threshold: 0-255 selectable, users adjust it according to the need, default is 119.
zColor: Normal/ Bright/ Nature three options, default is Normal.
zMirror: Close/ Horizonal Mirror/ Vertical Mirror/ 180° Rotation four options, default is Close.
zWDR: Close/ Low/ Medium/ High four options, default is Close.
z3DNR: Close/ Low/ Medium/ Higher/ High five levels, default is Close.
zSharpness: 0-255 selectable, default is 128.
zGain: Low/ Lower/ Medium/ Higher/ High selectable, default is Medium. The higher of the Gain, the more of the sharpness.
zSharpness: Auto, 1/30(25)-1/10000, the default is Auto
zExposure Control Mode: Auto/ Manual selectable, default is Auto.
zGamma: CURVE_1_6，CURVE_1_8,CURVE_2_0,CURVE_2_2 totally four modes, default is CURVE_2_0
zAnti-Fliker: Auto, 50hz, 60hz, the default is Auto
After all parameters setting completed, click “Save” and the it comes into effect immediately.
Motion Detection
IP Camera “Motion Detection” setting interface as figure 3-16.

Honeywell
14
Figure 3-16
zEnable: Select whether open the motion detection function.
zAlarm Schedule: Set the alarm schedule from Monday to Sunday.
zDrawing: Click Drawing, then set the detective area.
zClear: Click Clear to clear the current detective areas.
zSensitivity: The higher of the sensitivity, the obvious of the motion detective.
zEmail: Send Email to appointed mailbox when alarm triggered.
zSnap: Snapshot and install the picture in the HDD when alarm triggered.
zAlarm Output: There is a warner connect the alarm output port, alarm triggered the embedded relay switch to make alarm output.
zEnable PTZ: Alarm input to link the PTZ motion.
zPreset: Alarm input to link the preset.
zSnap Interval: Set the snapshot interval time
zSnap Count: Set the snapshot count in every second
After all parameters setting completed, click “Save” and the it comes into effect immediately.
Video Tampering
IP Camera “Video Tampering” setting interface as figure 3-17.