Honeywell NightHawk HCD82484 User manual

Document 900.0391 – 09/05 – Rev 1.00
User Guide
NightHawk® CCD
Cameras
HCC80354 HCC80354X
HCC80484 HCC80484X
HCD80354 HCD81354 HCD82354 HCD80354X HCD81354X HCD82354X
HCD80484 HCD81484 HCD82484 HCD80484X HCD81484X HCD82484X
NTSC/EIA PAL/CCIR
Italiano
Deutsch PortuguêsNederland English
Español Français

Rev 1.00 ii Document 900.0391
09/05
Revisions
Issue Date Revisions
1.00 09/05 New document, based on 900.0375

Rev 1.00 iii Document 900.0391
09/05
Warnings
Installation and servicing should be performed only by qualified
technicians to conform to all local codes and to maintain your warranty.
Explanation of Graphical Symbols
WEEE (Waste Electrical and Electronic Equipment). Correct
disposal of this product (applicable in the European Union and
other European countries with separate collection systems).
This product should be disposed of, at the end of its useful life,
as per applicable local laws, regulations, and procedures.
This symbol indicates the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
This symbol indicates the presence of important
operating and maintenance (servicing) instruction
in the literature accompanying the product.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
CAUTION
English

Rev 1.00 iv Document 900.0391
09/05
FCC Compliance Statement
Information to the User: This equipment has been tested and found to
comply with the limits for a Class A digital device. Pursuant to Part 15 of
the FCC Rules, these limits are designed to provide reasonable
protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à norme NMB-003
du Canada.
Manufacturer’s Declaration of
Conformance
The manufacturer declares that the equipment supplied with this guide is
compliant with the essential protection requirements of the EMC
directive 89/336/EEC and the Low Voltage Directive LVD 73/23 EEC,
conforming to the requirements of standards EN 55022 for emissions,
EN 50130-4 for immunity, and EN 60065 for Electrical Equipment Safety.

Rev 1.00 Document 900.0391
09/05
English
Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Step 1: Connect Video and Power . . . . . . . . . . . . . . . . . . . . . . . . . .3
Step 2: Attach the Camera Base . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Flush Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Flush and Surface Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 3: Position the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 4: Adjust the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Dip Switch Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Adjustment Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjust the Focus and Focal Length . . . . . . . . . . . . . . . . . . . . . . 7
Adjust the Line Lock (Vertical Phase) for 24 VAC Operation . . . 8
Adjust the Backlight Compensation . . . . . . . . . . . . . . . . . . . . . .8
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HC80 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .9
HC81 and HC82 Technical Specifications . . . . . . . . . . . . . . . . .10
Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Europe and United Kingdom . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Mounting Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Rev 1.00 1 Document 900.0391
09/05
Overview
The HC80, HC81, and HC82 Night Hawk® CCD cameras provide true
24/7 surveillance. These small, discreet cameras take perfectly exposed
pictures no matter what the lighting conditions.
The HC81 and HC82 cameras have built-in, infrared LED illuminators to
improve low light viewing. The HC81 camera has 18 near-infrared light
emitting diodes that provide short-range illumination. The HC82 has 48
near-infrared light emitting diodes for longer-range illumination.1
The bullet style, track mount design incorporates a rugged, high impact
aluminum housing that is weather tight. Locking security screws and
concealed wiring ensure they are tamper and vandal resistant. These
cameras are ideally suited for medium security installations, either
indoors or outdoors.
1.Night performance illumination differs between camera models: 40 feet (12
m) for the HC81 and 75 feet (23 m) for the HC82. These ranges are approxi-
mate; actual results depend on reflectivity of the scene, weather conditions,
and so on.

Rev 1.00 2 Document 900.0391
09/05
English
Before You Begin
Unpack Everything
Check that the items received match those listed on the order form and
packing slip. The HC80/HC81/HC82 packing box should include, in
addition to this User Guide:
• One fully assembled camera with factory installed video/power
cable
• One hardware kit
If any parts are missing or damaged, contact the dealer you purchased
the camera from or call Honeywell Customer Service.
Equipment Required
• A Phillips screwdriver may help you complete the installation.
• Mounting screws are not supplied. Use mounting screws
appropriate to your particular installation.The holes on the mounting
plate are 3/16 inch in diameter. See “Mounting Templates” on
page 13.
Please read this guide carefully
before you install the HC80, HC81, or
HC82 camera. Keep this guide for
future reference.

Rev 1.00 3 Document 900.0391
09/05
Installation
The HC80/HC81/HC82 cameras are designed for installation on a wall,
ceiling, or on top of a pole. They are weather sealed for indoor or
outdoor locations.
Step 1: Connect Video and Power
Follow Figure 1 for the wiring connection.
Figure 1 Wiring Connection
WARNING!
The use of a CSA Certified/UL Listed
Class 2 power supply is required to
ensure compliance with electrical
safety standards.
BNC Jack
Video
Black -
Red + 12 VDC or 24 VAC Input

Rev 1.00 4 Document 900.0391
09/05
English
Step 2: Attach the Camera Base
Flush Mount
Drill a hole equal to the diameter of the camera base into the wall or
ceiling where you are connecting the camera. Run the power and video
connections through the wall to their destinations. Be sure to screw the
camera into something solid on a flat, smooth surface (for example, a
crossbeam).
Flush and Surface Mount
1. Loosen, but do not remove the security (locking) screws on the
lower and upper locking rings (see Figure 2).
2. Loosen the lower and upper locking rings to access the mounting
screw holes. Once the locking ring is loosened you can adjust the
camera position for easier access to the four mounting screw holes.
3. Screw the camera base to the desired position on the wall, ceiling,
or top of pole. Use four screws appropriate to your installation to
mount the camera.
Note Mounting templates are provided for your use. See page 13
for the HC80 and HC81 and page 14 for the HC82.
Make sure the camera is mounted on a flat, smooth surface.
For Surface Mounting only: To ensure a waterproof installation, the
notch in the camera base that the power and video connections exit
through should be facing down. If the power and video connections
exit the top of the base (wall mounted only), water may pool in the
camera base. Apply appropriate sealant around the notches and
any other gaps between the camera base and the mounting surface.
Step 3: Position the Camera
Caution Do not swivel and position the camera without the
bezel firmly in place. Avoid handling the camera
board or lens to position the field of view as this
may damage the camera.
1. Loosen the security screws on the lower and upper locking rings.
2. Loosen the locking rings and move the camera into position. Swivel
the camera to capture the desired field of view. Tighten the locking
rings to set the position.

Rev 1.00 5 Document 900.0391
09/05
3. Lock the camera into position using the Allen key supplied to tighten
the locking screws on the locking rings.
Step 4: Adjust the Camera
Note If necessary, adjust the camera after it is mounted firmly in
position. Any new changes to the camera position may
require further adjustment of the zoom and focus.
1. Loosen, but do not remove, the three security (locking) screws on
the bezel with the Allen key supplied (see Figure 2).
One security screw is located under the sunhood. This screw is
accessible through the sunhood by removing the small, black,
rubber plug.
2. Carefully pull the bezel towards you until it is clear of the camera.
Note The bezel and camera fit closely together and separating
them may require using a little force. Be sure to pull the
camera straight out of the bezel. After the camera starts to
slide out, the airtight seal will break and the camera then
slides out easily.
3. Set the bezel and camera down in a place where the tempered glass
window cannot be scratched.
Figure 2 Camera Side View
Security screws (x3)
HC82 only Ring locking screws
Upper locking ring
Camera base
Bezel
Lower locking ring
Balls and
sockets for
easy swiveling
and locing