manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Honeywell
  6. •
  7. Security Sensor
  8. •
  9. Honeywell FIRE-LITE ALARMS W-SD355 User manual

Honeywell FIRE-LITE ALARMS W-SD355 User manual

FL-400-004 1 I56-4081-000R
This sensor must be installed in compliance with the control panel system
installation manual and the SLC Wireless Gateway Manual. The installation
must meet the requirements of the Authority Having Jurisdiction (AHJ). Sen-
sors offer maximum performance when installed in compliance with the Na-
tional Fire Protection Association (NFPA); see NFPA 72.
GENERAL DESCRIPTION
Model W-SD355 and W-SD355T are plug-in type smoke sensors that combine
a photoelectronic sensing chamber with wireless communication. The sensors
transmit a digital representation of smoke density through a wireless mesh
to a gateway. The gateway will send the information to the panel when re-
quested. Rotary decade switches are provided for setting the sensor’s address.
(Figure 1)
Two LEDs on the sensor are controlled by the panel to indicate sensor status.
Model W-SD355T combines a photoelectronic sensing chamber and 135°F
(57.2°C) fixed temperature heat detector.
Fire-Lite panels offer different features sets across different models. As a re-
sult, certain features of the W-SD355 and W-SD355T may be available on
some control panels, but not on others. The possible features available in the
W-SD355 and W-SD355T, if supported by the control unit are:
• The panel controls the LED operation on the sensor. Operational modes
include red, green and amber colors in various solid or blink patterns.
Please refer to the operation manual for the UL listed control unit for specific
operation of the W-SD355 and W-SD355T.
The W-SD355 and W-SD355T require compatible addressable communica-
tions to function properly. Connect these sensors to listed-compatible control
panels only.
SPACING
Fire-Lite recommends spacing sensors in compliance with NFPA 72. In low
air flow applications with smooth ceilings, space sensors 30 feet apart. For
specific information regarding sensor spacing, placement, and special appli-
cations, refer to NFPA 72 or the System Smoke Detector Application Guide,
available from Fire-Lite.
NOTE: Do not attach the base and detectors to temporary structures such as
removable ceiling tiles such that the placement could be altered. To prevent
changes in device placement, permanently secure the structure or mount the
detector across the ceiling panel support as shown in Figure 2.
BATTERY REPLACEMENT
Low battery levels on the wireless devices are displayed as a trouble on the
FACP. Therefore when the message “TROUBLE BATTERY LOW” is displayed,
replace the battery in the device. This message is an indication that approxi-
mately one week of battery life remains.
W-SD355 and W-SD355T Wireless
Intelligent Photoelectric Smoke Sensor
I56-4081-000R
INSTALLATION AND MAINTENANCE INSTRUCTIONS
SPECIFICATIONS
Operating Voltage Range: 3.3 VDC
Standby Current: 210µA @ 3.3 VDC (one communication every 23.8 seconds with LED blink enabled)
Maximum Alarm Current (LED on): 5 mA @ 3.3 VDC LED on
Maximum Transmit RF Power: 17dBm
Radio Frequency Range: 902-928 MHz
Operating Humidity Range: 10% to 93% Relative Humidity, Non-condensing
Operating Temperature Range: 32°F to 120°F (0°C to 49°C),W-SD355; 32°F to 100°F (0°C to 38°C),W-SD355T
Battery Type: 4 Panasonic CR123A or 4 Duracell DL123A
Battery Life: 1 year minimum
Battery Replacement: Upon TROUBLE BATTERY LOW display and/or during annual maintenance
Height: 2.4in. (61 mm) installed in B501W Base
Diameter: 4.0in. (102 mm) installed in B501W Base
Weight: 8.1 oz. (230 g) installed in B501W base with 4 batteries
To replace the batteries in a wireless device use the following steps:
1. Have 4 CR123A (or DL123A) batteries available
2. The system allows 200 seconds to replace the batteries before the device is
noted as missing and will activate the Rescue Mode within the wireless system.
3. Remove the detector from the base.
4. Open the battery compartment refer to Figure 3. Note: The battery compart-
ment cover may be left attached at the hinges during battery replacement.
5. Remove the used batteries and replace with new batteries. The battery
compartment is designed such that the batteries can only align in the ap-
propriate direction. Do not force the batteries into the openings.
6. Replace the battery compartment cover.
7. Return the device to its original location.
CAUTION
Dust covers provide limited protection against airborne dust particles during ship-
ping. Dust covers must be removed before the sensors can sense smoke. Remove
sensors prior to heavy remodeling or construction.
TENS ONES
9
10
11
12
13
14
15
8
7
6
5
4
3
210
9
8
7
6
5
4
3
210
C0162-00
FIGURE 1. ROTARY ADDRESS SWITCHES:
One FireLite Place
Northford, CT 06472
Phone: 203.484.7161
MANUFACTURER MODEL
Home Safeguard Industries 25S and 30S
SDi CHEK02 and CHEK06
SDi SOLOA4
SDi SMOKESABRE-01
When used properly, the canned smoke agent will cause the smoke detector
to go into alarm. Refer to the manufacturer’s published instructions for proper
use of the canned smoke agent.
CAUTION
Canned aerosol simulated smoke (canned smoke agent) formulas will vary by
manufacturer. Misuse or overuse of these products may have long term ad-
verse effects on the smoke detector. Consult the canned smoke agent manufac-
turer’s published instructions for any further warnings or caution statements.
C. Direct Heat Method (Hair dryer of 1000-1500 watts).
A hair dryer of 1000-1500 watts should be used to test the thermistors. Di-
rect the heat toward either of the two thermistors, holding the heat source
approximately 12 inches from the detector in order to avoid damaging
the plastic housing. The detector will reset only after it has had sufficient
time to cool. Make sure both thermistors are tested individually.
A sensor that fails any of these tests should be cleaned as described under
CLEANING, and retested. If the sensor fails after cleaning, it must be replaced
and returned for repair.
When testing is complete, restore the system to normal operation and notify
the proper authorities that the system is back in operation.
CLEANING
Before removing the detector, notify the proper authorities that the smoke de-
tector system is undergoing maintenance and will be temporarily out of service.
Disable the zone or system undergoing maintenance to prevent unwanted alarms.
1. Remove the sensor to be cleaned from the system.
2. Remove the sensor cover by pressing firmly on each of the four removal
tabs that hold the cover in place. (refer to Figure 5).
3. Vacuum the screen carefully without removing it. If further cleaning is
required continue with Step 4, otherwise skip to Step 7.
4. Remove the chamber cover/screen assembly by pulling it straight out.
5. Use a vacuum cleaner or compressed air to remove dust and debris from
the sensing chamber.
6. Reinstall the chamber cover/screen assembly by sliding the edge over the
sensing chamber. Turn until it is firmly in place.
7. Replace the cover using the LEDs to align the cover and then gently
pushing it until it locks into place. Make sure that the thermistors do not
become bent under the cover on the W-SD355T.
8. Reinstall the detector.
9. Test the detector as described in TESTING.
10. Reconnect disabled circuits.
11. Notify the proper authorities that the system is back on line.
SPECIAL NOTE REGARDING SMOKE DETECTOR GUARDS
Smoke detectors are not to be used with detector guards unless the combina-
tion has been evaluated and found suitable for that purpose.
FL-400-004 2 I56-4081-000R
BATTERY
COMPARTMENT
COVER
FIGURE 2. CEILING PANEL SUPPORT:
FIGURE 3. BATTERY COMPARTMENT:
TAMPER RESISTANCE
W-SD355 and W-SD355T include a tamper-resistant capability that prevents
their removal from the base without the use of a tool. Refer to the base man-
ual for details on making use of this capability. The base also includes a mag-
net for tamper resistance. The magnet activates a supervisory tamper fault at
the panel if the detector is removed from the base.
TESTING
Before testing, notify the proper authorities that the system is undergoing
maintenance, and will temporarily be out of service. Disable the system to
prevent unwanted alarms.
All sensors must be tested after installation and periodically thereafter. Testing
methods must satisfy the Authority Having Jurisdiction (AHJ). Sensors offer max-
imum performance when tested and maintained in compliance with NFPA 72.
The sensor can be tested in the following ways:
A. Functional: Magnet Test (P/N M02-04-01 or M02-09-00)
This sensor can be functionally tested with a test magnet. The test mag-
net electronically simulates smoke in the sensing chamber, as well as
tests the sensor electronics and connections to the control panel.
1. Hold the test magnet in the magnet test area as shown in Figure 4.
2. The sensor should alarm the panel.
Two LEDs on the sensor are controlled by the panel to indicate sensor
status. Coded signals, transmitted from the panel, can cause the LEDs
to blink, latch on, or latch off. Refer to the control panel technical docu-
mentation for sensor LED status operation and expected delay to alarm.
B. Smoke Entry
The GEMINI model 501 aerosol generator can be used for smoke entry
testing. Set the generator to represent 4%/ft to 5%/ft obscuration as de-
scribed in the GEMINI 501 manual. Using the bowl shaped applicator,
apply aerosol until the panel alarms.
Additionally, canned aerosol simulated smoke (canned smoke agent)
may be used for smoke entry testing of the smoke detector. Tested and
approved aerosol smoke products are:
C2015-00
C1092-00
C2013-00
LED TEST MAGNET
POSITION
MAGNET TEST
MARKER
LED
COVER
REMOVAL
TABS
SENSOR
COVER
W-SD355 W-SD355T
SENSING CHAMBER
COVER AND SCREEN
SENSING
CHAMBER
COVER
REMOVA
L
TABS
FIGURE 5. DETECTOR COMPONENTS:
FIGURE 4. MAGNET TEST MARKERS:
C0145-02
FL-400-004 3 I56-4081-000R
FL-400-004 4 I56-4081-000R
©2014 Fire-Lite
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Please refer to insert for the Limitations of Fire Alarm Systems

This manual suits for next models

1

Other Honeywell Security Sensor manuals

Honeywell Fire Sentry FS7-2173-2RP User manual

Honeywell

Honeywell Fire Sentry FS7-2173-2RP User manual

Honeywell C7961E Operation manual

Honeywell

Honeywell C7961E Operation manual

Honeywell IS-215T User manual

Honeywell

Honeywell IS-215T User manual

Honeywell FS20X Series User manual

Honeywell

Honeywell FS20X Series User manual

Honeywell Notifier FST-951 User manual

Honeywell

Honeywell Notifier FST-951 User manual

Honeywell Lyric W1 User manual

Honeywell

Honeywell Lyric W1 User manual

Honeywell FS24X User manual

Honeywell

Honeywell FS24X User manual

Honeywell RAEGuard 2 PID User manual

Honeywell

Honeywell RAEGuard 2 PID User manual

Honeywell C7915A Owner's manual

Honeywell

Honeywell C7915A Owner's manual

Honeywell SC100 User manual

Honeywell

Honeywell SC100 User manual

Honeywell 2MLF-RD4A User manual

Honeywell

Honeywell 2MLF-RD4A User manual

Honeywell Miller RACDTA-5K6/6FT Operator's manual

Honeywell

Honeywell Miller RACDTA-5K6/6FT Operator's manual

Honeywell PEHA D MLS2500CDRR4 Installation and operation manual

Honeywell

Honeywell PEHA D MLS2500CDRR4 Installation and operation manual

Honeywell Searchline Excel Cross-Duct Release Note

Honeywell

Honeywell Searchline Excel Cross-Duct Release Note

Honeywell 5800PIR User manual

Honeywell

Honeywell 5800PIR User manual

Honeywell Miller TurboLite Series Operator's manual

Honeywell

Honeywell Miller TurboLite Series Operator's manual

Honeywell ESSER 784763 User manual

Honeywell

Honeywell ESSER 784763 User manual

Honeywell Ex-Or Digital Gold Series Installation and operation manual

Honeywell

Honeywell Ex-Or Digital Gold Series Installation and operation manual

Honeywell DUAL TEC DT8050A User manual

Honeywell

Honeywell DUAL TEC DT8050A User manual

Honeywell Ex-Or MLS2500D Installation and operation manual

Honeywell

Honeywell Ex-Or MLS2500D Installation and operation manual

Honeywell MaxLED Centralized Series User manual

Honeywell

Honeywell MaxLED Centralized Series User manual

Honeywell FS19X Series User manual

Honeywell

Honeywell FS19X Series User manual

Honeywell Filtrex TC844A1007 User manual

Honeywell

Honeywell Filtrex TC844A1007 User manual

Honeywell FlexGuard FG-1625F User manual

Honeywell

Honeywell FlexGuard FG-1625F User manual

Popular Security Sensor manuals by other brands

Velleman PIR416 user manual

Velleman

Velleman PIR416 user manual

Rielta Ladoga MK-RK installation guide

Rielta

Rielta Ladoga MK-RK installation guide

ITALIANA SENSORI 8058-ISR044 Installation, operation and maintenance manual

ITALIANA SENSORI

ITALIANA SENSORI 8058-ISR044 Installation, operation and maintenance manual

DOL 104 0-10 V Technical user guide

DOL

DOL 104 0-10 V Technical user guide

TimeTec Water Leak Detector user guide

TimeTec

TimeTec Water Leak Detector user guide

Response Alarms CA2000P Installation and operating instructions

Response Alarms

Response Alarms CA2000P Installation and operating instructions

OKM eXp 4500 user manual

OKM

OKM eXp 4500 user manual

DMP Electronics 1183 Series installation guide

DMP Electronics

DMP Electronics 1183 Series installation guide

Risco Beyond Wireless DT installation instructions

Risco

Risco Beyond Wireless DT installation instructions

Texecom CAPTURE D20-W manual

Texecom

Texecom CAPTURE D20-W manual

Electric Fuel WAB-H12 operating instructions

Electric Fuel

Electric Fuel WAB-H12 operating instructions

Singing rock TARZAN ECONOMIC manual

Singing rock

Singing rock TARZAN ECONOMIC manual

Trilite SG10-12RG installation instructions

Trilite

Trilite SG10-12RG installation instructions

teko Astra-7 user guide

teko

teko Astra-7 user guide

Alula RE109 install guide

Alula

Alula RE109 install guide

Seitron BEAGLE manual

Seitron

Seitron BEAGLE manual

Aerox 4110-725 SERIES OPERATING INSTRUCTIONS AND EQUIPMENT LIMITATIONS

Aerox

Aerox 4110-725 SERIES OPERATING INSTRUCTIONS AND EQUIPMENT LIMITATIONS

STEINEL IS NM 360 installation instructions

STEINEL

STEINEL IS NM 360 installation instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.